SBC-RM3510Radio Module

FuzzyScan Wi-Fi Module RM3510 User’s Guide 2 Introduction You can connect to other Wi-Fi wireless devices by integrating the RM3510 module to yo ur device. 3 Specification Brand Name Ci no Product Name Wi-Fi Module Model Number RM3510 RF Standard IEEE 802.11b/g RF Frequency Country dependant; Typical 2.4 to 2.5 GHz Data Modulation DSSS(DBPSK/ DQPSK/ CCK) OFDM(BPSK/QPSK/16QAM/64QAM) Data Rate (Mbps) DSSS(1/2/5.5/11); OFDM(6/9/12/18/24/36/48/54) Channel Number 11b/g: 11 Channel Band Width (99%) 11b: 13.88MHz; 11g: 16.52MHz Conducted Output Power 11b: 8.94 dBm 11g: 10.86 dBm Power Type From host Dimension 12.5 x 16.6 mm Operating Temperature -10 ~ +50 °C Storage Temperature -40 ~ +70 °C Humidity 5 ~ 95% (non-condensing) 4 Pin Assignment No Pin Name Type Description 1 GND GND Ground 2 SD_D1 I/O SDIO 4-bit Mode: Data Line Bit [1] G-SPI Mode: G-SPI Data Output 3 SD_D3 I/O SDIO 4-bit Mode: Data Line Bit [3] 4 RESETn I Reset (Active Low) , leave open if no use. 5 SD_CLK I/O SDIO 4-bit Mode: Clock Input G-SPI Mode: G-SPI Clock Input 6 SD_CMD I/O SDIO 4-bit Mode: Command / Response G-SPI Mode: G-SPI Data Input 7 N/C 8 N/C 9 N/C 10 VDD_33 POWER Connect to 3.3V DC supply 11 N/C 12 SD_D0 I SDIO 4-bit Mode: Data Line Bit [0] G-SPI Mode: G-SPI Chip Select Input (Active Low) 13 SD_D2 I/O SDIO 4-bit Mode: Data Line Bit [2] G-SPI Mode: G-SPI Interrupt Output (Active Low) 14 N/C 15 GND GND Ground 16 WL_ACTIVE O WLAN Active (Active Low) 2-Wire BCA Mode When high, WLAN is transmitting or receiving packets. 3-Wire BCA Mode 0 = Bluetooth device is allowed to transmit 1 = Bluetooth device is not allowed to transmit Internal 50kohm pull-down. This pin drives low when PDn is asserted. In WLAN Sleep mode, all I/O Pads are powered down. This Pad must stay at a low state even in power down mode. Please make it open when do not use it. 17 PDn I Pull up by 100kohm, Full Power Down (Active Low) 18 GPIO_0 I/O General I/O Port , leave open if no use. 19 GND GND Ground 5 Regulatory Information The Wi-Fi is designed to be interoperable with any Wi-Fi technology product that is in corporating Direct Sequence Spread Spectrum (DSSS) and OFDM data modulation and complies with the IEEE 802.11b/g. Safety The Wi-Fi, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this device, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The Wi-Fi device operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of a Wi-Fi device may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations include the following:
Using the Wi-Fi equipment onboard airplanes, or
Using the Wi-Fi equipment in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If uncertain of the policy that applies to the use of wireless devices in a specific organization or environment (an airport, for example), ask for authorization to use the Wi-Fi device before turning it on. This device has been certified to the following radio standards: FCC Part 15 Subpart C, IC Part 15 Subpart C CE EN300 328, Taiwan LP0002 (NCC) Japan TELEC T401 (MIC) 6 Warning 802.11b/802.11g/BT警語 警 語警語 警語： ：： ： 第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得 擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現 象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻射性電機設備之干擾。 7 Federal Communication Commission Interference Statement FCC Caution: Any changes or modifications not expressly approved by the party re sp onsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. L ABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: SBC-RM3510 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Date: February 22, 2012 Subject: Ad Hoc Mode Function Declaration FCC ID: SBC-RM3510 To Whom it may concern, We, PC Worth Int’l Co., Ltd., declare that the device (FCC ID: SBC-RM3510 ) 1. is acting as slave and operating on 2.4GHz band. 2. Ad Hoc function is available. 3. is not able to operate in non-US/IC frequencies, country code selection will be disable for this device. Please contact the one signed below or the authorized agent for this filing. Thank you. Regards, Applicant : PC Worth Int’l Co., Ltd. Address : 18F, No. 100, Sec.1,Xintal 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan,( R.O.C.) Signature : _________________________________ Name and Job Title. : Johnson Yu / VP, Chief Design Architect E-mail [email protected] Te l . 886-2-2696-2559 Extension 8004

Module Approval Request Letter Subject: Module Approval request letter Date: 3/6/2012 FCC ID: SBC-RM3510 Dear Reviewer, We, PC Worth Int’l Co., Ltd., would request Radio Module approved under module approval authorization. The requirements regulated in 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip ( IS25C08). 3. The requirement of power supply regulation: The part number of the power regulator is (RP102). 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE. Please do not hesitate to contact me for any questions of this request letter. Thank you. Applicant’s company name : PC Worth Int’l Co., Ltd. Applicant’s company address : 18F, No. 100, Sec.1,Xintal 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan,( R.O.C.) Signature : _________________________________ Job Title and Dept. : Johnson Yu / VP, Chief Design Architect E-mail : [email protected] Te l . : 886-2-2696-2559 Extension 8004

Confidentiality Request Letter Date: 2012/2/22 Federal Communications Commission Authorization and Evaluation Division FCC ID：SBC-RM3510 Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below: 1. Block Diagram 2. Circuit Diagram 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Applicant’s company name : PC Worth Int’l Co., Ltd. Applicant’s company address : 18F, No. 100, Sec.1,Xintal 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan,( R.O.C.) Signature : _________________________________ Job Title and Dept. : Johnson Yu / VP, Chief Design Architect E-mail : [email protected] Te l . : 886-2-2696-2559 Extension 8004

Date: 2012/2/22 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Product Certification Representative Authorization Letter FCC ID: SBC-RM3510 Product name: Radio Module To whom it may concern: We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization of model RM3510 to the FCC Rules and Regulations. Sporton International Inc. Address : No. 52, Hwa Ya 1st Road., Kwei-Shan Hsiang, TaoYuan Hsien Taiwan R.O.C. Name : Wayne Hsu Job Title : Vice Manager e-mail : [email protected] We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant : PC Worth Int’l Co., Ltd. Address : 18F, No. 100, Sec.1,Xintal 5th Rd., Xizhi Dist., New Taipei City 221, Ta i w a n , ( R . O. C . ) Signature : _________________________________ Name and Job Title. : Johnson Yu / VP, Chief Design Architect E-mail : [email protected] Te l . : 886-2-2696-2559 Extension 8004

FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C1 OF C2 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 12, 2012 FAX : 886-2-2696-2255 APPENDIX C. Photographs of EUT FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C2 OF C2 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 12, 2012 FAX : 886-2-2696-2255

FCC ID:SBC-RM3510 10mm 12mm FCC ID:SBC-RM3510 10mm 12mm FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C1 OF C2 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 12, 2012 FAX : 886-2-2696-2255 APPENDIX C. Photographs of EUT

FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C1 OF C2 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 12, 2012 FAX : 886-2-2696-2255 APPENDIX C. Photographs of EUT FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C2 OF C2 TEL : 886-2-2696-2468 ISSUED DATE : Jan. 12, 2012 FAX : 886-2-2696-2255

Page No. : A1 of A3 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 Appendix A. RF Exposure Evaluation Page No. : A2 of A3 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) = d GP30 Power Density: Pd (W/m²) = 377 2 E E = Electric field (V/m) P = Peak RF output power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = 2 377 30 d GP   From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Page No. : A3 of A3 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 1.3. Calculated Result and Limit Antenna Type : Chip Antenna Operating Frequency (GHz) Min. User Distance (cm) Gain (dBi) Numeric Gain Output Power (dBm) Conducted Power (mW) Power Density (mW/cm2) 2.462 20 4 2.511886 10.86 12.1899 0.0061

SPORTON International Inc. Report Format Version: a FCC TEST REPORT Report No. : FR180535 FCC RADIO TEST REPORT according to 47 CFR FCC Part 15 Subpart C § 15.247 Equipment: Radio Module Brand Name : Cino Model No. : RM3510 Filing Type: New Application Applicant Manufacturer : PC Worth Int’l Co., Ltd. 18F, No. 100, Sec. 1, Xintai 5 th Rd., Xizhi Dist, New Taipei City 221, Taiwan (R.O.C.) FCC ID : SBC-RM3510 Received Date : Nov. 24, 2011 Final Test Date : Jan. 11, 2012 Statement Test result included is only for the 802.11b/g part of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. SPORTON International Inc. No. 52 Hwa Ya 1 st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. SPORTON International Inc. Page No. : i of ii TEL : 886-2-2696-2468 Issued Date: Jan. 12, 2012 FAX : 886-2-2696-2255 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 Table of Contents 1 SUMMARY OF THE TEST RESULT ....................................................................................................................... 2 2 GENERAL INFORMATION ...................................................................................................................................... 3 2.1 Product Details .........................................................................................................................................................................................3 2.2 Table for Filed Antenna ............................................................................................................................................................................3 2.3 Table for Carrier Frequencies ..................................................................................................................................................................3 2.4 Table for Test Modes ...............................................................................................................................................................................3 2.5 Table for Testing Locations ......................................................................................................................................................................4 2.6 Table for Supporting Units .......................................................................................................................................................................4 2.7 Table for Parameters of Test Software Setting ........................................................................................................................................4 2.8 EUT Operation during Test ......................................................................................................................................................................4 2.9 Test Configuration ....................................................................................................................................................................................5 3 TEST RESULT ......................................................................................................................................................... 6 3.1 AC Power Line Conducted Emissions Measurement ..............................................................................................................................6 3.2 Peak Output Power Measurement .........................................................................................................................................................10 3.3 Power Spectral Density Measurement ...................................................................................................................................................12 3.4 6dB Spectrum Bandwidth Measurement ...............................................................................................................................................18 3.5 Radiated Emissions Measurement ........................................................................................................................................................28 3.6 Band Edge and Fundamental Emissions Measurement ........................................................................................................................46 3.7 Antenna Requirements ..........................................................................................................................................................................51 4 LIST OF MEASURING EQUIPMENTS .................................................................................................................. 52 5 TEST LOCATION ................................................................................................................................................... 54 6 TAF CERTIFICATE OF ACCREDITATION ........................................................................................................... 55 APPENDIX A. MAXIMUM PERMISSIBLE EXPOSURE ................................................................................. A1 ~ A3 APPENDIX B. TEST PHOTOS ........................................................................................................................ B1 ~ B7 APPENDIX C. PHOTOGRAPHS OF EUT ....................................................................................................... C1 ~ C2 SPORTON International Inc. Page No. : ii of ii TEL : 886-2-2696-2468 Issued Date: Jan. 12, 2012 FAX : 886-2-2696-2255 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180…

Text truncated - open the document above for the full version.

Page No. : B1 of B7 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 Appendix B. Test Photos Page No. : B2 of B7 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 1 Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Page No. : B3 of B7 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 SIDE VIEW Page No. : B4 of B7 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 2 Photographs of Radiated Emissions Test Configuration For radiated emissions 9kHz~30MHz FRONT VIEW REAR VIEW Page No. : B5 of B7 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 For radiated emissions 30MHz~1GHz FRONT VIEW REAR VIEW Page No. : B6 of B7 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 For radiated emissions above 1GHz FRONT VIEW REAR VIEW Page No. : B7 of B7 FCC ID : SBC-RM3510 FCC TEST REPORT Report No. : FR180535 EUT take a close-up EUT