S9ZTEW434APB54Mbps Wireless Access Point with PoE

i Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. ii CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Protection requirements for health and safety – Article 3.1a Testing for electric safety according to EN 60950 has been conducted. These are considered relevant and sufficient. Protection requirements for electromagnetic compatibility – Article 3.1b Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489- 17 and EN 55024 has been conducted. These are considered relevant and sufficient. Effective use of the radio spectrum – Article 3.2 Testing for radio test suites according to EN 300 328-2 has been conducted. These are considered relevant and sufficient. CE in which Countries where the product may be used freely: Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland. France: The use of other channels that the channel 10 through 13 is prohibited by law. iii TABLE OF CONTENT About This Guide ..........................................................................................................1 Purpose......................................................................................................................1 Overview of this User’s Guide ....................................................................................1 Unpacking and Setup....................................................................................................2 Unpacking ..................................................................................................................2 Setup..........................................................................................................................2 Hardware Instalation .....................................................................................................3 Front panel .................................................................................................................3 Rear Panel .................................................................................................................3 Hardware connections................................................................................................4 Connect to the Switch/Hub ......................................................................................4 Check the installation...............................................................................................4 Configuring the Wireless LAN Access Point..................................................................5 Login to the Wireless AP through WLAN ....................................................................5 Login ..........................................................................................................................5 Main Screen of the Access Point................................................................................6 Wizard ........................................................................................................................7 Status.........................................................................................................................9 Basic Setting ............................................................................................................11 Access Point Mode ................................................................................................11 AP Client mode......................................................................................................15 WDS mode ............................................................................................................18 AP+WDS mode ...........................................................................…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

FCC ID .: S9ZTEW434APB Label Location

Page 4 Page 5 Page 6

FCC ID: S9ZTEW434APB Report No. RF951030L04A Operational Description This device is a 54Mbps Wireless Access Point with PoE in the 2.4GHz frequency spectrum with throughput of up to 54Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by AC adapters and POE. The antenna is Dipole antenna with RSMA connector. The other instruction, please have a look at the users manual.

FCC ID: S9ZTEW434APB Report No: SA951030L04A 1 RF EXPOSURE REPORT REPORT NO.: SA951030L04A MODEL NO.: TEW-434APB SERIES MODEL NO.: TEW-433APBO ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: TRENDware International Inc. ADDRESS: 20675 Manhanttan Place, Torrance, CA 90501, USA ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC ID: S9ZTEW434APB Report No: SA951030L04A 2 RF Exposure Measurement (Mobile Device) 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz FCC ID: S9ZTEW434APB Report No: SA951030L04A 3 3. Friis Formula Friis transmission formula: Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref.: David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4 EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification The antenna of the product, under normal use condition, is at least 20cm away from the body of the user. Warning statement for keeping 20cm-separation distance and the prohibition of operating next to a person has been printed on the user’s manual. So, this product is classified as the Mobile Device. FCC ID: S9ZTEW434APB Report No: SA951030L04A 4 6 Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 2dBi or 1.585 (numeric). 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: For 802.11b DSSS MODULATION: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 50.466 0.016 1.0 6 2437 50.119 0.016 1.0 11 2462 50.466 0.016 1.0 For 802.11g OFDM MODULATION: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 64.121 0.020 1.0 6 2437 64.417 0.020 1.0 11 2462 63.387 0.020 1.0

Report No.: RF951030L04A 1 Report Format Version 2.0.5 Reference No.: 960416L11 FCC TEST REPORT REPORT NO.: RF951030L04A MODEL NO.: TEW-434APB SERIES MODEL NO.: TEW-433APBO RECEIVED: Nov. 14, 2006 TESTED: Nov. 14, 2006 ~ Jan. 08, 2007 ISSUED: May 15, 2007 APPLICANT: TRENDware International Inc. ADDRESS: 20675 Manhanttan Place, Torrance, CA 90501, USA ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: 47 14 th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Kueishan, Taoyuan, Taiwan, R.O.C. This test report consists of 78 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF951030L04A 2 Report Format Version 2.0.5 Reference No.: 960416L11 Table of Contents 1 CERTIFICATION......................................................................................................................... 4 2 SUMMARY OF TEST RESULTS ................................................................................................ 5 2.1 MEASUREMENT UNCERTAINTY ............................................................................................. 5 3 GENERAL INFORMATION......................................................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT........................................................................................... 6 3.2 DESCRIPTION OF TEST MODES............................................................................................. 8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST........................................................................ 8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL........................................... 10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.......................................................... 12 3.4 DESCRIPTION OF SUPPORT UNITS..................................................................................... 12 4 TEST TYPES AND RESULTS .................................................................................................. 13 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................................... 13 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................ 13 4.1.2 TEST INSTRUMENTS.............................................................................................................. 13 4.1.3 TEST PROCEDURES .............................................................................................................. 14 4.1.4 DEVIATION FROM TEST STANDARD .................................................................................... 14 4.1.5 TEST SETUP............................................................................................................................ 15 4.1.6 EUT OPERATING CONDITIONS ............................................................................................. 15 4.1.7 TEST RESULTS ....................................................................................................................... 16 4.2 RADIATED EMISSION MEASUREMENT ................................................................................ 34 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT ............................................................. 34 4.2.2 TEST INSTRUMENTS.............................................................................................................. 35 4.2.3 TEST PROCEDURES .............................................................................................................. 36 4.2.4 DEVIATION FROM TEST STANDARD .................................................................................... 36 4.2.5 TEST SETUP............................................................................................................................ 37 4.2.6 EUT OPERATING CONDITIONS ............................................................................................. 37 4.2.7 TEST RESULTS ....................................................................................................................... 38 4.3 6dB BANDWIDTH MEASUREMENT ....................................................................................... 47 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT..................................................................... 47 4.3.2 TEST INSTRUMENTS.............................................................................................................. 47 4.3.3 TEST PROCEDURE................................................................................................................. 48 4.3.4 DEVIATION FROM TEST STANDARD .................................................................................... 48 4.3.5 TEST SETUP............................................................................................................................ 48 4.3.6 EUT OPERATING CONDITIONS ............................................................................................. 48 4.3.7 TEST RESULTS ....................................................................................................................... 49 4.4 MAXIMUM PEAK OUTPUT POWER ....................................................................................... 55 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ....................................... 55 4.4.2 TEST INSTRUMENTS.............................................................................................................. 55 4.4.3 TEST PROCEDURES .............................................................................................................. 56 4.4.4 DEVIATION FROM TEST STAND…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Test Mode A 2 Test Mode B 3 Test Mode C 4 RADIATED EMISSION TEST Test Mode A 5 Test Mode B 6 Test Mode C