T7V1780Bluetooth LE LR Module

Wireless Connectivity PAN1780 Bluetooth ® Low Energy Module Module Integration Guide Rev. 1.1  PAN1780 Bluetooth Module Module Integration Guide Rev. 1.1 Page 2 of 48 Overview The PAN1780 is a Bluetooth 5 Low Energy (LE) module based on the Nordic nRF52840 single chip controller. Features • Surface mount type dimensions: 15.6 mm x 8.7 mm x 2 mm • Same form factor as PAN1026A and PAN1762 but smaller pitch and more pins • Nordic nRF52840 featuring ARM ® Cortex ® -M4F with 64 MHz • Bluetooth 5 LE including LE 2M and LE Coded PHY • Embedded 1 MB flash memory and 256 kB internal RAM • Includes ARM TrustZone ® CryptoCell ® 310 and supports secure boot including Root of Trust (RoT) • Up to 48 general purpose I/Os (GPIO), which are shared by up to 4 SPI, 2 I²C, 2 UART, 4 PWM, 8 ADC, 1 NFC-A, 32 kHz IN/OUT, nRESET • USB 2.0 full-speed device interface • Built in temperature sensor Bluetooth • LE 2 Mbps high speed PHY, LE long range coded PHY • LE advertising extensions (advertising on 40 channels total) • Channel selection algorithm #2 • LE secure connections • Over-the-air update of application software • Qualified Bluetooth mesh profile stack Characteristics • Typical sensitivity: -95 dBm at 1 Mb/s and -103 dBm at 125 kb/s • Typical max. output power: 8 dBm, configurable from -20 dBm in 4 dB steps and -40 dBm in whisper mode • Typical current consumption: 4.8 mA in Tx (at 0 dBm) and 4.8 mA in Rx mode • Typical current consumption: 0.4 μA in System OFF mode, 1.5 μA with RTC wake up • On-module DC/DC and LDO regulators with automated low current modes • Voltage range: 1.7 V to 5.5 V • Temperature range: -40 °C to 85 °C Block Diagram  PAN1780 Bluetooth Module Module Integration Guide Rev. 1.1 Page 3 of 48 By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Module Integration Guide before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2020. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Module Integration Guide does not lodge the claim to be complete and free of mistakes. Engineering Samples (ES) If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. Disclaimer The customer acknowledges that samples may deviate from the Module Integration Guide and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by:  The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer,  Deviation or lapse in function of the Engineering Sample,  Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager. The information contained herein is presented only as guidance for Product use. No responsibility is assumed by Panasonic for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. Description of hardware, software, and other information in this document is only intended to illustrate the functionality of the referred Panasonic product. It should not be construed as guaranteeing specific functionality of the product as described or suitable for a particular application. Any provided (source) code shall not be used or incorporated into any products or systems whose manufacture, use or sale is prohibited under any applicable laws or regulations. Any outlined or referenced (source) code within this document is provided on an “as is” basis without any right to technical support or updates and without warranty of any kind on a free of charge basis according to § 516 German Civil Law (BGB) including without limitation, any warranties or conditions of title, non infringement, merchantability, or fitness for a particular purpose. Customer acknowledges that (source) code may bear defects and errors.  PAN1780 Bluetooth Module Module Integration Guide Rev. 1.1 Page 4 of 48 The third-party tools mentioned in this document are offered by independent third-party providers who are solely responsible for these products. Panasonic has no responsibility whatsoever for the performance, product descriptions, specifications, referenced content, or any and all claims or representations of these third-party providers. Panasonic makes no warranty whatsoever, neither express nor implied, with respect to the goods, the referenced contents, or any and all claims or representations of the third-party providers. To the maximum extent allowable by Law Panasonic assumes no liability whatsoever including without limitation, indirect, consequential, special, or incidental damages or loss, including without limitation loss of profits, loss of oppo…

Text truncated - open the document above for the full version.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 2020-04-01 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Number Product Title/Model T7V1780 PAN1780 For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram, Schematics, Parts Lists or Tune Up Information. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, (signed) Name: Olaf Knoth Company: Panasonic Industrial Devices Europe GmbH Address: Zeppelinstraße 19, 21337 Lüneburg Phone: +49 4131 899 257 Email: [email protected]

SHORT-TERM CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 2020-04-01 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests short term confidentiality for the following product: FCC ID Number Product Title/Model T7V1780 PAN1780 For the product stated above, we request that the following information be held confidential: 1. External and Internal Photographs 2. Test Setup Photos 3. User Manual We request this confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device, which is planned for 2020-09-30. If you have any questions, please feel free to contact me at the address shown below. Sincerely, (signed) Name: Olaf Knoth Company: Panasonic Industrial Devices Europe GmbH Address: Zeppelinstraße 19, 21337 Lüneburg Phone: +49 4131 899 257 Email: [email protected]

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Industry Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Subject: FCC / ISED Modular Approval Statement FCC ID: Only applicable for ISED certification: IC Company Number: UPN: HVIN: (Hardware Version Identification Number) PMN: (Product Marketing Name) HMN: (Host Marketing Name) FVIN: (Firmware Version Identification Number) TO WHOM IT MAY CONCERN Pursuant to Paragraphs RSP-100 Issue 10 November 2014 Item 7.3 and CFR § 15.212, we herewith declare for our module. Modular approval requirement Yes No * (a) The radio elements must have the radio frequency circuitry be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. *Please provide a detailed explanation if the answer is “No.”: (b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS standard under conditions of excessive data rates or over-modulation. *Please provide a detailed explanation if the answer is “No.”: (c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. *Please provide a detailed explanation if the answer is “No.”: (d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. *Please provide a detailed explanation if the answer is “No.”: Yes No * (e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing. *Please provide a detailed explanation if the answer is “No.”: (f) The module shall comply with the Category I equipment labeling requirements and CFR § 15.212(a)(1)(vi). *Please provide a detailed explanation if the answer is “No.”: (g) The module shall comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement which are based on the intended use/configurations. *Please provide a detailed explanation if the answer is “No.”: Only applicable for ISED certification: (h) Is the modular device for an Industry Canada licensed exempt service? (i) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. If you have any questions, please feel free to contact us at the address shown below Be st Regards, Company Name: Ph one: Company Address: Fa x: Email: Contact Name: Signature: Si gnature Date: INF O for applicant: LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product, into which the module will be installed, will be maintained, such that full compliance of the end product is always ensured. 2019-03-25

REASONING PANASONIC BT MODUL PAN1780 WITHOUT IC ID ON PRODUCT CAUSED BY SIZE RESTRICTIONS In KDB784748D01V09r01 chapter 3 the FCC states the following: (3) CERTIFICATION For certification, the product shall bear a nameplate or label with the FCC Identifier (FCC ID), as defined in Section 2.925.13 The FCC ID must always be accessible when using the product. The placement of the FCC ID must be a physical label on the product, unless an e-label is used. Physical FCC ID labels must be located on the surface of the product, or within a user-accessible non-detachable compartment (such as the battery compartment). The label shall be permanently affixed, permitting the device to be positively identified. The font needs to be readily legible, consistent with the dimensions of the equipment and its label area. When the device is so small, or for such use that it is impracticable to label with a font size that is four-points or larger (and the device does not utilize electronic labeling), then the FCC ID shall be placed in the user manual, and the FCC ID shall also be placed either on the device packaging or on a removable label attached to the device Definition of point (pt) A computer point (pt) is the smallest unit of measure in typography. It is a subdivision of the larger pica. The contemporary desktop publishing point (also called the PostScript point) was defined as 72 points to the inch (1 point = 1⁄72 inches = 25.4⁄72 mm = 0.3527 mm). Conversion 4pt to mm 4pt = 0.3527 x 4mm = 1,4108mm The below dimensioned and magnified graphic shows the product with the actual label and a visualized IC ID printed in 4pt font size. It demonstrates that the IC ID doesn’t fit on the label if printed in 4pt. The brand name, product number, lot code and 2D data matrix code are laser printed in a font smaller than 2pt and are intended to be read by machines (scanner) or in a factory using a microscope. This product is intended to be sold to OEM’s only. The OEM is obliged to print on the label of the end product containing this BT module the following This product contains transmitter IC: 216Q-1780 Module Laser Marking Description No. Item ENW89854A1KF 1 Series (Brand) PAN1780 2 HW/SW Version HW Major Hardware Version: please refer to MS-CS-PAN1780 document SW Major Software Version: please refer to AI document 3 ENW-No. / Model Name ENW89854A1KF 4 Lotcode (YYWWDLL) YY - Year WW - Calendar Week D - Day of Week (e.g. Friday is 5) L - Line L - Lot 5 ES Marking Need to be mentioned during ES status (remove ES for MP) Necessity of ES marking will also be stated in the ECN 6 2D Data Matrix Code Contains in total 30 characters, seperated by a semicolon. YYWWDLL;HHHHHHHH;89853A1;HW(Minor Version);SW YYWWDLL Production Date Code (see No. 6 above) HHHHHHHH Last eight digits from hexadecimal Panasonic Mac Address (example: 001343ABCDEF) 89854A1 Part of the ENW-Number HW(Minor);SW(Minor) Minor Hardware and Minor Software Version, each 2 digits, please refer to MS-CS-PAN1780 and AI Document 7 Pin 1 Mark on Top Side Fix, no change at all 8 BT marking Bluetooth logo

BNetzA - CAB - 02/21 - 102 D - P L - 1 2 0 7 6 - 0 1 - 0 3 SAR Test exclusion documentation according to FCC KDB 447498, RSS-102 Report identification number: 1-9206/19-01-09-A Exclusion (FCC_ISED) contains the module with the following certification numbers FCC ID T7V1780 ISED number 216Q-1780 HVIN (Hardware Version Identification Number) ENW89854A1KF PMN (Product Marketing Name) PAN1780 FVIN (Firmware Version Identification Number) SD S140, SD S113 HMN (Host Marketing Name) -/- This report is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorised: Mihail Dorongovskij Marco Scigliano Lab Manager Testing Manager Radio Communications Radio Communications Test report no.: 1-9206/19-01-09-A © CTC advanced GmbH Page 2 of 2 EUT technologies: Technologies: Max. rated power: (AVG) Max. gain: Min. pathloss: Bluetooth LE Declared: max 8.5 dBm 0.4 dBi 0 dB (if applicable) Note: Bluetooth LE test results see CTC advanced test report 1-9206/19-01-06-A Max. Peak conducted measured: 8.5 dBm; Duty Cycle: 93.6% SAR test exclusion according to KDB447498 (General RF Exposure Guidance v06) Equation from Chapter 4.3.1: Standalone SAR test exclusion considerations page 11 and ff. (1) Standalone SAR test exclusion for 100 MHz to 6 GHz at test separation distances ≤ 50mm ( Threshold 1-g;10-g ) × d seperation / f 0.5 where Threshold 1-g;10-g is 3 for 1-g; 7.5 for 10-g d seperation is the min. test separation distance; 5mm is used if the distance is less f is the RF channel transmit frequency The table below gives the calculated maximal power that could be used for source based time averaged conducted or radiated power, adjusted for tune up tolerance. If this is at or below the calculated value the DUT is exempted from SAR evaluation. frequency d separation Powerlimit [MHz] [mm] [mW] [dBm] [mW] 2450.00 5 3 9.58 8.50 7.08 yes Threshold 1-g Exclusion P max-declared SAR test exclusion according to RSS-102 Issue 5 Section 2.5.1/Table 1 The table below gives the calculated maximal power that could be used for source based time averaged conducted or radiated power, adjusted for tune up tolerance. If this is at or below the calculated value the DUT is exempted from SAR evaluation. frequency d separation Powerlimit [MHz] [mm] [mW] [dBm] [mW] 2450.00 15 1 g 15.00 8.90 7.76 yes tissue volume P max-declared Exclusion The limits above are defined for body worn application and therefore cover all use cases.

BNetzA - CAB - 02/21 - 102 TEST REPORT Test report no.: 1-9206/19-01-06-A Testing laboratory Applicant CTC advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.ctcadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate starting with the registration number: D-PL-12076-01. Panasonic Industrial Devices Europe GmbH Zeppelinstrasse 19 21337 Lüneburg / GERMANY Phone: +49-4131-899-0 Contact: Marcus Nottorf e-mail: [email protected] Phone: +49 41 31 89 94 35 Manufacturer Panasonic Industrial Devices Europe GmbH Zeppelinstrasse 19 21337 Lüneburg / GERMANY Test standard/s FCC - Title 47 CFR Part 15 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 247 Issue 2 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence - Exempt Local Area Network (LE-LAN) Devices For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: Bluetooth Low Energy Module Model name: PAN1780 FCC ID: T7V1780 IC: 216Q-1780 Frequency: DTS band 2400 MHz to 2483.5 MHz Technology tested: Bluetooth ® LE Antenna: Integrated antenna Power supply: 3.3 V DC by external power supply Temperature range: -40°C to +85°C This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: Marco Bertolino Mihail Dorongovskij Lab Manager Lab Manager Radio Communications Radio Communications Test report no.: 1-9206/19-01-06-A © CTC advanced GmbH Page 2 of 58 1 Table of contents 1 Table of contents ............................................................................................................................................. 2 2 General information ......................................................................................................................................... 4 2.1 Notes and disclaimer ............................................................................................................................ 4 2.2 Application details ................................................................................................................................ 4 2.3 Test laboratories sub-contracted ......................................................................................................... 4 3 Test standard/s, references and accreditations .............................................................................................. 5 4 Test environment ............................................................................................................................................. 6 5 Test item .......................................................................................................................................................... 6 5.1 General description ............................................................................................................................... 6 5.2 Additional information .......................................................................................................................... 6 6 Sequence of testing ......................................................................................................................................... 7 6.1 Sequence of testing radiated spurious 9 kHz to 30 MHz ..................................................................... 7 6.2 Sequence of testing radiated spurious 30 MHz to 1 GHz .................................................................... 8 6.3 Sequence of testing radiated spurious 1 GHz to 18 GHz ..................................................................... 9 6.4 Sequence of testing radiated spurious above 18 GHz ....................................................................... 10 7 Description of the test setup.......................................................................................................................... 11 7.1 Shielded semi anechoic chamber ....................................................................................................... 12 7.2 Shielded fully anechoic chamber ........................................................................................................ 13 7.3 Radiated measurements > 18 GHz ...................................................................................................... 14 7.4 Conducted measurements Bluetooth system .................................................................................... 15 7.5 AC conducted ...................................................................................................................................... 16 8 Measurement uncertainty .............................................................................................................................. 17 9 Summary of measurement results ................................................................................................................ 18 10 Additional comments .............................................................................................................................. 19 11 Measurement results .............................................................................................................................. 20 11.1 System gain ..................................................................................................................................... 20 11.2 Power spectral density .................................................................................…

Text truncated - open the document above for the full version.

Measurement Results 1-9206/19-01-06_Annex_MR_A_1 Test logging This addendum is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Document authorized: Mihail Dorongovskij Lab Manager Radio Communications & EMC CTC advanced GmbHUntertuerkheimer Strasse 6-10 66117 Saarbruecken / Germany Phone: +49 681 5 98 - 0 Fax: +49 681 5 98 - 9075 web: ctcadvanced.com e-mail: [email protected] Table of Content IUT Summary3 1. FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE 1 Msps4 2. FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE 2 Msps11 3. FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE coded S818 4. FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE coded S225 5. FCC Part 15.247 Bandwidth 6dB DTS ~ BT LE 1 Msps32 6. FCC Part 15.247 Bandwidth 6dB DTS ~ BT LE 2 Msps36 7. FCC Part 15.247 Bandwidth 6dB DTS ~ BT LE coded S840 8. FCC Part 15.247 Bandwidth 6dB DTS ~ BT LE coded S244 9. FCC Part 15.247 Peak Power Spectral Density DTS ~ BT LE 1 Msps48 10. FCC Part 15.247 Peak Power Spectral Density DTS ~ BT LE 2 Msps52 11. FCC Part 15.247 Peak Power Spectral Density DTS ~ BT LE coded S856 12. FCC Part 15.247 Peak Power Spectral Density DTS ~ BT LE coded S260 13. FCC Part 15.247 Bandwidth 99PCT-20dB ~ BT LE 1 Msps64 14. FCC Part 15.247 Bandwidth 99PCT-20dB ~ BT LE 2 Msps71 15. FCC Part 15.247 Bandwidth 99PCT-20dB ~ BT LE coded S878 16. FCC Part 15.247 Bandwidth 99PCT-20dB ~ BT LE coded S285 17. FCC Part 15.247 TX Spurious Conduced ~ BT LE 1 Msps92 18. FCC Part 15.247 TX Spurious Conduced ~ BT LE 2 Msps96 19. FCC Part 15.247 TX Spurious Conduced ~ BT LE coded S8100 20. FCC Part 15.247 TX Spurious Conduced ~ BT LE coded S2104 21. FCC Part 15.247 Restricted Band Edge Conducted Peak DTS Video Avg ~ BT LE 1 Msps108 22. FCC Part 15.247 Restricted Band Edge Conducted Peak DTS Video Avg ~ BT LE 2 Msps111 23. FCC Part 15.247 Restricted Band Edge Conducted Peak DTS Video Avg ~ BT LE coded S8114 24. FCC Part 15.247 Restricted Band Edge Conducted Peak DTS Video Avg ~ BT LE coded S2117 25. Common2G4 Peak OP 3MHz/3MHz ~ BT LE 1 Msps120 Document No. 1-9206/19-01-06_Annex_MR_A_12/123 IUT Summary IUT DEFINITION & Common settings ManufacturerPanasonic Industrial Devices Europe GmbH TypePAN1780 Serial No. | Setup No.1 | 1.0 SW Version | HW VersionV01.03 | Nordic SD S140_nRF52 Comment 1 | 2 | Tlow | Tmid | Thigh [°C] -40 | 20 | 85 Vlow | Vmid | Vhigh [V] @Imax [A] 1.7 | 3.3 | 5.5 @1 Auto Control enabled Power Supply | Climatic BoxNo | No Antenna Gain [dBi]0 Additional Path Loss [dB]0 IUT Common Settings BT Low Energy Intermodulation Value N3 Image Freq. Low | Mid | High [MHz]0 | 0 | 0 Power Class2 1 Mbps supportedTrue | TXpayload 255 | RXpayload 255 2 Mbps supportedTrue | TXpayload 255 | RXpayload 255 Longrange S8 supportedTrue | TXpayload 255 | RXpayload 255 Longrange S2 supportedTrue | TXpayload 255 | RXpayload 255 Signaling Settings USB_RS232 | TWO | 41 | 19200 | None | S1 | None | On Signaling RF Settings RF1com | 0 | 0 | On | User InteractionNo Switch Matrix & Pathcompensation enabledYes Document No. 1-9206/19-01-06_Annex_MR_A_13/123 1. FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE 1 Msps Test References TC Start16.03.2020 13:45:40 System Version1.0.0.40 Test SpecificationFCC Part 15.247 Test MethodDTS: KDB 558074 D01 V05 - Chapter 8.3.1.1 RBW ≥ DTS Bandwidth Class / TC VersionTC_VM_FCC15247_Maximum_Peak_Conducted_Output_Power_DTS_V01 Version: 0.0.1 My DescriptionFCC 15.247 Maximum Peak Output Power Conducted DTS - BT LE 1 Msps Add. Information Test Parameter Technology to testBT LE 1 Msps Antenna Port used1 Temperaturemid Voltagemid Frequency low to testTrue | Freq [MHz] 2402 Frequency mid to testTrue | Freq [MHz] 2440 Frequency high to testTrue | Freq [MHz] 2480 Switched PathIUT - SignalingUnit - SpectrumAnalyzer Devices in useSigBT: Rohde&Schwarz,CMW,1201.0002k75/100683,3.7.170 | SA: Rohde&Schwarz,FSV-30,1321.3008K30/103809,3.60 Document No. 1-9206/19-01-06_Annex_MR_A_14/123 Test at TX 2402 MHz DTM Connection check Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Connection result------------PASS READ SA SETTINGS: RefLevel [dBm] | RefLevelOffset [dB] | InpAtt [dB]13.39 | 10.09 | 20 Start [MHz] | Stop [MHz]2401.000 | 2403.000 RBW [MHz] | VBW [MHz]0.100000 | 0.300000 Detector | TraceModePOS | MAXH Sweep: Time [ms] | Count | Points per Section | Type50 | 200 | 10001 | SWE DTS Bandwidth Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict DTS Bandwidth (6dB)------697kHzINFO Plot_FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE 1 Msps DTS BW_16032020_134608.png READ SA SETTINGS: RefLevel [dBm] | RefLevelOffset [dB] | InpAtt [dB]18.39 | 10.09 | 25 Start [MHz] | Stop [MHz]2401.000 | 2403.000 RBW [MHz] | VBW [MHz]1.000000 | 5.000000 Detector | TraceModePOS | MAXH Sweep: Time [ms] | Count | Points per Section | Type50 | 200 | 1001 | SWE RESULT Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Peak Power---30.008.38dBmPASS Peak Power---10006.886523mWPASS Frequency at Peak------2401.734MHzINFO Document No. 1-9206/19-01-06_Annex_MR_A_15/123 Plot_FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE 1 Msps_16032020_134624.png Document No. 1-9206/19-01-06_Annex_MR_A_16/123 Test at TX 2440 MHz DTM Connection check Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict Connection result------------PASS READ SA SETTINGS: RefLevel [dBm] | RefLevelOffset [dB] | InpAtt [dB]13.46 | 10.1 | 20 Start [MHz] | Stop [MHz]2439.000 | 2441.000 RBW [MHz] | VBW [MHz]0.100000 | 0.300000 Detector | TraceModePOS | MAXH Sweep: Time [ms] | Count | Points per Section | Type50 | 200 | 10001 | SWE DTS Bandwidth Test DescriptionLower LimitUpper LimitMeasuredUnitVerdict DTS Bandwidth (6dB)------699kHzINFO Plot_FCC Part 15.247 Maximum Peak Conducted Output Power DTS ~ BT LE 1 Msps DTS BW_16032020_134655.png READ SA …

Text truncated - open the document above for the full version.

T2 20dB---2483.5000002480.5736MHzPASS Plot_FCC Part 15.247 Bandwidth 99PCT-20dB ~ BT LE coded S2 20dB_16032020_151144.png Plot_FCC Part 15.247 Bandwidth 99PCT-20dB ~ BT LE coded S2_16032020_151148.png TEST FINISHED General Verdict16.03.2020 15:11:48 / RT: 135 sPASS Document No. 1-9206/19-01-06_Annex_MR_A_191/123 17. FCC Part 15.247 TX Spurious Conduced ~ BT LE 1 Msps Test References TC Start16.03.2020 1…

Text truncated - open the document above for the full version.