SG71301HC-CG300CDMA Ix +gsm double mode handset

Copyright©2012 Haier Technologies Co.., Ltd All Rights Reserved Reproduction, transfer, distribution or storage of part or all of the cont ents in this document in any form without the prior written permi ssion as Haier Technologies Co.., Ltd. Statement The contents of this manual maybe different wi th the cell phone please according to the cell phone. Haier reserves the right to revise this documen t or withdraw it at any time without prior notice. Safety Precautions Please read these simple guidelines. Not following them may be dangerous or illegal. For further information, see the section of “Warnings and Precautions”. Do not switch the phone on when Mobile Phone use is prohibited or when it may cause interference or danger. Do not place your phone and its accessories in containers with strong electromagnetic field. Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideratio n while driving should be road safety. Hospitals or health care facilities may be using equipment that could be sensitive to external radio frequency energy. Follow any regulations or rules in force. Do not use the phone at a refueling point. Do not use near fuel or chemicals. Follow any restrictions. Wireless devices can cause interference in aircraft. Keep the phone and all its parts, includi ng accessories, out of the reach of small children. Use only approved batteries and chargers . Disconnect the charger from the power source when it is not in use. Do not leave the battery connected to a charger for more than a week, since overcharging may shorten its lift. Only qualified personnel should service the phone or install the phone in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty applicable to the device. i Contents 1 Getting to Know Your Phone ................................................................................. 1 Basic specif ication ........................................................................................................... 1 Mobile phone appearance ............................................................................................... 1 2 Getting Started ...................................................................................................... 10 Install and charge the phone .......................................................................................... 10 3 Basic Functions ..................................................................................................... 11 Switching On/Off ............................................................................................................ 1 1 Making phone call .......................................................................................................... 11 Answering the call .......................................................................................................... 13 Operations duri ng a call ................................................................................................. 14 Keypad lock ................................................................................................................... 15 4 Text Entry .............................................................................................................. 15 Text input method .......................................................................................................... 15 Change the inpu t method .............................................................................................. 16 5 Cont acts .................................................................................................................... ... 16 ii List .......................................................................................................................... ....... 17 View .......................................................................................................................... ..... 17 Edit .......................................................................................................................... ...... 17 Option ........................................................................................................................ .... 17 Groups settings .............................................................................................................. 18 Speed Dial .................................................................................................................... . 19 6 Messages ................................................................................................................ 19 SMS ........................................................................................................................... .... 20 Voice Mail .................................................................................................................... .. 23 7 Call Hi story ........................................................................................................... 23 All Calls ..................................................................................................................... ..... 23 Missed Ca lls .................................................................................................................. 23 Received Calls ............................................................................................................... 24 Dialed Calls................................................................................................................... . 24 8 Facebook ................................................................................................................ 25 9 Twitter .................................................................................................................... 25 iii 10 Nimbuzz ............................................................................................................... 25 11 UC Browser ................…

Text truncated - open the document above for the full version.

Date: March 6, 2013 Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: SG71301HC-CG300 Dear Sirs: Haier Telecom (Qingdao) Co., Ltd. requests acceptance of the labeling proposal described below for cell phone bearing FCC identifier SG71301HC-CG300. The subject cell phone are compact handheld models as shown in figure 1, authorized under 47CFR Part 22H for CDMA mobile services. Figure 1. Because the majority of the cell phone housing is composed of display, speaker, operating controls and a removable battery pack, there is extremely limited space available to attach the required label carrying the FCC identifier. Attaching the label to the battery pack is not acceptable because the battery pack is a removable item. For this reason, Haier Telecom (Qingdao) Co., Ltd. proposes placing the label carrying the FCC identifier inside the battery compartment as shown in figure 2. Figure 2. The consumer packaging for these models includes the battery pack as a separate item, NOT installed on the radio. As such, the FCC identifier will be readily visible to the user FCC ID Label before the battery pack is installed and whenever the battery pack is removed or replaced. In this location, the label will also be protected from physical abuse and remain readable for the anticipated life of the device. The consumer packaging for these models is a "gift box" which does not allow the transceiver to be seen at time of purchase. In order to meet the requirements of 47CFR Part 2.925 (d), Haier Telecom (Qingdao) Co., Ltd. will add the FCC identifier " SG71301HC-CG300 " to the outside of the consumer "gift box" packaging. Thank you for your attention to this matter. Sincerely Yours, James Shi Type Approval Manager Haier Telecom (Qingdao) Co., Ltd.

Date: March 6, 2013 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern: The Haier Telecom (Qingdao) Co., Ltd. , the undersigned, hereby authorizes Mr. Wu Xuewen from Shenzhen Morlab Communications Technology Co., Ltd., to act on the behalf of the Haier Telecom (Qingdao) Co., Ltd. solely in matters relating to the application for an FCC equipment authorization for FCC ID # SG71301HC-CG300 including the signing of documents in connection with this Application. Necessary acts carried out by Haier Telecom (Qingdao) Co., Ltd. on our behalf of the Haier Telecom (Qingdao) Co., Ltd. in connection with the Application shall have the same effect as acts of the Haier Telecom (Qingdao) Co., Ltd.. The Haier Telecom (Qingdao) Co., Ltd. also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Thank you for your attention to this matter. Sincerely Yours, James Shi Type Approval Manager Haier Telecom (Qingdao) Co., Ltd.

Date: March 6, 2013 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: Haier Telecom (Qingdao) Co., Ltd. FCC ID: SG71301HC-CG300 FCC Part 22H Certification Confidentiality Request Gentlemen: This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material. Haier Telecom (Qingdao) Co., Ltd. requests that the following documents regarding this submission for FCC ID: SG71301HC-CG300 be kept confidential: Exhibit Type File Name Block Diagram Block Diagram.pdf Schematics Schematics.pdf Operational Description Operational description.pdf Part list BOM.pdf Tune-Up-Procedure Tune up procedure.pdf Those documents contain detailed system and equipment description and related information about the product which Haier Telecom (Qingdao) Co., Ltd. considers to be confidential proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, Haier Telecom (Qingdao) Co., Ltd. considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. James Shi Type Approval Manager Haier Telecom (Qingdao) Co., Ltd.

External Photos 1. EUT full view with accessories 2. EUT front view 3. EUT rear view 4. EUT left side view 5. EUT right side view 6. EUT top view 7. EUT bottom view

FCC ID: SG71301HC-CG300 Label Size: 30*15mm Label Location FCC ID Label

Internal Photos 1. EUT uncover view 2. Mainboard front view with shielding 3. Mainboard rear view with shielding 4. Mainboard front view without shielding 5. Mainboard rear view without shielding 6. GSM/CDMA chip view 7. BT chip view 8. GSM/CDMA antenna view 9. BT antenna view 10. LCD screen and keyboard view

SZ13010023S01 Page 2 of 47 DIRECTORY 1. TESTING LABORATORY.........................................................................................................4 1.1. Identification of the Responsible Testing Laboratory................................................................. 4 1.2. Identification of the Responsible Testing Location.....................................................................4 1.3. Accreditation Certificate..............................................................................................................4 1.4. List of Test Equipments...............................................................................................................4 2. TECHNICAL INFORMATION..................................................................................................5 2.1. Identification of Applicant...........................................................................................................5 2.2. Identification of Manufacturer.....................................................................................................5 2.3. Equipment Under Test (EUT)......................................................................................................5 2.3.1. Photographs of the EUT............................................................................................................5 2.3.2. Identification of all used EUT...................................................................................................5 2.4. Applied Reference Documents.................................................................................................... 6 2.5. Device Category and SAR Limits................................................................................................6 2.6. Test Environment/Conditions......................................................................................................7 3. SPECIFIC ABSORPTION RATE (SAR)...................................................................................8 3.1. Introduction..................................................................................................................................8 3.2. SAR Definition............................................................................................................................ 8 4. SAR MEASUREMENT SETUP..................................................................................................9 4.1. The Measurement System............................................................................................................9 4.2. Probe............................................................................................................................................ 9 4.3. Probe Calibration Process..........................................................................................................11 4.3.1 Dosimetric Assessment Procedure...........................................................................................11 4.3.2 Free Space Assessment Procedure...........................................................................................11 4.3.2 Temperature Assessment Procedure........................................................................................11 4.4. Phantom..................................................................................................................................... 12 4.5. Device Holder............................................................................................................................12 5. TISSUE SIMULATING LIQUIDS........................................................................................... 13 6. UNCERTAINTY ASSESSMENT............................................................................................. 15 6.1. UNCERTAINTY EVALUATION FOR EUT SAR TEST....................................................... 15 6.2. UNCERTAINTY FOR SYSTEM PERFORMANCE CHECK................................................ 16 7. SAR MEASUREMENT EVALUATION................................................................................. 18 SZ13010023S01 Page 3 of 47 7.1. System Setup..............................................................................................................................18 7.2. Validation Results......................................................................................................................19 8. OPERATIONAL CONDITIONS DURING TEST..................................................................20 8.1. Informations on the testing........................................................................................................ 20 8.2. Body-worn Configurations........................................................................................................ 21 8.3. Measurement procedure.............................................................................................................21 8.4. Description of interpolation/extrapolation scheme....................................................................22 9. MEASUREMENT OF CONDUCTED PEAK OUTPUT POWER....................................... 23 10. TEST RESULTS LIST.............................................................................................................24 11. MULTIPLE TRANSMITTERS EVALUATION.................................................................. 25 ANNEX A EUT SETUP PHOTOS................................................................................................27 ANNEX B GRAPH TEST RESULTS...........................................................................................31 Change History IssueDateReason for change 1.0Feb. 26, 2013First edition SZ13010023S01 Page 4 of 47 1. Testing Laboratory 1.1. Identification of the Responsible Testing Laboratory Company Name:Shenzhen Morlab Communications Technology Co., Ltd. Department:Morlab Laboratory Address:FL.3, Building A, FeiYang Science Park, No.8 LongChang Roa…

Text truncated - open the document above for the full version.

SZ13010023W02 Page 2 of 77 DIRECTORY 1. GENERAL INFORMATION .................................................................................................... 3 1.1. EUT Description ....................................................................................................................... 3 1.2. Test Standards and Results ........................................................................................................ 4 1.3. Facilities and Accreditations ..................................................................................................... 5 2. 47 CFR PART 15C REQUIREMENTS .................................................................................... 6 2.1. Antenna requirement ................................................................................................................. 6 2.2. Number of Hopping Frequency ................................................................................................ 6 2.3. Peak Output Power.................................................................................................................. 12 2.4. 20dB Bandwidth ..................................................................................................................... 14 2.5. Carried Frequency Separation ................................................................................................. 21 2.6. Time of Occupancy (Dwell time) ........................................................................................... 24 2.7. Conducted Spurious Emissions ............................................................................................... 31 2.8. Band Edge ............................................................................................................................... 38 2.9. Conducted Emission ............................................................................................................... 55 2.10. Radiated Emission................................................................................................................... 58 2.11. RF exposure evaluation ........................................................................................................... 77 Change History Issue Date Reason for change 1.0 February 28, 2013 First edition SZ13010023W02 Page 3 of 77 1. General Information 1.1. EUT Description EUT Type ............................. : CDMA Ix +gsm double mode handset Serial No. .............................. : (n.a, marked #1 by test site) Hardware Version ................. : SP Software Version .................. : Applicant .............................. : Manufacturer ........................ : N.A Qingdao Haier Telecom Co.,Ltd No.1,Haier Road Hi-tech Zone,Qingdao,266101,P.R.China Qingdao Haier Telecom Co.,Ltd No.1,Haier Road Hi-tech Zone,Qingdao,266101,P.R.China Frequency Range .................. : The frequency range used is 2402MHz - 2480MHz (79 channels, at intervals of 1MHz); The frequency block is 2400MHz to 2483.5MHz. Modulation Type .................. : Bluetooth: FHSS (GFSK(1Mbps), ∏/4-DQPSK(EDR 2Mbps), 8-DPSK(EDR 3Mbps)) Antenna Type ........................ : Ceramic antenna Antenna Gain ........................ : 0dBi Note 1: The EUT is a CDMA Ix +gsm double mode handset, it contains Bluetooth Module operating at 2.4GHz ISM band; the frequencies allocated for the Bluetooth Module is F(MHz)=2402+1*n (0<=n<=78). The lowest, middle, highest channel numbers of the Bluetooth Module used and tested in this report are separately 0 (2402MHz), 39 (2441MHz) and 78 (2480MHz). Note 2: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Note 3: a. When power on, the EUT will scan the whole frequency until a Connection command from the other BT devices. b. When receiving the signal from the other BT devices, The EUT transmit aresponse signal. c. The other devices receive the response signal and recognize it, then send a connection command to establish the connection. d. After the connection establish successfully, the data transmission is beginning. At the same time, the both devices will shift frequencies in synchronization per a same pseudo randomly ordered list of hopping frequencies, the hopping rate is1600 times per second. This device conforms to the criteria in FCC Public Notice DA 00-705. e. The bandwidth of the receiver, which is set to a fixed width by the software. Note 4: Bluetooth signal has 9 packages DH1, DH3, DH5, 3DH1, 3DH3, 3DH5, 5DH1, 5DH3, 5DH5, DH5 package is largest, we are testing DH5 in the document. SZ13010023W02 Page 4 of 77 1.2. Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C (Bluetooth, 2.4GHz ISM band radiators) for the EUT FCC ID Certification: No. Identity Document Title 1 47 CFR Part 15 (10-1-09 Edition) Radio Frequency Devices Test detailed items/section required by FCC rules and results are as below: No. Section in CFR 47Description Result 1 15.203 Antenna Requirement PASS 2 15.247(a) Number of Hopping Frequency PASS 3 15.247(b) Peak Output Power PASS 4 15.247(a) 20dB Bandwidth PASS 5 15.247(a) Carrier Frequency Separation PASS 6 15.247(a) Time of Occupancy (Dwell time) PASS 7 15.247(d) Conducted Spurious Emission PASS 8 15.247(d) Band Edge PASS 9 15.207 Conducted Emission PASS 10 15.209 15.247(d) Radiated Emission PASS 11 15.247(i), 1.1307&2.1093 RF exposure evaluation PA S S NOTE: The tests were performed according to the method of measurements prescribed in DA-00-705. SZ13010023W02 Page 5 of 77 1.3. Facilities and Accreditations 1.3.1. Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at…

Text truncated - open the document above for the full version.

Report No.: SZ13010023E01 Page 2 of 16 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1 EUT Description ......................................................................................................................... 3 1.2 Test Standards and Results ........................................................................................................ 4 1.3 Facilities and Accreditations ...................................................................................................... 5 1.3.1 Facilities .................................................................................................................................... 5 1.3.2 Test Environment Conditions .................................................................................................... 5 1.3.3 Measurement Uncertainty ......................................................................................................... 5 2. TEST CONDITIONS SETTING............................................................................................... 6 2.1 Test Mode .................................................................................................................................... 6 2.2 Test Setup and Equipments List ................................................................................................ 7 2.2.1 Conducted Emission.................................................................................................................. 7 2.2.2 Radiated Emission ..................................................................................................................... 8 3. 47 CFR PART 15B REQUIREMENTS .................................................................................. 11 3.1 Conducted Emission ................................................................................................................. 11 3.1.1 Requirement ............................................................................................................................ 11 3.1.2 Test Description ...................................................................................................................... 11 3.1.3 Test Result ............................................................................................................................... 11 3.2 Radiated Emission .................................................................................................................... 13 3.2.1 Requirement ............................................................................................................................ 13 3.2.2 Test Description ...................................................................................................................... 13 3.2.3 Frequency range of measurement ........................................................................................... 13 3.2.4 Test Result ............................................................................................................................... 14 Change History Issue Date Description 1.0 March 7, 2013 First edition Report No.: SZ13010023E01 Page 3 of 16 1. GENERAL INFORMATION 1.1 EUT Description EUT Type ............................. : CDMA 1x + gsm double mode handset Serial No. .............................. : (n.a., marked #1 by test site) Hardware Version ................. : SP Software Version .................. : Applicant .............................. : Manufacturer ........................ : N/A Qingdao Haier Telecom Co., Ltd No.1, Haier Road Hi-tech Zone, Qingdao, 266101, P.R. China Qingdao Haier Telecom Co., Ltd No.1, Haier Road Hi-tech Zone, Qingdao, 266101, P.R. China Power supply ........................ : Battery Brand Name: Haier Model No.: H11169 Serial No.: (n.a. marked #1 by test site) Capacitance: 1000mAh Rated Voltage: 3.7V Charge Limit: 4.2V Ancillary Equipment 1 ......... : AC Adapter (Charger for Battery) Brand Name: Haier Model Name: CYSK05-050055-CE Serial No.: (n.a. marked #1 by test site) Rated Input: 100-240V, 150mA, 50/60Hz Rated Output: 5V, 550mA Speed of the processor .......... : 316MHz (generated by the CPU) 19.20M (generated by the crystal oscillator) Note 1: The EUT is a CDMA Ix + GSM double mode Mobile Phone which is equipped with a USB port which can be connected to the ancillary equipments supplied by the manufacturer e.g. the AC Adapter and the USB Cable. Note 2: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Report No.: SZ13010023E01 Page 4 of 16 1.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart B: No. Identity Document Title 1 47 CFR Part 15 Radio Frequency Devices Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 15.107 Conducted Emission PASS 2 15.109 Radiated Emission PASS NOTE: The tests were performed according to the method of measurements prescribed in ANSI C63.4 2009. Report No.: SZ13010023E01 Page 5 of 16 1.3 Facilities and Accreditations 1.3.1 Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at FL.3, Building A, FeiYang Science Park, No.8 LongChang Road, Block 67, BaoAn District, ShenZhen, GuangDong Province, P. R. China 518101. 1.3.2 Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 15 - 35 Relative Humidity (%): 30 - 60 Atmospheric Pressure (kPa): 86 -106 1.3.3 Measurement Uncertainty The uncertainty is calculated using the methods sug…

Text truncated - open the document above for the full version.

Report No.: SZ13010023W01 Page 2 of 24 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1 EUT Description ......................................................................................................................... 3 1.2 Test Standards and Results ........................................................................................................ 4 1.3 Facilities and Accreditations ...................................................................................................... 5 2. 47 CFR PART 2, PART 22H REQUIREMENTS .................................................................... 6 2.1 Conducted RF Output Power .................................................................................................... 6 2.2 99% Occupied Bandwidth ......................................................................................................... 9 2.3 Frequency Stability ................................................................................................................... 12 …

Text truncated - open the document above for the full version.