SQD-6220CSU-ABGWLAN Cable Access Point 6220

Nortel Networks WLAN Cable Access Point 6220 Release 2.0 CSU User Guide Standard Release 2.0 Issue 1 Dec 2005 What’s inside? About this document Overview Planning your WLAN network Installation Configuration Administration Troubleshooting Appendix NTPM99CA 2 Copyright © 2005 Nortel Networks All rights reserved. July 2005. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Nortel Networks and the Nortel Networks logo are trademarks of Nortel Networks, Inc. Multi-Region Product Documentation This document may describe features that are not available in your region due to local regulations. Compliances Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: . • Reorient the receiving antenna . • Increase the separation between the equipment and receiver . • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected . • Consult the dealer or an experienced radio/TV technician for help FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The transmitted power of the APU and CSU does not exceed 36 dBm. 3 Publication history December 2005 Issue 1. Issued for WLAN Cable Access Point 6220 CSU 5 Contents ABOUT THIS DOCUMENT 7 OVERVIEW 13 I NTRODUCTION 13 P RODUCT DESCRIPTION 15 CSU (CORPORATE SERVICE UNIT) 17 PLANNING YOUR WLAN NETWORK 21 S ITE SURVEY & PLANNING 22 W IRELESS NETWORK PLANNING 23 INSTALLATION 25 CSU INSTALLATION & CONFIGURATION 25 P ROCEDURE 1-1 28 P ROCEDURE 1-2 30 CONFIGURATION 33 S OFTWARE INSTALLATION (AP CONFIGURATOR) 34 P ROCEDURE 3-1 36 P ROCEDURE 3-2 44 P ROCEDURE 3-3 52 P ROCEDURE 3-4 61 P ROCEDURE 3-5 63 P ROCEDURE 3-6 98 ADMINISTRATION 141 S AVING CONFIGURATION 142 L OADING NEW CONFIGURATION 143 UPLOADING SOFTWARE 144 REBOOTING A REMOTE STATION 151 TROUBLESHOOTING 153 APPENDIX A. SPECIFICATION 159 GENERAL ET-PR12 BUILT-IN PANEL ANTENNA RF FILTER PROTECTOR APPENDIX B. ENCLOSURE DIMENSION 164 APPENDIX C. SITE SURVEY 165 5 WLAN Cable Access Point 6220 CSU NTPM99CA Rel 2.0 Issue 1 Dec 2005 7 About this document This document describes the system features used in the WLAN Cable Access Point 6220 Release 2.0 Product. Topics covered include the following: • Overview Introduction Product Description CSU (Corporate Services Unit) • System Planning Site Survey & Planning Wireless Network Designing • Installation CSU Hardware Installation • Configuration CSU in Secure Data Mode (P2P, P2M) Testing Connection between CSU (APU mode) and CSU • Advanced Configuration System Administration Tasks Save configuration Edit configuration Load new configuration Upload new license • Troubleshooting 7 WLAN Cable Access Point 6220 CSU NTPM99CA Rel 2.0 Issue 1 Dec 2005 Audience The intended audience for this document includes: • Installers • Technicians • Nnetwork planners • Network & system engineers • Network administrators List of Abbreviations AP Access Point APU Access Point Unit ARP Address Resolution Protocol BPDU Bridge Protocol Data Unit BPSK Binary Phase-Shift Keying CATV Community Antenna Television CM Cable Modem CMTS Cable Modem Termination System CPE Customer Premises Equipment CSU Corporate Service Unit DBPSK Differential Binary Phase-Shift Keying DHCP Dynamic Host Configuration Protocol DOCSIS Data Over Cable Service Interface Specifications DQPSK Differential Quadrature Phase Shift Keying DVM Digital Volt Ohm Meter EAP Extensible Authentication Protocol EIRP Equivalent Isotropic Radiated Power EMI Electromagnetic Interference FCC Federal Communications Commission FCS Frame Check Sequence FTP File Transfer Protocol HFC Hybrid Fiber Coax ICMP Internet Control Message Protocol IEEE Institute of Electrical and Electronics Engineers ISM Industrial Scientific and Medical equipment ISP Internet Service Provider ITU International Telecommunication Union LOS Line of Sight MAC Media Access Control MIB Management Information Base NAS Network Access Server NAT Network Address Translation 8 WLAN Cable Access Point 6220 CSU NTPM99CA Rel 2.0 Issue 1 Dec 2005 NLOS Non Line of Sight NMS Network Management System NWID Network ID OLOS Optical Line of Sight ONU Optical Network Unit PCMCIA Personal Computer Memory Card International Association PI Power Inserter POE Power over Ethernet PSU Power Supply …

Text truncated - open the document above for the full version.

MTI Co., LTD 166-10 Karak-dong, Songpa-ku Seoul, Korea 138-810 Tel : +82-2-421-4042 Fax: +82-2-421-4043 URL: www.mtico.co.kr Date: November 17, 2005 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, MTI Co., Ltd would like to declare that this device, FCC ID: SQD-6220CSU-ABG does not operate at 5150-5350 MHz and support turbo mode at 802.11a/g mode, because we block these functions by firmware. So user cannot control and operate above frequency and mode by software. Sincerely Yours, H. S. Byun / Director MTI Co., Ltd. TEL: +82-2-421-4042 (206) FAX: +82-2-404-4043

EEPROM WMIA-123AG BLOCK DIAGRAM Diplexer / LPF Voltage Regulator U1 AR5213 VR1 / 2.5V U2 AT93C86 U3 AR5112 printed circuit S1 MASWSS0094 D1 SMS7621 printed circuit PCI interface Configurtion PLL MAC Digital PHY ADC ADC DAC DAC DC +3.3V +3.3V +2.5V LTC3406 +3.3V +3.3V +1.8V Crystal 40MHz Y2 KSS CX-96F-40.000 +3.3V +2.5V Bias / Control Transmitter Receiver Synthesizer Phase Frequency Detector Charge Pump VCO loop Filter ( on-chip) 40MHz ref. clock divider Channel Select 5GHz RF Mixer 2.4GHz RF Mixer IF Mixer Reconstructi on Filter I Q Power Amplifier IF Mixer 5GHz RF Mixer 2.4GHz RF Mixer Q I Baesband Programmable gain filter LNA Control signals QI divider 5GHz XLAN 2.4GHz XPA 5GHz XPA 5GHz Balun 2.4 /5 GHz DPDT RF Switch 2.4/ 5 GHz Coupler 5GHz LPF 2.4GHz BPF Diplexer ( discrete ) Auto loop control antenna diversity 2.4/5 GHz power detector +3.3V Tx Rx termination termination +2.5V +3.3V +3.3V F1 HHM1562B U6 LX5506 U5 LX5510 F6 MDR880J Q4 SGA-8343 11b RF_LO IF_LO 2412 1740 672 2417 1745 672 2422 1750 672 2427 1755 672 2432 1760 672 2437 1765 672 2442 1770 672 2447 1775 672 2452 1780 672 2457 1785 672 2462 1790 672 2467 1795 672 2472 1800 672 2484 1780 704 5112 unit : MHz 5112 11a RF_LO IF_LO 5170 3446.667 1723.3335190 3460 1730 5210 3473.333 1736.6675230 3486.667 1743.333 unit : MHz ANT A ANT B Voltage Regulator VR2 / 1.8V AME8805MEFT +1.8V F8 MDR767F Mini-PCI interface termination UFL_CON UFL_CON 2G_RX_BPF

ONETECH Corp. http://www.onetech.co.kr 505 SK APT Factory, 223-28 Sangdaewon 1-Dong, Jungwon-Gu, Seongnam-City, Kyunggi-Do 462-121, Korea [ Tel ] 82-31-746-8500, [ Fax ] 82-31-746-8700 ONETECH November 4, 2005 FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Attention: Application Examiner Reviewing Engineer Re: Request for confidentiality per Section 0.459 of FCC Rules Applicant: MTI Co., Ltd FCC ID: SQD-6220CSU-ABG To whom it may concern, Request is hereby submitted, on behalf of my client, Bluebird Soft Inc., to withhold from public review certain portions of the application for equipment certification for the referenced FCC identifier. In particular, the following sections of the application and report are requested to be kept confidential: All Schematics Rationale for request for confidentiality: Bluebird Soft Inc. has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the confidential portions of this application to competitors would give them competitive advantage in developing similar products. If you have questions or need further information, please contact the undersigned. Sincerely, Y.K. Kwon / Director Onetech Corp. Email: [email protected]

MTI Co., LTD 166-10 Karak-dong, Songpa-ku Seoul, Korea 138-810 Tel : +82-2-421-4042 Fax: +82-2-421-4043 URL: www.mtico.co.kr Date: October 25, 2005 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, the undersigned, hereby authorize Onetech Corp., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Onetech Corp. on our behalf shall have the same effect as acts of our own. In authorizing Onetech Corp. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, H. S. Byun / Director MTI Co., Ltd. TEL: +82-2-421-4042 (206) FAX: +82-2-404-4043

1 Helen Zhao Subject: FW: MTI Co., LTd, FCC ID: SQD-6220CSU-ABG, Assessment NO.: AN05T5298, Notice#1 6220CSU_Report.d oc 6220CSU_Manual.p df > Dear Helen, > > Thank you for your kind and quick response. > > I would like to answer your questions as following step by step. > > Answer #1 I completed upload your requesting documents except for revised test report and manual. > > Answer #2 Enclosed please find original module test report, block diagram for system and authorization letter. > > Answer #3 & 4 The EUT should be use same Gemtek RF Module, but the EUT shall not operate at 5150-5350MHz because the firmware in the EUT block this frequency band and turbo mode function. Attached please find a declaration letter issued by MTI. > > Answer #5 Attached please find revised test report > > Answer# 6 Please refer to page 2 in the revised user manual. > > Answer# 7 I will send revised manual to you after getting that from our client, MTI. > > Best regards, > > Y. G. Gwon > >>> -----Original Message----- >> From: Compliance Certification Services [mailto:[email protected]] >> Sent: Wednesday, November 16, 2005 4:00 PM >> Subject: MTI Co., LTd, FCC ID: SQD-6220CSU-ABG, Assessment NO.: >> AN05T5298, Notice#1 >> >> >> Question #1: Please create a new application for UNII portion. >> >> Question #2: This application will be treated for DTS portion only. Please submit the following missing documents: >> >> Block Diagram - System >> Test Report - antenna conducted port test >> Agency Authorization Letter >> >> Question #3: The test report indicates the device uses a certified module FCC ID: MXF-M930907. But the certified module has the capability to operate at 5150-5350MHz, the test report and application form indicate this band is disabled. Please explain whether there is any difference between the module that were installed in the device and the certified module. What kind of change(s) have been made? Software, 2 firmware, hardware? If necessary, please submit the support documents. >> >> Question #4: The original certified module supports turbo mode: g turbo: 2437MHz, a turbo: 5760MHz and 5800MHz. But the test report in the filing, which is for radiated emission test, does not indicate turbo mode has ever been evaluated. Please resubmit turbo mode test data. >> >> Question #5: The test report section 7.6.1.1 & 7.7.1.1 Restricted Bandedge test, please resubmit plots to show entire 2310-2390MHz band, 50MHz span with center frequency 2400MHz is not enough to show compliance. >> >> Question #6: The user manual does not include enough RF exposure statements, please add the following statement into the manual: >> >> The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. >> >> Question #7: Please add 802.11b/g portion into the user manual. >> >> Best Regards, >> Helen Zhao >> >> >> The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. Enclosure with 2 GHz Antenna FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. Enclosure with 5 GHz Antenna FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab.

FCC ID.: SQD-6220CSU-ABG File No.: E05NR-010 ONETECH Testing & Evaluation Lab. IDENTIFICATION LABEL: PROPOSED FCC ID LABEL The label included following statement will be attached on the bottom side of product. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. Made in Korea FCC ID : SQD-6220CSU-ABG FCC ID AREA

FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. 5 GHz Antenna FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. 2 GHz Antenna FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab. FCC ID.: SQD-6220CSU-ABG File No. : E05NR-010 ONETECH Testing & Evaluation Lab.

1. Introduction The WMIA-123AG is a mini PCI solution for IEEE 802.11a/b/g wireless LAN. With 802.11b mode, it provides data rates of 1, 2, 5.5, and 11Mbps, supporting IEEE 802.11b network specification for Direct Sequence Spread Spectrum (DSSS) signaling. With 802.11a mode, it implements a half-duplex, orthogonal frequency division multiplexing (OFDM) technology supporting all IEEE 802.11a data rates (6 to 54Mbps). 802.11g mode is also provided to support 1 to 54Mbps with DSSS or OFDM technology. This card is a good solution for users who need mini PCI 802.11a/b/g WLAN functionality. 1.1. Product Features - High speed for wireless LAN connection: IEEE802.11b 11Mbps data rate by incorporating Direct Sequence Spread Spectrum (DSSS); IEEE802.11a 54Mbps data rate with Orthogonal Frequency Division Multiplexing (OFDM) and up to 108Mbps with Turbo mode; IEEE802.11g 54Mbps date rate with OFDM (108Mbps in Turbo mode) and 11Mbps with DSSS. Provide seamless roaming within the IEEE 802.11a/b WLAN infrastructure - IEEE 802.11a/b/g compatible: allowing inter-operation among multiple vendors - Support Wake on LAN (subject to software) - 64-bit, 128-bit, or 152-bit WEP encryption, set by ASCII and Hexadecimal mode - Smart selection function - Mini PCI type IIIB form factor - Site survey function. - Hardware Radio on/off function - Support MicroSoft Windows XP, 2000, ME, and 98SE - Interoperability – Complying with WiFi - WPA, WPA-PSK - Super A/G. 2. Hardware Architecture 2.1 Main Chipset Information 2.1.1 MAC/Baseband Processor The Atheros AR5213 is part of the AR5004 solutions for 5GHz and 2.4GHz wireless local area networks. The AR5213 integrates multi-protocol media access control, a baseband processor, a PCI/Cardbus host interface, analog-to-digital, and digital-to- analog converters. 2.1.2 5GHz Radio Transceiver The AR5112 chip is an integrated CMOS radio transceiver that supports the IEEE 802.11a, 802.11b, and 802.11g standard. The chip supports connection to an external output booster for higher performance. 2.2 Antenna Connector Two antenna connectors (HRS U.FL-R-SMT) are provided to support antenna diversity. 2.3 LED Function 2.4 Radio On/Off Mechanism Suggestion: Note: The value of R82 and R85 is 187 ohm. The value of R0 and R1 is user defined for LED current limitation.

MAXIMUM PERMISSIBLE EXPOSURE RF Exposure Calculation According to the FCC rule 1.1310 table 1B, the limit for the maximum permissible RF exposure for an uncontrolled environment is 1mW/cm². The electric field generated for a 1mW/cm²exposure is calculated as follows: E = √ (30 * P * G) / d, and S = E² / Z = E² / 3770, because 1mW/ cm² = 10W/m² Where S = Power density in mW/cm², Z = Impedance of free space, 377Ω E = Electric filed strength in Volts/m, G = Numeric antenna gain, and d = distance in meter Combing equations and rearranging the terms to express the distance as a function of the remaining variable d = √ (30*P*G) / (3770 *S) Changing to units of mW and cm, using P (mW) = P (W) / 1000, d (cm) = 100 * d (m) d = 0.282 * √ (P*G) / S Where d = distance in cm, P = Power in mW, G = Numeric antenna gain, and S = Power density in mW/cm² Calculated MPE Safe Distance According to above equation, the following result was obtained. Peak Output Power Antenna Gain Operating Mode (dBm) (mW) dBi Calculated RF Exposure Separation Distance (cm) 802.11b 16.2 41.687 12.0 7.25 802.11g 14.2 26.303 12.0 5.76 802.11a 12.0 16.069 12.0 4.50 Remark The numeric antenna gain for the EUT is 15.85.

Page 1 of 40 FCC ID. : SQD-6220CSU-ABG File No. : E05NR-010 It should not be reproduced except in full, without the written approval of ONETECH. EMC-007(Rev.0) HEAD OFFICE : #505 SK APT. Factory 223-28, Sangdaewon 1 Dong, Jungwon-Gu, Seongnam-City, Kyunggi-Do, 462-121, Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 426-1 Daessangryung-Ri, Chowol-Myun, Kwangju-Kun, Kyunggi-Do 464-860 Korea. (TEL: 82-31-765-8289 FAX: 82-31-766-2904) ONETECH Testing & Evaluation Lab. ELECTROMAGNETIC EMISSION C OMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test report file number : E05NR-010 Applicant : M T I C o . , L t d . Address : 166-10 Garak-dong, Songpa-gu, Seoul Korea Manufacturer : M T I C o . , L t d . Address : 166-10 Garak-dong, Songpa-gu, Seoul Korea Type of Equipment : WLAN Cable Access Point FCC ID. : SQD-6220CSU-ABG Model Name : WLAN Cable Access Point 6220-CSU Serial number : None Total page of Report : 40 pages (including this page) Date of Incoming : August 27, 2004 Date of issue : November 7, 2005 SUMMARY The equipment complies with the regulation; FCC Part 15 Subpart C Section 15.247 and Subpart E. This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Prepared by: Reviewed by: Young-Min, Choi / Senior Engineer Y. K. Kwon / Director EMC Div. EMC Div. ONETECH Corp. ONETECH Corp. Page 2 of 40 FCC ID. : SQD-6220CSU-ABG File No. : E05NR-010 It should not be reproduced except in full, without the written approval of ONETECH. EMC-007(Rev.0) HEAD OFFICE : #505 SK APT. Factory 223-28, Sangdaewon 1 Dong, Jungwon-Gu, Seongnam-City, Kyunggi-Do, 462-121, Korea (TEL: 82-31-746-8500 FAX: 82-31-746-8700) EMC Testing Dept : 426-1 Daessangryung-Ri, Chowol-Myun, Kwangju-Kun, Kyunggi-Do 464-860 Korea. (TEL: 82-31-765-8289 FAX: 82-31-766-2904) ONETECH Testing & Evaluation Lab. CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE .............................................................................................4 2. TEST SUMMARY ..............................................................................................................................5 2.1 TEST ITEMS AND RESULTS..............................................................................................................................................5 2.2 ADDITIONS, DEVIATIONS, EXCLUSIONS FROM STANDARDS...........................................................................................5 2.3 RELATED SUBMITTAL(S) / GRANT(S)............................................................................................................................5 2.4 PURPOSE OF THE TEST...................................................................................................................................................6 2.5 TEST METHODOLOGY....................................................................................................................................................6 2.6 TEST FACILITY...............................................................................................................................................................6 3. GENERAL INFORMATION ............................................................................................................7 3.1 PRODUCT DESCRIPTION.................................................................................................................................................7 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT.................................................................7 4. EUT MODIFICATIONS ....................................................................................................................7 5. SYSTEM TEST CONFIGURATION ...............................................................................................8 5.1 JUSTIFICATION...............................................................................................................................................................8 5.3 PERIPHERAL EQUIPMENT...............................................................................................................................................8 5.4 MODE OF OPERATION DURING THE TEST.......................................................................................................................8 5.5 CONFIGURATION OF TEST SYSTEM...............................................................................................................................9 5.6 ANTENNA REQUIREMENT..............................................................................................................................................9 6. PRELIMINARY TEST ....................................................................................................................10 6.1 AC POWER LINE CONDUCTED EMISSIONS TESTS.......................................................................................................10 6.2 GENERAL RADIATED EMISSIONS TESTS......................................................................................................................10 7. 100 KHZ BANDWIDTH OUTSIDE THE FREQUENCY BAND ...............................................11 7.1 OPERATING ENVIRONMENT.........................................................................................................................................11 7.2 TEST SET-UP FOR CONDUCTED MEASUREMENT..........................................................................................................11 7.3 TEST DATA....................................................................................................................................................................11 7.4 TEST SET-UP FOR RADIATED MEASUREMENT..............................................................................................................11 7.5 TEST EQUIPMENT USED…

Text truncated - open the document above for the full version.

FCC ID: MXF-M930907 Report No.: RF930909L111Issued: Sep. 20, 2004 FCC TEST REPORT REPORT NO.: RF930909L11 MODEL NO.: WMIA-123AG RECEIVED: Aug. 16, 2004 TESTED: Aug. 16 ~ Aug. 19, 2004 APPLICANT: Gemtek Technology Co., Ltd. ADDRESS: No.1, Jen Ai Road, Hsinchu lndustrial Park, Hukou Hsinchu 303, Taiwan, R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: 47 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 173 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: MXF-M930907 Report No.: RF930909L112Issued: Sep. 20, 2004 Table of Contents 1.CERTIFICATION ......................................................................................... 5 2.SUMMARY OF TEST RESULTS................................................................. 6 2.1 MEASUREMENT UNCERTAINTY............................................................... 8 3.GENERAL INFORMATION ......................................................................... 9 3.1GENERAL DESCRIPTION OF EUT ........................................................... 9 3.2DESCRIPTION OF TEST MODES ........................................................... 10 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ........................... 11 3.4DESCRIPTION OF SUPPORT UNITS...................................................... 12 3.5CONFIGURATION OF SYSTEM UNDER TEST....................................... 12 4.TEST TYPES AND RESULTS (FOR PART 802.11b & 802.11g) ............... 13 4.1CONDUCTED EMISSION MEASUREMENT ............................................ 13 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT ......................... 13 4.1.2TEST INSTRUMENTS .............................................................................. 13 4.1.3TEST PROCEDURES............................................................................... 14 4.1.4DEVIATION FROM TEST STANDARD ..................................................... 14 4.1.5TEST SETUP ............................................................................................ 15 4.1.6EUT OPERATING CONDITIONS.............................................................. 15 4.1.7TEST RESULTS........................................................................................ 16 4.2RADIATED EMISSION MEASUREMENT ................................................. 22 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT .............................. 22 4.2.2TEST INSTRUMENTS .............................................................................. 23 4.2.3TEST PROCEDURES............................................................................... 24 4.2.4DEVIATION FROM TEST STANDARD ..................................................... 24 4.2.5TEST SETUP ............................................................................................ 25 4.2.6EUT OPERATING CONDITIONS.............................................................. 25 4.2.7TEST RESULTS........................................................................................ 26 4.36dB BANDWIDTH MEASUREMENT ....................................…

Text truncated - open the document above for the full version.