T58DL4312R150Mbps Wireless N ADSL2+ Modem Router

netis Wireless N ADSL2+ Modem Router Quick Installation Guide R CONTENTS 1 English 6 Español 11 Português 16 Français 1.Package Contents * This QIG is for all netis 150Mbps/300Mbps wireless N ADSL2+ modem routers, including models- DL4310, DL4310D, DL4311, DL4311D, DL4312, DL4312D, DL4322, DL4322D, DL4323, DL4323D , etc. * The product model shown in this QIG is DL4323, as an example. netis Wireless N ADSL2+ Modem Router Quick Installation Guide 1 2.Hardware Connection Wireless N ADSL2+ Modem Router Power Adapter ADSL Splitter Ethernet CableTelephone Cable *2 QIG MODEM netis Wireless N ADSL2+ Modem Router Quick Installation Guide 2.1. Connect the ADSL line with the attached telephone cable. Connect the LINE port of ADSL Splitter to the wall jack with a telephone cable. Connect the MODEM port of ADSL Splitter to the ADSL port on netis Modem Router with the other telephone cable. Connect your telephone to the PHONE port of ADSL Splitter. Tip: If no telephone is needed, please connect the ADSL port on netis Modem Router to the wall jack with the phone cable directly. 2.2. Connect your computer to one of the LAN ports on netis Modem Router with an Ethernet cable. 2.3. Plug the provided Power Adapter into the PWR jack of netis Modem Router and the other end to a standard electrical socket. 2.4. Wait for one minute then check if the LED indicators of the Modem Router display normally. PWR: Solid on. ADSL: Solid on when the modem is synchronized. LAN: Solid on or flashing if the corresponding LAN port is connected. Tip: If the LED indicators display abnormally, please check if all the cables are well connected. If the ADSL LED is off or flashing, please contact your ISP (Internet Service Provider) to check the Internet connection. PHONE 2 3. Configure the Modem Router via Web Management Page 3.1. Necessary Information before the configuration. For a successful setup, you're recommended to contact your ISP first and ask for the following network parameters which will be required during the configuration procedures. a. VPI/VCI; b. Connection Type; c. Encapsulation Type (Optional); d. Username & Password (Optional, according to your Connection Type). 3.2. Set the IP address of the wired network adapter on your computer as “Automatic” or “DHCP”. For Windows 8/ 7/Vista 1) Go to “Settings” (Win 8)/“Start” (Win 7/Vista)> “Control Panel”. 2) Left-click on “Network and Internet”> “Network and Sharing Center”> “Change adapter settings” (Win 8/7)/“Manage network connections” (Win Vista). 3) Right-click on “Local Area Connection” and left-click on “Properties”. 4) Double-click on “Internet Protocol Version 4 (TCP/IPv4)”. 5) Select “Obtain an IP address automatically” and “Obtain DNS server address automatically” then left-click on “OK”. For Windows XP/2000 1) Go to “Start”> “Control Panel”. 2) Left-click on “Network and Internet Connections”> “Network Connections”. 3) Right-click on “Local Area Connection” and left-click on “Properties”. 4) Double-click on “Internet Protocol (TCP/IP)”. 5) Select “Obtain an IP address automatically” and “Obtain DNS server address automatically” then left-click on “OK”. For MAC OS 1) Click on the “Apple” menu> “System Preferences”. 2) Click on the “Network” icon. 3) Click on “Ethernet” in the left side box and click on “Advanced” in the lower right corner. 4) In the top options, select “TCP/IP”. 5) In the pull-down menu next to “Configure IPv4” select “Using DHCP”. 6) Click “OK” then “Apply”. 192.168.1.1 3.3. Open your browser and type 192.168.1.1 in the address field. Then type in the username guest and password guest to login the web management page. netis Wireless N ADSL2+ Modem Router Quick Installation Guide 3 3.4. Under “Quick Start” page, left-click on “START” and the Wizard will guide you through the following four steps. Then left-click on “NEXT”. 1) Set the PVC (VPI/VCI) value. Left-click “Cancel” if you know the PVC (VPI/VCI) from your ISP, then input the value manually. If you don't know the exact value, please left-click on “OK”, and then it will take less than one minute to search for the available PVC automatically. Once the PVC value is input or shows up in the following page, left-click on “NEXT”. netis Wireless N ADSL2+ Modem Router Quick Installation Guide 3) Configure your wireless network name (SSID) and password, and then left-click on “NEXT”. 4) Left-click on “NEXT” and then “CLOSE” to save the current settings. Quick Start will be finished. 2) Select the Internet Connection Type given by your ISP, then left-click on “NEXT”. If “Dynamic IP Address” is selected, select the Connection Type defined by your ISP and the router will automatically receive the IP parameters from your ISP. If “Static IP Address” is selected, enter the IP Address/Subnet Mask/ISP Gateway/DNS Servers/Connection Type given by your ISP. If “PPPoE/PPPoA” is selected, input the Username/ Password and select the Connection Type given by your ISP. If “Bridge Mode” is selected, select the Connection Type defined by your ISP. Tip 1: Default IP address: 192.168.1.1 Default login username: guest Default SSID: netis Default login password: guest Default wireless password: password 4 netis Wireless N ADSL2+ Modem Router Quick Installation Guide Tip 2: After the basic Internet settings, you may open some popular websites to check your Internet connection. If you cannot access the Internet, please refer to the instructions in “Troubleshooting”. How do I restore my netis Modem Router's configuration to its default settings? With the router powered on, use a pin to press and hold the Default button on the rear panel for 8 to 10 seconds before releasing it. The router will reboot and all configurations are back to factory default. Q A 4.Troubleshooting What can I do if my Internet cannot be accessed? 1) Check to verify the hardware connections are correct. Please refer to the “Hardware Connection” step. 2) Login to netis Modem Router's web management page and ensure that you input the correct netwo…

Text truncated - open the document above for the full version.

NETIS SYSTEMS CO., LTD 4F & 5F, R&D Building, Oriental Cyberport, High-Tech Industrial Park, Nanshan, Shenzhen, China Date (May ,05 ,2014) BABT FCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Dear Sir or Madam, Due to the business consideration, we hereby declare that our product of 150 Mbps Wireless N ADSL2+ Modem Router Model: DL4312; DL4312D have as following difference Serial model DL4312 with fixed antenna; DL4312D with detachable antenna Any questions regarding this declaration, please don’t hesitate to contact us. Sincerely, Signature___________________________________ Name/Title: SelenaBai / Director Contact information / Address 4F & 5F, R&D Building, Oriental Cyberport, High-Tech Industrial Park, Nanshan, Shenzhen, China TEL: +86 0755-86186790 FAX: +86 0755-86186779 Email: [email protected]

NETIS SYSTEMS CO., LTD 4F & 5F, R&D Building, Oriental Cyberport, High-Tech Industrial Park, Nanshan, Shenzhen, China Date : May , 12 ,2014 BABT TCB Forsyth House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Confidentiality Request FCC ID: T58DL4312R Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, NETIS SYSTEMS CO., LTD hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation NETIS SYSTEMS CO., LTD also hereby requests short-term confidential treatment of information accompanying this application as outlined below for a period of: 15/11/2014 Internal Photos External Photos User Manual Test Set-up Photographs The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, _____________________________________ Signature Company Officer: SelenaBai / Director Telephone Number: +86 0755-86186790 Email: [email protected]

Letter of Authorization We Name: NETIS SYSTEMS CO., LTD. Address: 4F&5F R&D Building,Oriental Cyberport High-Tech Industrial Park, Nanshan, Shenzhen, China Declare the following Person: Name： Alex Chen Title：Vice President is authorized to sign all the related doucuments of FCC certification，the signature has the same effectas as SelenaBai: on our behalf. Authorized Person: SelenaBai Signature: City: Shenzhen Date: 2014-2-26

Report No: T140328D06 Page 1 / 13 Rev.00 EXTERNAL PHOTOGRAPHS OF EUT DL4312 Report No: T140328D06 Page 2 Rev.00 Report No: T140328D06 Page 3 Rev.00 DL4312D Report No: T140328D06 Page 4 Rev.00 Report No: T140328D06 Page 5 Rev.00 Report No: T140328D06 Page 6 Rev.00 Antenna Report No: T140328D06 Page 7 Rev.00 Tenpao / NT120050UL

Report No: T140328D06 Page 8 Rev.00 INTERNAL PHOTOGRAPHS OF EUT DL4312 Report No: T140328D06 Page 9 Rev.00 Report No: T140328D06 Page 10 Rev.00 DL4312D Report No: T140328D06 Page 11 Rev.00 Report No: T140328D06 Page 12 Rev.00 Report No: T140328D06 Page 13 Rev.00

Compliance Certification Services Inc. Report No.: T140328D06-MF Date of Issue: April 28, 2014 Page 1 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. APPENDIX I RADIO FREQUENCY EXPOSURE LIMIT According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter. EUT Specification EUT 150Mbps Wireless N ADSL2+ Modem Router Model DL4312; DL4312D RF Module Realtek Model: RTL8188ER-CG Model Discrepancy All the model numbers (list on this report) are identical, just for marketing purpose only except Antenna. Model Number Antenna DL4312 Fixed DL4312D Detachable Frequency band (Operating) 802.11b/g/n HT20: 2.412GHz ~ 2.462GHz 802.11n HT40: 2.422GHz ~ 2.452GHz Others Device category Portable (<20cm separation) Mobile (>20cm separation) Others Exposure classification Occupational/Controlled exposure (S = 5mW/cm2) General Population/Uncontrolled exposure (S=1mW/cm2) Antenna Specification 2.4GHz: Antenna Gain : 5.00 dBi (Numeric gain: 3.16) Maximum Average output power IEEE 802.11b Mode: 12.43 dBm(17.498 mW) IEEE 802.11g Mode: 13.86 dBm(24.322 mW) IEEE 802.11n HT 20 Mode: 13.67 dBm(23.281 mW) IEEE 802.11n HT 40 Mode: 13.66 dBm(23.227 mW) Maximum Tune up Power IEEE 802.11b Mode: 13.00 dBm (19.953 mW) IEEE 802.11g Mode: 15.00 dBm (31.623 mW) IEEE 802.11n HT 20 Mode: 14.00 dBm (25.119 mW) IEEE 802.11n HT 40 Mode: 15.00 dBm (31.623 mW) Evaluation applied MPE Evaluation* SAR Evaluation N/A Compliance Certification Services Inc. Report No.: T140328D06-MF Date of Issue: April 28, 2014 Page 2 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Revision History Rev. Issue Date Revisions Effect Page Revised By 00 2014/04/28 Initial Issue ALL Scott Hsu Compliance Certification Services Inc. Report No.: T140328D06-MF Date of Issue: April 28, 2014 Page 3 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. TEST RESULTS No non-compliance noted. Calculation Given d G P E    30 & 377 2 E S  Where E = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / square centimeter Combining equations and re-arranging the terms to express the distance as a function of the remaining variables yields: 2 377 30 d G P S    Changing to units of mW and cm, using: P (mW) = P (W) / 1000 and d (cm) = d(m) / 100 Yields     2 2 0796 . 0 100 / 377 1000 / 30 d G P d G P S        Equation 1 Where d = Distance in cm P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 Compliance Certification Services Inc. Report No.: T140328D06-MF Date of Issue: April 28, 2014 Page 4 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Maximum Permissible Exposure Substituting the MPE safe distance using d = 20 cm into Equation 1: G P S    000199 . 0 Where P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 IEEE 802.11b mode: Ch. Frq.(MHz) P (mW) Gain (num.) D (cm) Power density in mW / cm 2 Limit (mW/cm2) 11 2462 19.953 3.16 20 0.0125 1 IEEE 802.11g mode: Ch. Frq.(MHz) P (mW) Gain (num.) D (cm) Power density in mW / cm 2 Limit (mW/cm2) 6 2437 31.623 3.16 20 0.0199 1 IEEE 802.11n HT20 mode: Ch. Frq.(MHz) P (mW) Gain (num.) D (cm) Power density in mW / cm 2 Limit (mW/cm2) 6 2437 25.119 3.16 20 0.0158 1 IEEE 802.11n HT40 mode: Ch. Frq.(MHz) P (mW) Gain (num.) D (cm) Power density in mW / cm 2 Limit (mW/cm2) 6 2437 31.623 3.16 20 0.0199 1

Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 1 / 87 Rev.00 FCC 47 CFR PART 15 SUBPART C TEST REPORT For 150Mbps Wireless N ADSL2+ Modem Router Model: DL4312; DL4312D Trade Name: netis Issued to NETIS SYSTEMS CO., LTD 4F & 5F, R&D Building, Oriental Cyberport, High-Tech Industrial Park, Nanshan, Shenzhen, China Issued by Compliance Certification Services Inc. No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841, Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 http://www.ccsrf.com [email protected] Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 2 Rev.00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 April 23, 2014 Initial Issue All Iren Wang Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 3 Rev.00 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION......................................................................................... 4 2 EUT DESCRIPTION............................................................................................................. 5 3 TEST METHODOLOGY....................................................................................................... 6 3.1 EUT CONFIGURATION ..................................................................................................... 6 3.2 EUT EXERCISE ................................................................................................................. 6 3.3 GENERAL TEST PROCEDURES ...................................................................................... 6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .......................................... 7 3.5 DESCRIPTION OF TEST MODES..................................................................................... 8 4 INSTRUMENT CALIBRATION ............................................................................................ 9 4.1 MEASURING INSTRUMENT CALIBRATION..................................................................... 9 4.2 MEASUREMENT EQUIPMENT USED .............................................................................. 9 4.3 MEASUREMENT UNCERTAINTY ................................................................................... 10 5 FACILITIES AND ACCREDITATIONS ................................................................................11 5.1 FACILITIES........................................................................................................................11 5.2 LABORATORY ACCREDITATIONS AND LISTING ...........................................................11 5.3 TABLE OF ACCREDITATIONS AND LISTINGS............................................................... 12 6 SETUP OF EQUIPMENT UNDER TEST ........................................................................... 13 6.1 SETUP CONFIGURATION OF EUT................................................................................. 13 6.2 SUPPORT EQUIPMENT .................................................................................................. 13 7 FCC PART 15 REQUIREMENTS....................................................................................... 14 7.1 6DB BANDWIDTH............................................................................................................ 14 7.2 PEAK POWER .................................................................................................................22 7.3 AVERAGE POWER .......................................................................................................... 24 7.4 BAND EDGES MEASUREMENT ..................................................................................... 26 7.5 PEAK POWER SPECTRAL DENSITY ............................................................................. 48 7.6 SPURIOUS EMISSIONS.................................................................................................. 56 7.7 POWERLINE CONDUCTED EMISSIONS ....................................................................... 80 8 APPENDIX I PHOTOGRAPHS OF TEST SETUP ............................................................. 83 9 APPENDIX II: PHOTOGRAPHS OF EUT.......................................................................... 87 Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 4 Rev.00 1 TEST RESULT CERTIFICATION Applicant: NETIS SYSTEMS CO., LTD 4F & 5F, R&D Building, Oriental Cyberport, High-Tech Industrial Park, Nanshan, Shenzhen, China Manufacturer: Shenzhen Netcore Industrial Ltd. 4F & 5F, R&D Building, Oriental Cyberport, High-Tech Industrial Park, Nanshan, Shenzhen, China Equipment Under Test: 150Mbps Wireless N ADSL2+ Modem Router Trade Name: netis Model: DL4312; DL4312D Date of Test: April 1 ~ 2, 2014 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: Compliance Certification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Stan Lin Section Manager Angel Hu Section Manager Compliance Certifica…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 83 Rev.00 8 APPENDIX I PHOTOGRAPHS OF TEST SETUP Radiated Emissions Setup Photos Below 1GHz Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 84 Rev.00 Above 1GHz Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 85 Rev.00 Conducted Emissions Setup Photo Compliance Certification Services Inc. Report No.: T140328D06-RP1 FCC ID: T58DL4312R Date of Issue: April 23, 2014 Page 86 Rev.00 Powerline Conducted Emissions Setup Photos