SEJ-V3V3

REV: 07/31/12 As Zonar Systems is continuously improving the Product, Zonar may make changes to the Product at any time which may not be reflected in this document. INTRODUCTION 2 Zonar Systems V3 ™ Hardware Installation Tips For Professional Installers Zonar Systems’ equipment will provide years of reliable service if properly installed and maintained. Zonar equipment is typically installed in heavy vehicle applications and is often subject to extreme temperatures, dust, dirt, vibration, and shock. Proper installation is the critical first step to equipment longevity and optimal performance. This guide is meant to be a general guideline for the professional installer and technician. While we attempt to point out the most common installation questions and issues; common sense, good housekeeping procedures, attention to detail, safety adherence, and technical competence of the professional installer are critical for a successful installation. Please refer to your specific vehicle manufacturer guidelines for the installation of electrical components and wiring. A professional team of Zonar support technicians and engineers are available to answer your installation questions. Contact Zonar at 1-877-843-3847 or by email at [email protected]. Thank you, Andre J Horochiwsky Technical and Training Manager – Zonar Systems EVIR ® • V3 ™ Introduction.......................................................................................2 System Overview...............................................................................4 V3 Equipment....................................................................................5 Optional Equipment - EVIR ® ............................................................... 6 General Guidelines.............................................................................7 V3 Mounting Plate.............................................................................8 V3 Pin Configuration..........................................................................9 Power and Data Connections.....................................................10-11 4 Pin Cable Testing..........................................................................12 GPS 4 Pin Power Cable Management.............................................12 Wiring Guidelines.............................................................................13 Antenna Installation..........................................................................14 GPS VM and Tag Installation............................................................15 GPS System Check.........................................................................16 System Checklist.............................................................................17 System Specifications......................................................................18 Equipment Dimensions...............................................................19-20 Installation Examples..................................................................21-22 System Installation Diagram.............................................................23 Discrete I/O System Installations.................................................24-25 Warranty & Notices - FCC Compliance............................................26 Notes...............................................................................................27 TABLE OF CONTENTS 3 © 2012 Zonar Systems • EVIR, ZPass,Ground Traffic Control and V3 are trademarks of Zonar Systems. All Rights Reserved. Products and services protected by one or more of the following US patents: 6,671,646; 6,804,626; 7,557,696; 7,117,121; 7,362,229; 7,564,375; 7,680,595; 7,776,499; 7,808,369; 7,944,345; 8,106,757, plus EP 2756504.3 and the AU. REV: 07/31/12 Real-Time Delivery of Engine Condition and Performance Data, Driver Performance and Location SYSTEM OVERVIEW 4 CUSTOMER On-Site Location ZONAR Secure Servers Encrypted Data Transmissions CELL TOWER INTERNET Base Equipment A.V3 GPS Unit B.V3 Mounting Plate and Mounting Screws (Provided) C.GPS Antenna (Optional) D.GPS Antenna Aluminum Mount Plate and Screws (Optional - used for non-magnetic rooftop GPS Antenna installs) Note: See page 14 for detailed information on GPS antenna requirements and recommendations. V3™ EQUIPMENT 5 A.2010 RFID EVIR ® Inspection Tool (Optional) B.GPS-VM Vehicle Mount (Optional) and Mounting Screws (Supplied) C.2010 RFID Reader installed in GPS-VM (GPS-Vehicle Mount) - (Optional) D.Zone and Asset Tags (Optional) OPTIONAL EQUIPMENT: EVIR ® 6 Fig. 6-1 - See Pages 19-20 for dimensions GENERAL GUIDELINES 7 Layout 1) V3 unit must be located a minimum of 8” from any person. 2)V3 has a temperature range of -40 ̊C (-40 ̊F) to +85 ̊C (+185 ̊F). Do not mount V3 in hot engine compartments or near hot exhaust components. 3)Lay all components out prior to installation to check for proper cable length and interference issues. 4)Avoid mounting Zonar equipment, antennas and wiring near other radio equipment (e.g.,two-way radios), PA equipment and high energy electrical sources (e.g., cables, relays, amplifiers, etc.). Electrical 1)Consult the vehicle’s manufacturer for specific installation guidelines. (HIGHLY RECOMMENDED for Multiplex electrical systems) 2)All power leads (Red and White Power leads) must be connected to the vehicles protected circuitry (e.g. fuse panel, circuit breaker panel, protected circuits). Never electrically connect Zonar equipment to unprotected circuits (e.g. directly to battery). 3)It is also required that all power leads (Red and White Power leads) be protected with a 3 to 5 amp fuse and inline fuse holder (included) for optimal system protection. 4)Electrical fuses should be installed as close as possible to the source of power. Drill Holes 1)Do not drill into the V3 unit. This will void the warranty. 2)Capture all drill chips during drilling operations. Do not allow chips to fall onto equipment, furnishings, etc. 3)Deburr all dril…

Text truncated - open the document above for the full version.

Redpine Signals, Inc. Proprietary and Confidential RS9110-N-11-02 802.11bgn WLAN Module Data Sheet V V e e r r s s i i o o n n 1 1 . . 4 4 8 8 September 2011 Redpine Signals, Inc. 2107 N. First Street, #680 San Jose, CA 95131. Tel: (408) 748-3385 Fax: (408) 705-2019 Email: [email protected] Website: www.redpinesignals.com Redpine Signals, Inc. Proprietary and confidential Page 2 RS9110-N-11-02 802.11bgn WLAN Module Data Sheet Version 1.48 Overview The RS9110-N-11-02 module is a complete IEEE 802.11bgn Wi-Fi client device with an integrated MAC, Baseband processor, and RF transceiver with power amplifier. Based on the Redpine Signals RS9110-LI MAC/BBP chip, the module provides a complete end-to-end solution for low-power WLAN applications. It includes a multi- threaded processor and a rich set of peripheral interfaces. It can connect to a host processor through SDIO and SPI interfaces. Applications: • VOIP handsets • Interactive remote control devices • Industrial automation and telemetry • MP3 music and MP4 video players • Digital cameras and camcorders Device Features: • Conforms to IEEE 802.11b/g/e/i standards, single-stream 802.11 n • 802.11n MAC features for high user throughput • 802.11n Space Time Block Code (STBC) support for extended range and higher throughput • Host interface through SDIO and SPI • Bluetooth coexistence • Integrated multi-threaded processor • TCP checksum offloading • Rich set of peripherals – UART, SPI, I2C, GPIO, and timers • 2.4 GHz, 802.11n RF transceiver with high performance power amplifier • Complete WLAN software along with host driver for various operating systems such as Windows XP, Linux, Windows CE • Single supply 3.1 to 3.6 V operation RS9110-N-11-02 System Block Diagram RS9110-N-11-02 RF Transce iv er + PA Balun EEPROM T/R Switch Host Interface 3.3V Peripheral I/O Frequency Reference RS9110-LI Redpine Signals, Inc. Proprietary and confidential Page 3 RS9110-N-11-02 802.11bgn WLAN Module Data Sheet Version 1.48 Table of Contents 1: Detailed Feature List ............................................................ 7 1.1: Host Interfaces...................................................................... 7 1.2: WLAN.................................................................................... 7 1.2.1: MAC.............................................................................................. 7 1.2.2: Baseband Processing.................................................................... 7 1.2.3: RF Transceiver.............................................................................. 7 1.3: Multi-Threaded Processor ...................................................... 7 1.4: Peripherals............................................................................ 8 1.5: Coexistence........................................................................... 8 1.6: Software ............................................................................... 8 1.7: Compliance and Certification.................................................. 8 2: Package Description............................................................. 9 2.1: Top View ............................................................................... 9 2.2: Bottom View.......................................................................... 9 2.3: Package Dimensions............................................................ 10 2.4: Recommended Reflow Profile............................................... 11 2.5: Baking Instructions ............................................................. 11 3: Pin Description................................................................... 12 3.1: Module Pinout...................................................................... 12 3.2: Pin Description .................................................................... 12 4: Electrical Characteristics.................................................... 19 4.1: Absolute Maximum Ratings.................................................. 19 4.2: Recommended Operating Conditions.................................... 19 4.3: DC Characteristics – Digital I/O Signals ............................... 19 4.4: AC Characteristics – Digital I/O Signals................................ 20 4.4.1: SDIO Interface ........................................................................... 20 4.4.1.1: Full Speed Mode.................................................................... 20 4.4.1.2: High Speed Mode .................................................................. 21 4.4.2: SPI Interface.............................................................................. 21 4.4.2.1: Full Speed Mode.................................................................... 22 4.4.2.2: High Speed Mode .................................................................. 22 4.4.3: Reset Timing............................................................................... 23 4.4.4: JTAG Interface............................................................................ 24 5: Module Power Consumption............................................... 25 6: Performance Specifications................................................ 26 6.1: Wireless Specifications ........................................................ 26 6.2: Receive Characteristics........................................................ 26 6.2.1: Sensitivity................................................................................... 26 6.3: Standards Compliance ......................................................... 26 7: Software Details................................................................. 28 7.1: Architecture ........................................................................ 28 7.2: Details................................................................................. 28 7.2.1: 802.1x Supplicant....................................................................... 29 7.2.2: Configuration Utility ............…

Text truncated - open the document above for the full version.

Northwest EMC TCB Compliance Opinion Rev. 7/1/10 ZONA0037 Information about the Applicant Grantee (Company Name) Zonar Systems, LLC FCC Contact Person Kelly Niemi Address 18200 Cascade Ave. S Suite, 200 City, State, Zip Seattle, WA 98188 Job Number ZONA0037 Model V3 FCC ID SEJ-V3 Agent Approval Type Original Equipment Class DTS Digital Transmission System PCB - PCS Licensed Transmitter Rule Part 15C (15.247) 22H 24E Overview The V3 device, FCC ID: SEJ-V3, is mounted on heavy vehicles and is use to gather vehicle data and send this data to the Zonar database servers via a 2G/3G GSM modem. The V3 also contains an 802.11 b/g/n radio module. Confidentiality requested for allowed files. Request is properly addressed and referenced. Recommendation All items have been resolved and completed to my satisfaction; therefore I recommend this application for approval. Signature Dave Tolman, TCB Committee 5/31/2012

2107 N. First Street, Suite 680, San Jose CA 95131 – 2019, USA Tel: 408-748-3385 Fax: 408-705-2019 www.redpinesignals.com Date : 12 April2012 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern, We hereby respectfully request that under the provision of 47 CFR 0.459 and 0.457(d), the documents listed below and attached with this application for certification be provided with confidential status. • Schematics • Theory of Operation Any exhibit / information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, A. Chandrasekhar Vice President–Systems Redpine Signals Inc.

April 5, 2012 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for Exhibits in Support of FCC Filing under FCC ID: SEJ-V3 We hereby request that the exhibits listed below for FCC ID: N7NSL8080, submitted in support of the certification application for FCC ID: SEJ-V3, be withheld from public disclosure. This request is made under the provisions of Section 0.457(d) and 0.459 of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act. We cite trade secrets as the reason and purpose of the request.  Schematics  Block Diagram  Operation Description  Tune Up Procedure Best Regards Ying Wang Manager, Regulatory Compliance

ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 V3 External Photos This document is provided to show external photos of the V3 Telematics Device in accordance with FCC requirements per 2.1033(b)(7). Figure 1 Top Figure 2 Side 1 ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 3 Side 2 Figure 4 Side 3 ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 5 Side 4 Figure 6 Bottom ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082

ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 FCC ID Label & Location Document The FCC ID label for the ZpassV2 is located on the back of the device enclosure. This single lable contains the FCC id, the IC id, the Zonar model of ‘V3’ as well as the specific part number, SCID and GPSid number of the particular device. Figure 1 Label located on the enclosure back ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 2 Label Close-up on Backside of Device ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 3 Label Contents Drawing

ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 V3 Internal Photos This document is provided to show internal photos of the V3 Telematics Device in accordance with FCC requirements per 2.1033(b)(7). Figure 1 V3 Component/Bottom Side ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 2 V3 Antenna/Top Side ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 3 V3 GSM Radio Sub-Circuit Figure 4 V3 WiFi radio Sub-Circuit

ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Zonar V3 Telematics Device GSM Antenna Information T his document provides antenna compliance information for the Zonar V3 telematics device. 1) In compliance with FCC requiremens of paragraph 15.203 of the FCC rules; the GSM antenna component is permantly mounded to the printed circuit board. There is no provision made for alternate antennas nor connectivity for any additional/external antenna. 2) The V3 device uses a single surface mount chip type antenna. a. The antenna manufacturer is: Antenova b. Manfacturer part number is: Reflexus c. Specific RF paramaters are as such: Parameter Frequency Value Peak gain 876 MHz 2dBi 1917 MHz 3.7dBi Average gain (Linear) 824-960 MHz -1.3dBi 1710-2170 MHz -1.5dBi Average efficiency 824-960 MHz 70% 1710-217 MHz >60% Maximum Return Loss -8 dB Maximum VSWR 2.3:1 ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 3) Details and photos of V3 antenna: Figure 1 Antenna/Top side of V3 Device GSM antenna in the upper left ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 2 Close-up of GSM sub-circuit with antenna in the lower right ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 3 Top of GSM antenna chip Figure 4 Bottom side of antenna chip showing PCB surface mounting

ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Zonar V3 Telematics Device WiFi Antenna Information T his document provides antenna compliance information for the Zonar V3 telematics device. 1) In compliance with FCC requiremens of paragraph 15.203 of the FCC rules; the WiFi antenna component is permantly mounded to the printed circuit board. There is no provision made for alternate antennas nor connectivity for any additional/external antenna. 2) The V3 device uses a single surface mount chip type antenna. a. The antenna manufacturer is: Johanson Technology b. Manfacturer part number is: 2450AT18A100 c. Antenna Frequency range is: 2400 - 2500 Mhz d. Specific RF paramaters are as such: Parameter Value Peak gain 0.5 dBi typ. (XZ-V) Average gain -0.5 dBi typ. (XZ-V) Minimum Return Loss 9.5 dB Maximum VSWR 2.3:1 ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 3) Details and photos of V3 antenna: Figure 1 Antenna/Top side of V3 Device WiFi antenna in the upper right ELECTRONIC FLEET MANAGEMENT www.zonarsystems.com ALL INFORMATION CONTAINED HEREIN IS CONFIDENTIAL & PROPRIETARY INFORMATION OF ZONAR SYSTEMS, INC. 18200 Cascade Ave. S. Seattle, WA 98188-4728 Toll-Free 1.877.843.3847 Phone 206.878.2459 Fax 206.878.3082 Figure 2 Close-up of WiFi sub-circuit with antenna in the lower left

Zonar Systems, LLC V3 Report No. ZONA0036.2 Report Prepared By Northwest EMC Inc. NORTHWEST EMC – (888) 364-2378 – www.nwemc.com California – Minnesota – Oregon – New York – Washington 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Evaluation Date of Evaluation: May 29, 2012 Zonar Systems, LLC Model: V3 Emissions Description of Evaluation Specification Evaluation Method Pass/Fail Maximum Permissible Exposure FCC 2.1091:2012 OET Bulletin 65, Supplement C Ed 01-01 Pass Approved By: Don Facteau, IS Manager NVLAP Lab Code: 200630-0 This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Report No. ZONA0036.22 of 10 REV 2012.05.24 REVISION HISTORY Revision Number Description Date Page Number 00 None Report No. ZONA0036.23 of 10 REV 2012.05.24 ACCREDITATIONS AND AUTHORIZATIONS United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC Guide 65 as a product certifier. This allows Northwest EMC to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada IC - Recognized by Industry Canada as a Certification Body (CB). Certification chambers and Open Area Test Sites are filed with IC. European Union European Commission – Validated by the European Commission as a Conformity Assessment Body (CAB) under the EMC directive and as a Notified Body under the R&TTE Directive. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea KCC / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Hong Kong OFTA – Recognized by OFTA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. Russia GOST – Accredited by Certinform VNIINMASH, CERTINFO, SAMTES, and Federal CHEC to perform EMC and Hygienic testing for Information Technology products to GOST standards. SCOPE For details on the Scopes of our Accreditations, please visit: http://www.nwemc.com/accreditations/ Report No. ZONA0036.24 of 10 REV 2012.05.24 LOCATIONS Oregon Labs EV01-EV12 22975 NW Evergreen Pkwy, #400 Hillsboro, OR 97124 (503) 844-4066 California Labs OC01-OC13 41 Tesla Irvine, CA 92618 (949) 861-8918 New York Labs WA01-WA04 4939 Jordan Rd. Elbridge, NY 13060 (315) 685-0796 Minnesota Labs MN01-MN08 9349 W Broadway Ave. Brooklyn Park, MN 55445 (763) 425-2281 Washington Labs SU01-SU07 14128 339 th Ave. SE Sultan, WA 98294 (360) 793-8675 VCCI EV01: C-1071, R-1025, G-84 EV07: C-2687, T-1658 EV11: R-2318 OC06: C-2766, T-1659 OC07: G-548 OC08: R-1943, G-85 OC10: A-0029 MN03: C-3464, T-1634 MN04: R-3125 MN05: G-141 SU01: C-3265, T-1511 SU02: R-871, G-83 Industry Canada 2834D-1, 2834D-2 2834B-1, 2834B-2, 2834B-3 2834E-1 2834C-1 Report No. ZONA0036.25 of 10 Product Description Revision 09/01/11 Client and Equipment Under Test (EUT) Information Company Name: Zonar Systems, LLC Address: 18200 Cascade Ave. S Suite 200 City, State, Zip: Seattle, WA 98188 Test Requested By: David Pascoe Model: V3 Date of Evaluation: May 29, 2012 Information Provided by the Party Requesting the Test Functional Description of the EUT (Equipment Under Test): Vehicle mounted equipment that contains a cellular modem and 802.11b/g/n radio. Objective: To demonstrate compliance with FCC requirements for RF exposure for 2.1091 mobile devices Report No. ZONA0036.26 of 10 WD.12.29.11 Maximum Permissible Exposure (MPE) OVERVIEW Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. ANSI C95.1-1992 specifies a minimum separation distance of 20 cm for performing reliable field measurements to determine adherence to MPE limits. If the minimum separation distance between a transmitter and nearby persons is more than 20 cm under normal operating conditions, compliance with MPE limits may be determined at such distance from the transmitter. When applicable, operation instructions and prominent warning labels may be used to alert the exposed persons to maintain a specified distance from the transmitter or to limit their exposure durations and usage conditions to ensure compliance. If the use of warning labels on a transmitter is not effective or desirable, the alternative of performing SAR evaluation with the device at its closest range to persons under normal operating conditions may be used. The field strength and power density limits adopted by the FCC are based on whole-body averaged exposure and the assumption of RF field levels relate most accurately to estimating whole-body averaged SAR. This means some local values of exposures exceeding the stated field strength and power density limits may not necessarily imply non-compliance if the spatial average of spatially averaged RF fields over the exposed portions of a person’s body doe…

Text truncated - open the document above for the full version.

Zonar Systems, LLC V3 Report #: ZONA0036 Report Prepared By Northwest EMC Inc. NORTHWEST EMC – (888) 364-2378 – www.nwemc.com California – Minnesota – Oregon – New York – Washington 22975 NW Evergreen Parkway Suite 400 Hillsboro, Oregon 97124 Certificate of Test Last Date of Test: May 01, 2012 Zonar Systems, LLC Model: V3 Emissions Test Description Specification Test Method Pass/Fail Effective Radiated Power (ERP) FCC 22H:2012 ANSI/TIA/EIA-603-C-2004 Pass Effective Radiated Power (EIRP) FCC 24E:2012 ANSI/TIA/EIA-603-C-2004 Pass Transmitter Spurious Emissions FCC 22H:2012 ANSI/TIA/EIA-603-C-2004 Pass Transmitter Spurious Emissions FCC 24E:2012 ANSI/TIA/EIA-603-C-2004 Pass Receiver Spurious Emissions FCC 15.109:2012 Class B ANSI C63.4:2009 Pass Deviations From Test Standards None Approved By: Don Facteau, IS Manager NVLAP Lab Code: 200630-0 Test Facility The measurement facility used to collect the data is located at: Northwest EMC, Inc. 22975 NW Evergreen Parkway, Suite 400 Hillsboro, OR 97124 Phone: (503) 844-4066 Fax: 844-3826 This site has been fully described in a report filed with and accepted by the FCC (Federal Communications Commission) and Industry Canada (Site filing #2834D-1). This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government of the United States of America. Product compliance is the responsibility of the client, therefore the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. This Report may only be duplicated in its entirety. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. Revision History Revision 09/01/11 Revision Number Description Date Page Number 00 None Accreditations and Authorizations Revision 02/21/2012 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are liste…

Text truncated - open the document above for the full version.