SJC-M1020EVM900 MHz Hopping System

Dust Networks D1120 Evaluation Kit Quick Start Guide D1120 EVALUATION KIT QUICK START GUIDE Trademarks Dust Networks, the Dust Networks logo, and SmartMesh are trademarks of Dust Networks, Inc. All third party brand and product names are the trademarks of their respective owners and are used solely for informational purposes. Copyright This documentation is protected by United States and international copyright and other intellectual and industrial property laws. It is solely owned byDust Networks, Inc. and its licensors and is distributed under a restrictive license. This product, or any portion thereof, may not be used, copied, modified, reverse assembled, reverse compiled, reverse engineered, distributed or redistributed in any form by any means without the prior written authorization of Dust Networks, Inc. RESTRICTED RIGHTS: Use, duplication, or disclosure by the U.S. Government is subject to restrictions of FAR 52.227-14(g) (2)(6/87) and FAR 52.227-19(6/87), or DFAR 252.227-7015 (b)(6/95) and DFAR 227.7202-3(a) and any and all similar and successor legislation and regulation. Disclaimer THIS DOCUMENTATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS DOCUMENTATION MIGHT INCLUDE TECHNICAL INACCURACIES OR OTHER ERRORS. CORRECTIONS AND IMPROVEMENTS MIGHT BE INCORPORATED IN NEW VERSIONS OF THE DOCUMENTATION. EMI Warning This equipment has been tested and found to comply with the limits pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio or television technician for assistance. Contents D1120 EVALUATION KIT QUICK START GUIDEi 1 About This Guide Related Documents.......................................................................... iii Conventions Used.............................................................................. iii 1 M1020 Evaluation Module M1020 Evaluation Module........................................................... 1 Connector P1.......................................................................................... 2 Connector P2.......................................................................................... 3 Serial Interface.................................................................................... 4 Power Supply......................................................................................... 4 Absolute Maximum Ratings........................................................ 4 Recommended Operating Conditions................................. 5 Wireless Specifications.................................................................. 5 Antenna...................................................................................................... 5 Regulatory Information................................................................ 6 2 SmartMesh Manager Description............................................................................................... 7 Connections............................................................................................. 8 Technical Specifications................................................................ 8 Regulatory Information................................................................ 9 3 Setting Up a Network Setting Up the SmartMesh Manager................................. 11 Setting Up the Network............................................................... 11 TABLE OF CONTENTS iiD1120 EVALUATION KIT QUICK START GUIDE D1120 EVALUATION KIT QUICK START GUIDEiii About This Guide This guide provides information required to successfully demonstrate the capabilities of the D1100 Evaulation Kit. It provides various pinout and connector information for attaching sensors to a mote Evaluation Module and instructions for setting up a network. Related Documents The following documents are available for a SmartMesh Network: •D1120 Evaluation Kit Quick Start Guide (this guide) •SmartMesh Manager Application Programming Interface (API) Guide •M1020 Mote Integration Guide •SmartMesh Network Planning Guide •SmartMesh Network Administration Guide Conventions Used The following conventions are used in this guide: •Computer type indicates information that you enter, such as specifying a URL. •Bold type indicates buttons, fields, and menu commands. •Italic type is used to introduce a new term. dNote: Notes provide more detailed information about concepts. bCautions: Cautions advise you about actions that might result in a loss of data. cWarning! Warnings advise you about actions that may cause physical harm to the hardware or your person. CHAPTER 1 - ABOUT THIS GUIDEConventions Used ivD1120 EVALUATION KIT QUICK START GUIDE Body. D1120 EVALUATION KIT QUICK START GUIDE1 1 M1020 Evaluation Module This chapter provides specifications for the M1020 Evaluation Module (M1020-EVM) provided in the D1120 Evaluation Kit. The M1020-EVM can be used as a reference design for integrating an M1020 Mote into a self-contained device. M1020 Evaluation Module The M1020-EVM consist…

Text truncated - open the document above for the full version.

2560 Ninth Street, Suite 220 Berkeley, California 94710 www.dustnetworks.com April 7, 2005 Bay Area Compliance Laboratory Corp. 230 Commercial Street Sunnyvale, CA 94085 Re: Confidentiality of FCC Filings Dear Sir/Madam, We, Dust Networks, Inc. request that you file the appropriate paperwork requesting for confidentiality of the data contained in the applications for the following project(s): SmartMesh™ Manager - D1120 M1020 Mote Evaluation Module - M1020EVM Specifically, we would like any documents that contain schematics, block diagrams, circuit descriptions, technical specifications, or any other data that can be maintained confidential under FCC rules. Sincerely, Jeffery D. Fitch Director, Customer Support Dust Networks, Inc.

EXHIBIT C - EUT EXTERNAL PHOTOGRAPHS Chassis Front View Chassis Rear View

EXHIBIT A - FCC ID LABEL INFORMATION Proposed FCC ID Label Specifications: Text is black or white in color and is left justified. Labels are silk- screened and shall be “permanently affixed” at a conspicuous location on the EUT. Proposed Label Location on EUT Chassis Rear View/FCC ID Label FCC ID: SJC-M1020EVM This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.1875" 1.0" FCC ID: SJC-M1020EVM This device complies with Part 15 of the FCC Rl Oti ibj tt

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Chassis Cover off View EUT Component View EUT Solder View TX Component View TX Solder View

Note: This test report is specially limited to the above client company and product model only. It may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the U.S. Government. FCC PART 15.247 EMI MEASUREMENT AND TEST REPORT For Dust Networks, Inc. 30695 Huntwood Ave. Hayward, CA 94544 FCC ID: SJC-M1020EVM This Report Concerns: Original Report Equipment Type: 900 MHz Hopping System Test Engineer: Snell Leong Report No.: R0504082 Report Date: 2005-04-21 Reviewed By: Richard Lee Prepared By: Bay Area Compliance Laboratory Corporation (BACL) 230 Commercial Street Sunnyvale, CA 94085 Tel: (408) 732-9162 Fax: (408) 732 9164 Dust Networks, Inc. FCC ID: SJC-M1020EVM Report # R0504082Rpt-bRpt Page 2 of 35 FCC Part 15.247 Test Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................................................4 OBJECTIVE...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................4 TEST METHODOLOGY..................................................................................................................................................4 TEST FACILITY.............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 JUSTIFICATION.............................................................................................................................................................5 SPECIAL ACCESSORIES.................................................................................................................................................5 SCHEMATICS / BLOCK DIAGRAM.................................................................................................................................5 EQUIPMENT MODIFICATIONS.......................................................................................................................................5 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS........................................................................................................5 EXTERNAL I/O CABLING LIST AND DETAILS...............................................................................................................5 CONFIGURATION OF TEST SYSTEM..............................................................................................................................6 SUMMARY OF TEST RESULTS FOR FCC PART 15............................................................................................7 ANTENNA REQUIREMENT ......................................................................................................................................8 §15.207(A) - CONDUCTED EMISSION.....................................................................................................................9 §15.205 & §15.209 - RADIATED EMISSION...........................................................................................................10 MEASUREMENT UNCERTAINTY..................................................................................................................................10 TEST SETUP................................................................................................................................................................10 SPECTRUM ANALYZER SETUP....................................................................................................................................10 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................10 ENVIRONMENTAL CONDITIONS..................................................................................................................................11 TEST PROCEDURE......................................................................................................................................................11 CORRECTED AMPLITUDE & MARGIN CALCULATION.................................................................................................11 SUMMARY OF TEST RESULTS.....................................................................................................................................11 3 METERS RADIATED EMISSION TEST DATA..............................................................................................................12 3 METERS RADIATED EMISSION TEST DATA (CONT.) ................................................................................................13 §15.247 (A) (1) - HOPPING CHANNEL SEPARATION ........................................................................................15 STANDARD APPLICABLE............................................................................................................................................15 MEASUREMENT PROCEDURE......................................................................................................................................15 TEST EQUIPMENT.......................................................................................................................................................15 ENVIRONMENTAL CONDITIONS.................................................................…

Text truncated - open the document above for the full version.

EXHIBIT B - TEST SETUP PHOTOGRAPHS Radiated Emission - Front View Radiated Emission - Rear View