SEJ-8101081010

REV: 08/24/12 As Zonar Systems is continuously improving the Product, Zonar may make changes to the Product at any time which may not be reflected in this document. INTRODUCTION 2 Zonar Systems Virtual Trainer™ Hardware Installation Tips for Professional Installers Zonar Systems’ equipment will provide years of reliable service if properly installed and maintained. Zonar equipment is typically installed in heavy vehicle applications and is often subject to extreme temperatures, dust, dirt, vibration, and shock. Proper installation is the critical first step to equipment longevity and optimal performance. This guide is meant to be a general guideline for the professional installer and technician. While we attempt to point out the most common installation questions and issues; common sense, good housekeeping procedures, attention to detail, safety adherence, and technical competence of the professional installer is critical for a successful installation. Please refer to your specific vehicle manufacturer guidelines for the installation of electrical components and wiring. A professional team of Zonar support technicians and engineers are available to answer your installation questions. Contact Zonar at 1-877-843-3847 or by email at [email protected]. Thank you, Jeff Wells Field Service Manager - Zonar Systems TABLE OF CONTENTS 3 © 2012 Zonar Systems • EVIR, ZPass,Ground Traffic Control and V3 are trademarks of Zonar Systems. All Rights Reserved. Products and services protected by one or more of the following US patents: 6,671,646; 6,804,626; 7,557,696; 7,117,121; 7,362,229; 7,564,375; 7,680,595; 7,776,499; 7,808,369; 7,944,345; 8,106,757, plus EP 2756504.3 and the AU. REV: 08/24/12 Virtual Trainer ™ Introduction.......................................................................................2 System Overview...............................................................................4 Equipment.........................................................................................5 System Specifications........................................................................6 General Guidelines.............................................................................7 Installation ........................................................................................8 System Checklist...............................................................................9 Warranty & Notices - FCC Compliance............................................10 Notes...............................................................................................11 SYSTEM OVERVIEW 4 • RFID to log drivers into vehicle • Displays warnings and alerts to improve driver performance • Track driver performance over time CUSTOMER On-Site Location ZONAR Secure Servers Encrypted Data Transmissions CELL TOWER INTERNET VIRTUAL TRAINER™ EQUIPMENT 5 A.VIRTUAL TRAINER B.VIRTUAL TRAINER Mounting Plate and Mounting Screws (Provided) C.Mounting Plate adhesive pad VIRTUAL TRAINER SPECIFICATIONS/DIMENSIONS 6 1.827 3.627 .927 DIMENSIONS IN INCHES System Specifications VIRTUAL TRAINER™ •Operating Temp -40C to +85C •Operating Humidity to 95% •DC Input range, 5Vdc - Supplied from Host Connector •6 pin Molex RFID Reader •Reads Driver Card from a range of at least 1/2 inch Host Devices •V2™, V2J™, VTECU™, V3™ Important Notice It is the Owner's sole responsibility to install and use the Zonar products in a manner that will not cause accidents, personal injury or property damage. For the purposes of this notice, "Owner", "you" and "your" means the party (including any person authorized by that party to use and/or install the Product) that has either: (a) purchased the Product; or (b) leased the Product from Zonar Systems, Inc or its related companies. The Owner of this product is solely responsible for observing safe driving practices. The choice, location, and installation of all components of the Product is critical. If installation is not correct, the Product may not perform at its designed potential or specifications. If in doubt, consult your vehicle's manufacturer. 7 GENERAL GUIDELINES Layout 1) V3 unit must be located a minimum of 8” from any person. 2)V3 has a temperature range of -40 ̊C (-40 ̊F) to +85 ̊C (+185 ̊F). Do not mount V3 in hot engine compartments or near hot exhaust components. 3)Lay all components out prior to installation to check for proper cable length and interference issues. 4)Avoid mounting Zonar equipment, antennas and wiring near other radio equipment (e.g.,two-way radios), PA equipment and high energy electrical sources (e.g., cables, relays, amplifiers, etc.). Electrical 1)Consult the vehicle’s manufacturer for specific installation guidelines. (HIGHLY RECOMMENDED for Multiplex electrical systems) 2)All power leads (Red and White Power leads) must be connected to the vehicles protected circuitry (e.g. fuse panel, circuit breaker panel, protected circuits). Never electrically connect Zonar equipment to unprotected circuits (e.g. directly to battery). 3)It is also required that all power leads (Red and White Power leads) be protected with a 3 to 5 amp fuse and inline fuse holder (included) for optimal system protection. 4)Electrical fuses should be installed as close as possible to the source of power. Drill Holes 1)Do not drill into the V3 unit. This will void the warranty. 2)Capture all drill chips during drilling operations. Do not allow chips to fall onto equipment, furnishings, etc. 3)Deburr all drill holes on both sides of drilled surface. Example deburr tool: 4)All drill holes must have a rubber grommet or similar anti- chaffing system installed to protect cable assemblies (e.g. plastic conduit). 5)Seal all penetration drill holes which may pass rain water. Cable Management 1)Strain relieve and support all cable installations. 2)Avoid sharp bends and tight radius installations of cables. 3)Avoid moving components (e.g. doors, steering shafts, handles, fans, etc.). 4)Provide an …

Text truncated - open the document above for the full version.

WTD 12.7.3 FCC Compliance Opinion ZONA0041 Information about the Applicant Grantee (Company Name) Zonar Systems, LLC FCC Contact Person Kelly Niemi Address 18200 Cascade Ave. S Suite, 200 City, State, Zip Seattle, WA 98188 Job Number ZONA0041 Model Virtual Trainer FCC ID SEJ-81010 Agent Approval Type Original Equipment Class DCD Part 15, low power Tx below 1.705 MHz Rule Part 15.209 Overview Zonar Systems is seeking original approval for their Virtual Trainer device under FCC rule part 15.209, FCC ID SEJ-81010. The Virtual Trainer is a short range RFID Reader operating at 125 kHz. Confidentiality requested for allowed files. Request is properly addressed and referenced. No short term confidentiality requested. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Dave Tolman, TCB Committee 9/18/2012

Virtual Trainer External Photos This document is provided to show external photos of the Virtual Trainer in accordance with FCC requirements per 2.1033(b)(7). Figure 1 Front Figure 2 Side 1 Figure 3 Side 2 Figure 4 Side 3 Figure 5 Side 4 Figure 6 Back

FCC ID Label & Location The FCC ID label for the Virtual Trainer is located on the back of the device enclosure. Figure 1 Label located on the enclosure back Figure 2 Label Contents

Virtual Trainer Internal Photos This document is provided to show internal photos of the Virtual Trainer in accordance with FCC requirements per 2.1033(b)(7). Figure 1 Virtual Trainer with antenna Figure 2 Virtual Trainer with antenna un-mounted Figure 3 Virtual Trainer PCB top. Radio section bounded in RED Figure 4 Virtual Trainer PCB Bottom

Virtual Trainer Antenna Information This document provides antenna compliance information for the VIRTUAL TRAINER. a) As per FCC requirement 15.203; the VIRTUAL TRAINER antenna is a coil antenna with a soldered unique coupling to the radio PCB. The coil antenna is secured and housed internal to the VIRTUAL TRAINER enclosure, making it inaccessible for modification or replacement without comprising the device. b) VIRTUAL TRAINER uses a single ~1.04mH coil antenna c) The antenna is Zonar Systems part number 81016 unity gain. d) Details and photos of Virtual Trainer antenna: Figure 1 Coil Antenna leads soldered top right of PCB Figure 2 Coil Antenna secured in enclosure.

Zonar Systems, LLC 81010 Report #: ZONA0039 Report Prepared By Northwest EMC Inc. NORTHWEST EMC – (888) 364-2378 – www.nwemc.com California – Minnesota – Oregon – New York – Washington 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: April 30, 2012 Zonar Systems, LLC Model: 81010 Emissions Test Description Specification Test Method Pass/Fail Field Strength of Fundamental FCC 15.209:2012 ANSI C63.10:2009 Pass Spurious Radiated Emissions FCC 15.209:2012 ANSI C63.10:2009 Pass Deviations From Test Standards None Approved By: Tim O'Shea, Operations Manager NVLAP Lab Code: 200630-0 Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-1). This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Revision History Revision 09/01/11 Revision Number Description Date Page Number 00 None Accreditations and Authorizations Revision 02/21/2012 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC Guide 65 as a product certifier. This allows Northwest EMC to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025. The scope includes radio, ITE, and medical standards from around the world. See: http://www.nwemc.com/accreditations/ Canada IC - Recognized by Industry Canada as a Certification Body (CB). Certification chambers and Open Area Test Sites are filed with IC. European Union European Commission – Validated by the European Commission as a Conformity Assessment Body (CAB) under the EMC directive and as a Notified Body under the R&TTE Directive. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea KCC / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Hong Kong OFTA – Recognized by OFTA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. Russia GOST – Accredited by Certinform VNIINMASH, CERTINFO, SAMTES, and Federal CHEC to perform EMC and Hygienic testing for Information Technology products to GOST standards. Locations Revision 2/23/12 Oregon Labs EV01-EV12 22975 NW Evergreen Pkwy, #400 Hillsboro, OR 97124 (503) 844-4066 California Labs OC01-OC13 41 Tesla Irvine, CA 92618 (949) 861-8918 New York Labs WA01-WA04 4939 Jordan Rd. Elbridge, NY 13060 (315) 685-0796 Minnesota Labs MN01-MN08 9349 W Broadway Ave. Brooklyn Park, MN 55445 (763) 425-2281 Washington Labs SU01-SU07 14128 339 th Ave. SE Sultan, WA 98294 (360) 793-8675 VCCI C-1071, R-1025, G-84, C-2687, T-1658, R-2318 R-1943, G-85, C-2766, T-1659, G-548 R-3125, G-86, G-141, C-3464, T-1634 R-871, G-83, C-3265, T-1511 Industry Canada 2834D-1, 2834D-2 2834B-1, 2834B-2, 2834B-3 2834E-1 2834C-1 Product Description Revision 09/01/11 Client and Equipment Under Test (EUT) Information Company Name: Zonar Systems, LLC Address: 18200 Cascade Ave. S Suite, 200 City, State, Zip: Seattle, WA 98188 Test Requested By: Andrew Mannery Model: 81010 First Date of Test: April 30, 2012 Last Date of Test: April 30, 2012 Receipt Date of Samples: April 30, 2012 Equipment Design Stage: Production Equipment Condition: No Damage Information Provided by the Party Requesting the Test Functional Description of the EUT (Equipment Under Test): 126 kHz RFID unit Testing Objective: To demonstrate compliance to FCC 15.209 requirements. Configurations Revision 09/01/11 Configuration 1 ZONA0039 EUT Description Manufacturer Model/Part Number Serial Number RFID unit Zonar Systems, LLC 81010 unknown Remote Equipment Outside of Test Setup Boundary Description Manufacturer Model/Part Number Serial Number Basestation Zonar Systems, LLC V2J 1017 Cables Cable Type Shield Length (m) Ferrite Connection 1 Connection 2 I/O No 1.8m No Basestation EUT PA = Cable is permanently attached to the device. Shielding and/or presence of ferrite may be unknown. Modifications Revision 09/01/11 Equipment Modifications Item Date Test Modification Note Disposition of EUT 1 4/30/2012 Field Strength of Fundamental Tested as delivered to Test Station. No EMI suppression devices were added or modified during this test. EUT remained at Northwest EMC following the test. 2 4/30/2012 Spurious Radiated Emissions Tested as delivered to Test Station. No EMI suppression devices were added or modified during this test. Scheduled testing was completed. description MODES OF OPERATION Transmitting continuous POWER SETTINGS INVESTIGATED DC from host CONFIGURATIONS INVESTIGATED ZONA0039 - 1 FREQUENCY RANGE INVESTIGATED Start Frequency 110 kHzStop Frequency140 kHz SAMPLE CALCULATIONS Radiated Emissions: Field Strength = Measured Level + Antenna Factor + Cable Factor - Amplifier …

Text truncated - open the document above for the full version.

photo FF 001.jpg FF 002.jpg FIELD STRENGTH OF FUNDAMENTAL PSA-ESCI 2012.03.23 photo FF 003.jpg FF 004.jpg FIELD STRENGTH OF FUNDAMENTAL PSA-ESCI 2012.03.23 photo FF 005.jpg FIELD STRENGTH OF FUNDAMENTAL PSA-ESCI 2012.03.23 photo FF 001.jpg FF 002.jpg SPURIOUS RADIATED EMISSIONS PSA-ESCI 2012.03.23 photo FF 003.jpg FF 004.jpg SPURIOUS RADIATED EMISSIONS PSA-ESCI 2012.03.23 photo FF 005.jpg SPURIOUS RADIATED EMISSIONS PSA-ESCI 2012.03.23