STZSRP9170UWUHF PORTABLE TRANSCEIVER

SRP9180 / SRP9170 P25 Portable Radio P25 User Manual TNM-U-E-0091 V1.4a August 2009 SRP9170/80 P25 Portable Radio – User Manual © ComGroup Australia 2010 Page 2 TNM-U-E-0091 1.4a Associated Documentation The following documentation is available for use with the SRP9180 series of products: TNM-U-E-0088 SRP9180 PMR Brief User Guide TNM-U-E-0089 SRP9180 PMR User Manual TNM-U-E-0090 SRP9180 MPT1327 User Manual TNM-U-E-0095 SRP9180 P25 Brief User Guide TNM-U-E-0102 SRP9180 Brief User Guide (General) To order copies of any of the above publications, or any other Simoco product, contact Comgroup Australia on +61 3 9730 3800 or send a Fax on +61 3 9730 3968. The Simoco web site also has a comprehensive list of documentation available for download. www.simoco.com.au About This Document This publication is copyright and no part may be reproduced without prior permission of ComGroup Australia. Due to our policy of continuous improvement to our products and services, technical specifications and claims, correct at time of publication, may be subject to variation without prior notice. ComGroup Australia has endeavoured to ensure that the information in this document is fairly and accurately stated, but does not accept liability for any errors or omissions. Conventions Where the word “generally” or “may” is used to describe a facility, this operation is an option that may be enabled with the FPP. In some cases, key functions will be determined by the customer configuration, so when a key function is referred to in these instructions, the function may be assigned to another physical location than designated here. References to the SRP9180 also apply to the non-keypad version (SRP9170) except where keypad operation is described. SRP9170/80 P25 Portable Radio – User Manual © ComGroup Australia 2010 Page 3 TNM-U-E-0091 1.4a General Safety 1. Do not operate your portable radio, without a handsfree kit, whilst driving a vehicle. 2. Do not operate your radio in an explosive atmosphere – unless the radio’s level of IECEx approval is approved for use in that atmosphere. Obey the 'Turn Off Two-way Radios' signs where these are posted, e.g. on a petrol station forecourt. 3. Do not dispose of batteries in a fire. IECEx Intrinsically Safe Radios Radio models approved for use in hazardous environments according to the IECEx Scheme are marked with an approval number. Refer to the label on the radio for the IECEx compliance level. The following MUST be observed to maintain the IECEx protection rating: • Use only approved SIMOCO battery, part number PAR-9180BATL2i or PAR-9180BATL3i . • Battery charging must only be carried out in non-hazardous areas, using an approved battery charger. • Metal belt clips must NOT be used in hazardous areas. • It is a requirement that when the radio is used in a hazardous area that either the SRP9180 Accessory Cover Assy (6102 350 1446) or an approved Simoco IECEx accessory is fitted (refer Section 7 for list of approved accessories). • Approved accessories may only be connected and disconnected outside hazardous areas. • Prior to use in a hazardous area, inspect the radio and accessories for signs of damage. Any visible signs of damage to the radio or accessories may compromise the integrity and safety of the radio. A damaged radio or accessories must be repaired or replaced prior to use in a hazardous area. • Incorrect storage, handling or operation of the radio and accessories, as specified in Simoco published User Guides and Service Manuals, may compromise the safety and integrity of the radio and/or accessories. • Approved labels stating the IECEx rating level must be on the radio and accessories, and be legible, before their use in a hazardous area. • Servicing and upgrades of IECEx approved Intrinsically Safe radios and accessories must only be carried out by Simoco IECEx Intrinsically Safe trained staff, at locations that have been IECEx approved. Please contact the Simoco Help Desk on 1300 363 607 for your nearest approved Service Department. • Substitution of parts or accessories will void the equipments’ IECEx Intrinsic Safety rating. SRP9170/80 P25 Portable Radio – User Manual © ComGroup Australia 2010 Page 4 TNM-U-E-0091 1.4a Hints for Using the Radio  When transmitting, hold the radio a few centimetres from your mouth and speak across it, rather than into it. The microphone is located near the bottom right hand corner of the portable radio’s speaker grille.  Keep the length of your conversation to a minimum to conserve battery life.  When it is possible to move location, avoid making calls from known poor signal-strength areas such as the radio systems fringe areas (limit of range) or from screened or shadowed areas, e.g. an underground car park or underpass. SRP9170/80 P25 Portable Radio – User Manual © ComGroup Australia 2010 Page 5 TNM-U-E-0091 1.4a CONTENTS 1 INTRODUCTION ................................................................................................. 8 1.1 Overview...................................................................................................... 8 1.2 Configuration .............................................................................................. 8 1.3 Modes of SRP9180 P25 Operation ............................................................ 8 2 CONTROLS......................................................................................................... 9 3 MENU SYSTEM................................................................................................. 11 3.1 Menu Navigation ....................................................................................... 12 4 MENU SCREENS .............................................................................................. 14 4.1 Channel Screen......................................................................................... 14 4.2 Menus........................................................................................................ 16 4…

Text truncated - open the document above for the full version.

Form Number: FN0024_0 Page 1 of 1 Filename: H:\Standards\FCC\SRP9180_FCC_IC\SRP9180_UW_FCC\SRP9180UW Exhibits Word\FCC_SRP9180UW_authorisation.doc Andrew Cutler EMC Technologies (NZ) Ltd 47 MacKelvie Street Grey Lynn Auckland Ref: Re: STZSRP9170UW: FCC Equipment Approval 29 October 2012 To Whom It May Concern: Please be advised that ComGroup Australia Pty Ltd authorises EMC Technologies (NZ) Ltd to act on our behalf, until otherwise notified, for applications submitted to the Federal Communications Commission and/or Telecommunications Certification Body. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862. Further, no party to the application, as defined in 47 CFR 1.2002(b), is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Yours sincerely, Robert Stowell Senior Engineer ComGroup Australia Pty Ltd ABN 29 095 068 429 www.comgroup.net.au 1270 Ferntree Gully Rd, Scoresby Victoria 3179, Australia Tel: +61 3 9730 3800 Fax: +61 3 9730 3968 Email: [email protected]

Form Number: FN0024_0 Page 1 of 1 Filename: H:\Standards\FCC\SRP9180_FCC_IC\SRP9180_UW_FCC\SRP9180UW Exhibits Word\FCC_SRP9180UW_Confidentiality_Timco_090512.doc Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Timco Engineering Inc 849 N.W. State Road 45 PO Box 370 Newberry Florida 32669 Ref: Re: STZSRP9170UW: FCC Equipment Approval Confidentiality 29 October 2012 To Whom It May Concern: The following information is to be held confidential pursuant of 47 CFR Part 0 §0.459 and Section 552(b)(4) of the Freedom of Information Act, because the information provided contains trade secrets and is proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. • Schematics • Operational Description • Block Diagram • Parts List • Tune Up Instruction • User Manual [NOTE: This request is for the “Technical” manual that is used as a service manual by authorised personnel and contains detailed technical information including operational descriptions and Tune Up information]. Yours sincerely, Robert Stowell Senior Engineer ComGroup Australia Pty Ltd ABN 29 095 068 429 www.comgroup.net.au 1270 Ferntree Gully Rd, Scoresby Victoria 3179, Australia Tel: +61 3 9730 3800 Fax: +61 3 9730 3968 Email: [email protected]

Form Number: FN0024_0 Page 1 of 1 Filename: H:\Standards\FCC\SRP9180_FCC_IC\SRP9180_UW_FCC\SRP9180UW Exhibits Word\FCC_SRP9180 UW_Extended Frequency Justification_020712.doc Timco Engineering Inc 849 N.W. State Road 45 PO Box 370 Newberry Florida 32669 Ref: Re: STZSRP9170UW: Extended Frequency Justification 29 October 2012 Dear Sir/ Madam, ComGroup Australia would like to submit the following justification to show the frequency range as 440 – 512 MHz on the Grant of Equipment Authorization for STZSRP9170UW portable radiocommunications transceiver. This frequency range is applicable to FCC Part 90 radiocommunication systems that would include public agencies, emergency services, commercial, business and industrial services etc. These services account for the majority of users on this band. Also the frequency of operation of the STZSRP9170UW radio cannot be programmed by the operator to transmit on frequencies other than those programmed by service or maintenance personnel. From the FCC KDB634187 guide, it is noted that FCC rules would be violated if the STZSRP9170UW equipment were programmed and operated on unauthorized frequencies. Sincerely, Robert Stowell Senior Engineer ComGroup Australia Pty Ltd ABN 29 095 068 429 www.comgroup.net.au 1270 Ferntree Gully Rd, Scoresby Victoria 3179, Australia Tel: +61 3 9730 3800 Fax: +61 3 9730 3968 Email: [email protected]

Form Number: FN0024_0 Page 1 of 1 Filename: H:\Standards\FCC\SRP9180_FCC_IC\SRP9180_UW_FCC\SRP9180UW Exhibits Word\FCC_SRP9180UW_Frequency Programming_Timco.doc Timco Engineering Inc 849 N.W. State Road 45 PO Box 370 Newberry Florida 32669 Ref: Re: STZSRP9170UW: 47 CFR Part 90.203(e) Compliance 29 October 2012 To Whom It May Concern: The frequency of operation of the STZSRP9170UW portable radio cannot be programmed by the operator to transmit on frequencies other than those programmed by service or maintenance personnel. The STZSRP9170UW radio requires the operating frequencies to be programmed through the use of an external device only available to service or maintenance personnel. Yours sincerely, Robert Stowell Senior Engineer ComGroup Australia Pty Ltd ABN 29 095 068 429 www.comgroup.net.au 1270 Ferntree Gully Rd, Scoresby Victoria 3179, Australia Tel: +61 3 9730 3800 Fax: +61 3 9730 3968 Email: [email protected]

ComGroup Australia Pty Ltd ABN 29 095 068 429 www.comgroup.net.au 1270 Ferntree Gully Rd, Scoresby Victoria 3179, Australia Tel: +61 3 9730 3800 Fax: +61 3 9730 3968 Email: [email protected] NON DISCLOSURE AGREEMENT BETWEEN: ComGroup Australia Pty. Ltd. 1270 Ferntree Gully Road Scoresby Victoria 3179 Australia AND: (Purchaser/ Recipient Details) SUBJECT OF AGREEMENT: SRP9170/80 Series Service Manual Issue 1.01C, June 2012 Confidential Information CONFIDENTIALITY: This SRP9170/80 Series Service Manual contains information that, should it become public, might be used to disadvantage ComGroup Australia Pty. Ltd. in the market place. The information contained in the Service Manual is the confidential information of ComGroup Australia Pty. Ltd. and at all times remains their property. The recipient of this information shall not use, copy, abstract or disclose any information it receives or anything it learns as a result of the information to any other person, firm, corporation or other entity without the express consent of ComGroup Australia. Dissemination of the information by the recipient shall be limited to the recipient’s employees who have a need to know and who shall be bound to honor the provisions of this Agreement. EXCEPTIONS. The obligation of confidentiality shall not apply to any information which: (a) is contained in a generally available non-confidential publication bearing a date prior to the date of this agreement; (b) is or becomes generally available to the public other than as a result of the improper action of the recipient. USE OF INFORMATION. All information shall be used by the recipient solely for the purpose of support for ComGroup Australia Pty. Ltd. products and services. The parties acknowledge that they have read and understood this agreement and agree to be bound by its terms Date Date: Signed Signed: Name (Print) Name (Print) Company Name ComGroup Australia Pty. Ltd. Company Name Purchaser/ Recipient Position Position

Form Number: FN0024_0 Page 1 of 1 Filename: H:\Standards\FCC\SRP9180_FCC_IC\SRP9180_UW_FCC\SRP9180UW Exhibits Word\FCC_SRP9180UW_Spectrum_Efficiency_Timco.doc Timco Engineering Inc 849 N.W. State Road 45 PO Box 370 Newberry Florida 32669 Ref: Re: STZSRP9170UW: 47 CFR Part 90.203(j)(3) Compliance 29 October 2012 To Whom It May Concern: This is to certify that the requirements of 47 CFR Part 90.203(j)(3) spectrum efficiency standard of one voice channel per 12.5kHz of channel bandwidth are met by the STZSRP9170UW portable radio as demonstrated by the tests conducted on the sample radio provided (11k0F3E emission). Additionally in this sample, the C4FM data rate is in accordance with TIA-102, that is 9600 bits per second in a 12.5kHz channel bandwidth, therefore the STZSRP9170UW transmitted data satisfies the requirement of 4800 bits per second per 6.25kHz of channel bandwidth for 8K10F1E and 8K10F1D emissions. Yours sincerely, Robert Stowell Senior Engineer ComGroup Australia Pty Ltd ABN 29 095 068 429 www.comgroup.net.au 1270 Ferntree Gully Rd, Scoresby Victoria 3179, Australia Tel: +61 3 9730 3800 Fax: +61 3 9730 3968 Email: [email protected]

____________________________________________________________________________________________________________________________________________________________________________ Page 22 of 29 Test Report No 121017.1 29 th November 2012. This report may not be reproduced except in full. 10. PHOTOGRAPH (S) ____________________________________________________________________________________________________________________________________________________________________________ Page 23 of 29 Test Report No 121017.1 29 th November 2012. This report may not be reproduced except in full.

____________________________________________________________________________________________________________________________________________________________________________ Page 23 of 29 Test Report No 121017.1 29 th November 2012. This report may not be reproduced except in full.

____________________________________________________________________________________________________________________________________________________________________________ Page 26 of 29 Test Report No 121017.1 29 th November 2012. This report may not be reproduced except in full. Internal Photos ____________________________________________________________________________________________________________________________________________________________________________ Page 27 of 29 Test Report No 121017.1 29 th November 2012. This report may not be reproduced except in full. ____________________________________________________________________________________________________________________________________________________________________________ Page 28 of 29 Test Report No 121017.1 29 th November 2012. This report may not be reproduced except in full. ____________________________________________________________________________________________________________________________________________________________________________ Page 29 of 29 Test Report No 121017.1 29 th November 2012. This report may not be reproduced except in full.

Report No.: M121040F Page 19 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. APPENDIX A1 Test Sample Photographs Battery 1 Battery 2 DUT DUT Report No.: M121040F Page 20 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. APPENDIX A2 Test Setup Photographs Passive SPK-MIC Antenna SPK-MIC Holster Report No.: M121040F Page 21 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. APPENDIX A3 Test Setup Photographs Face Frontal Position Belt Clip Position Report No.: M121040F Page 22 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. APPENDIX A4 TEST SETUP PHOTOGRAPHS Belt Clip Position with Holster Report No.: M121040F Page 23 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. APPENDIX A5 Test Setup Photographs Face Frontal Position SPK_MIC Belt Clip Position SPK_MIC

Report No.: M121040F Page 24 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. APPENDIX B Plots Of The SAR Measurements Plots of the measured SAR distributions inside the phantom are given in this Appendix for all tested configurations. The spatial peak SAR values were assessed with the procedure described in this report. Table: SAR Measurement Plot Numbers 1. Test Position 2. Plot No. 4. Test Freq (MHz) Belt Clip 1 440.075 2 458.075 3 476.075 Belt Clip with Holster 4 440.075 5 458.075 6 476.075 Face Frontal 7 458.075 Belt Clip SPK-MIC 8 458.075 9 476.075 10 494.075 Face Frontal SPK-MIC 11 458.075 Table: Prescans SAR Scan Plot Numbers 1. Test Position 2. Plot No. 3. Test Ch Face Frontal 12 0 1 2 3 4 Face Frontal SPK-MIC 13 0 1 2 3 4 Body Worn Back Belt Clip 14 0 1 2 3 4 Body Worn Back Belt Clip SPK-MIK 15 0 1 2 3 4 Table: Validation Plot Numbers Date Plot Number Frequency 12 th November 2012 16 450 MHz 13 th November 2012 17 450 MHz Report No.: M121040F Page 25 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Test Date: 13 November 2012 File Name: M121040 450 MHz Belt Clip 13-11-12.da52:0 DUT: SIMOCO PTT RF SPK/MIC; Type: SRP9180 UW; Serial: FT9HX1228DDBK * Communication System: CW; Frequency: 440.075 MHz; Duty Cycle: 1:1 * Medium parameters used: f = 440 MHz; σ = 0.923 mho/m; ε r = 56.831; ρ = 1000 kg/m 3 - Electronics: DAE3 Sn442; Probe: ET3DV6 - SN1380; ConvF(7.41, 7.41, 7.41); Calibrated: 12/12/2011 - Phantom: ELI 4.0; Serial: 1101; Phantom section: Flat Section Configuration/Channel 0 Test/Area Scan (81x231x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 8.72 W/kg Configuration/Channel 0 Test/Zoom Scan (7x8x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 82.871 V/m; Power Drift = -0.17 dB Peak SAR (extrapolated) = 12.172 mW/g SAR(1 g) = 8.27 mW/g; SAR(10 g) = 6.01 mW/g Maximum value of SAR (measured) = 9.45 W/kg 0 dB = 8.72 W/kg = 18.81 dB W/kg SAR MEASUREMENT PLOT 1 Ambient Temperature 20.1 Degrees Celsius Liquid Temperature 19.8 Degrees Celsius Humidity 44.0% Report No.: M121040F Page 26 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 27 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Test Date: 13 November 2012 File Name: M121040 450 MHz Belt Clip 13-11-12.da52:0 DUT: SIMOCO PTT RF SPK/MIC; Type: SRP9180 UW; Serial: FT9HX1228DDBK * Communication System: CW; Frequency: 458.075 MHz; Duty Cycle: 1:1 * Medium parameters used: f = 458 MHz; σ = 0.937 mho/m; ε r = 56.324; ρ = 1000 kg/m 3 - Electronics: DAE3 Sn442; Probe: ET3DV6 - SN1380; ConvF(7.41, 7.41, 7.41); Calibrated: 12/12/2011 - Phantom: ELI 4.0; Serial: 1101; Phantom section: Flat Section Configuration/Channel 1 Test/Area Scan (81x231x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 9.60 W/kg Configuration/Channel 1 Test/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 84.696 V/m; Power Drift = -0.13 dB Peak SAR (extrapolated) = 13.604 mW/g SAR(1 g) = 9.09 mW/g; SAR(10 g) = 6.58 mW/g Maximum value of SAR (measured) = 9.53 W/kg 0 dB = 9.60 W/kg = 19.65 dB W/kg SAR MEASUREMENT PLOT 2 Ambient Temperature 20.1 Degrees Celsius Liquid Temperature 19.8 Degrees Celsius Humidity 44.0% Report No.: M121040F Page 28 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 29 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Test Date: 13 November 2012 File Name: M121040 450 MHz Belt Clip 13-11-12.da52:0 DUT: SIMOCO PTT RF SPK/MIC; Type: SRP9180 UW; Serial: FT9HX1228DDBK * Communication System: CW; Frequency: 476.075 MHz; Duty Cycle: 1:1 * Medium parameters used: f = 476 MHz; σ = 0.958 mho/m; ε r = 56.084; ρ = 1000 kg/m 3 - Electronics: DAE3 Sn442; Probe: ET3DV6 - SN1380; ConvF(7.41, 7.41, 7.41); Calibrated: 12/12/2011 - Phantom: ELI 4.0; Serial: 1101; Phantom section: Flat Section Configuration/Channel 2 Test/Area Scan (81x231x1): Inter…

Text truncated - open the document above for the full version.

Report No.: M121040F Page 55 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. APPENDIX C CALIBRATION DOCUMENTS 1. SN: 1380 Probe Calibration Certificate 2. SN: 1074 D450V3 Dipole Calibration Certificate 3. SN: 442 DAE3 Data Acquisition Electronics Calibration Certificate Report No.: M121040F Page 56 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 57 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 58 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 59 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 60 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 61 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 62 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 63 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 64 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 65 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full. Report No.: M121040F Page 66 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document shall not be reproduced except in full.

Report No.: M121040F Page 67 of 78 Accredited for compliance with ISO/IEC 17025. The results of the test, calibrations and/or measurement included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recogni…

Text truncated - open the document above for the full version.