T7V9019Wi-Fi 6 Dual Band 2.4 GHz/5 GHz, Bluetooth and 802.15.4 Module

Wireless Connectivity PAN9019 / PAN9019A Wi-Fi 6 Dual Band 2.4 GHz/5 GHz, Bluetooth ® and 802.15.4 (PAN9019A only) Module Module Integration Guide Rev. 1.0  PAN9019 / PAN9019A Wi-Fi and Bluetooth Module 1 About This Document Module Integration Guide Rev. 1.0 Page 2 of 52 Overview The PAN9019 and PAN9019A are 2.4 GHz and 5 GHz ISM band Wi-Fi, Bluetooth, and 802.15.4 1 radio modules, which allow easy integration of Wi-Fi, Bluetooth, and 802.15.4 1 based technologies into various electronic devices. Features • Dual band 2.4 GHz and 5 GHz 802.11 a/b/g/n/ac/ax Wi-Fi, Bluetooth, and 802.15.4 1 combo module • Supports WPA3 security • Secured boot and firmware • 802.11e Quality of Service is supported for multimedia application • IEEE 802.11ax, 1×1 spatial stream with data rates up to 600 Mbps (MCS11, 80 MHz channel bandwidth) • OFDMA (UL/DL) and MU-MIMO (UL/DL) • Bluetooth 5.4 (including LE and long range) • WCI-2- and 5-wire PTA coexistence interfaces • Generic interfaces include SDIO 3.0, high-speed UART and SPI 2 for host processor connection • OS driver support for RTOS, Linux ® , and Android ™ Characteristics • Surface Mount Type (SMT): 15.3 mm × 12 mm × 2.5 mm • PAN9019: NXP ® IW611 WLAN 2.4 GHz and 5 GHz, Bluetooth single-chip solution inside • PAN9019A: NXP IW612 WLAN 2.4 GHz and 5 GHz, Bluetooth and 802.15.4 single-chip solution inside • Rx sensitivity: -98 dBm at IEEE 802.11b 1 Mbps • IEEE 802.11ax 20 MHz, 40 MHz, 80 MHz channel bandwidth • Power supply: 1.8 V and 3.3 V • SDIO 1 bit or 4 bit • Wide temperature range: -40 °C to 85 °C Block Diagram 1 802.15.4 is only supported by the PAN9019A module. 2 SPI is available as 802.15.4 host interface (only on PAN9019A module).  PAN9019 / PAN9019A Wi-Fi and Bluetooth Module 1 About This Document Module Integration Guide Rev. 1.0 Page 3 of 52  PAN9019 / PAN9019A Wi-Fi and Bluetooth Module 1 About This Document Module Integration Guide Rev. 1.0 Page 4 of 52 By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Module Integration Guide before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2024. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Module Integration Guide does not lodge the claim to be complete and free of mistakes. If this document is marked as preliminary, please be aware that its final content is not yet concluded and the use of it is at your own risk. Engineering Samples (ES) If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. Disclaimer The customer acknowledges that samples may deviate from the Module Integration Guide and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by: • The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, • Deviation or lapse in function of the Engineering Sample, • Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager. The information contained herein is presented only as guidance for Product use. No responsibility is assumed by Panasonic for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. Description of hardware, software, and other information in this document is only intended to illustrate the functionality of the referred Panasonic product. It should not be construed as guaranteeing specific functionality of the product as described or suitable for a particular application. Any provided (source) code shall not be used or incorporated into any products or systems whose manufacture, use or sale is prohibited under any applicable laws or regulations. Any outlined or referenced (source) code within this document is provided on an “as is” basis without any right to technical support or updates and without warranty of any kind on a free of charge basis according to § 516 German Civil Law (BGB) including without limitation, any warranties or conditions of title, non infringement, merchantability, or fitness for a particular purpose. Customer acknowledges that (source) code may bear defects and errors.  PAN9019 / PAN9019A Wi-Fi and Bluetooth Module 1 About This Document Module Integration Guide Rev. 1.0 Page 5 of 52 The third-party tools mentioned in this document are offered by independent third-party providers who are solely responsible for these products. Panasonic has no responsibility whatsoever for the performance, product descriptions, specifications, referenced content, or any and all claims or representations of these third-party providers. Panasonic makes no warranty wha…

Text truncated - open the document above for the full version.

Wireless Connectivity PAN9019A Wi-Fi 6 Dual Band 2.4 GHz/5 GHz, Bluetooth ® and 802.15.4 Module Product Specification Rev. 1.0 PAN9019A Wi-Fi, Bluetooth and 802.15.4 Module Product Specification Rev. 1.0 Page 2 of 141 Overview The PAN9019A is a 2.4 GHz and 5 GHz ISM band Wi-Fi, Bluetooth ® , and 802.15.4 radio module, which allows easy integration of Wi-Fi, Bluetooth, and 802.15.4 based technologies into various electronic devices. Features • Dual band 2.4 GHz and 5 GHz 802.11 a/b/g/n/ac/ax Wi-Fi, Bluetooth ® , and 802.15.4 combo module • Supports WPA3 personal and enterprise security • Authenticated and secured boot • 802.11e Quality of Service is supported for multimedia application • IEEE 802.11ax, 1×1 spatial stream with data rates up to 600 Mbps (MCS11, 80 MHz channel bandwidth) • OFDMA (UL/DL) and MU-MIMO (UL/DL) • Bluetooth 5.4 • WCI-2 and 5-wire PTA coexistence interfaces • Generic interfaces include SDIO 3.0 and high-speed UART for host processor connection • OS driver support for RTOS, Linux ® , and Android ® Characteristics • Surface Mount Type (SMT): 15.3 mm × 12 mm × 2.5 mm • NXP ® IW612 WLAN 2.4 GHz and 5 GHz, Bluetooth and 802.15.4 single-chip solution inside • Rx sensitivity: -98 dBm at IEEE 802.11b 1 Mbps • IEEE 802.11ax 20 MHz, 40 MHz, 80 MHz channel bandwidth • Power supply: 1.8 V and 3.3 V • SDIO 1 bit or 4 bit • Wide temperature range: -40 °C to 85 °C Block Diagram RF Pad SDIO (Wi-Fi) Crystal 40 MHz NXP ® IW612 Radio SoC PAN9019A Wi-Fi, Bluetooth® and 802.15.4 Radio M odule IEEE 802.11 a/b/g/n/ac/ax Bluetooth 5.4 (BR, EDR, Low Energy) IEEE 802.15.4-2015 2.4 GHz UART (BT) GPIO PDn I²S/PCM COEX V 1V8 V 3V3 SPDT Diplexer HBLB C V IO /V IOSD RF SW SPI (802.15.4) PAN9019A Wi-Fi, Bluetooth and 802.15.4 Module Product Specification Rev. 1.0 Page 3 of 141 By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2024. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Product Specification does not lodge the claim to be complete and free of mistakes. If this document is marked as preliminary, please be aware that its final content is not yet concluded and the use of it is at your own risk. Document Acceptance By signing the Product Specification, you acknowledge that you are a legal representative for your company and that you understand and accept the validity of the contents herein. If the signed version of the Product Specification has not been returned to Panasonic within 30 days after receipt of the product, the specification or approval sheet shall be deemed to be accepted by you. Engineering Samples (ES) If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. Disclaimer The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by: • The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, • Deviation or lapse in function of the Engineering Sample, • Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager. PAN9019A Wi-Fi, Bluetooth and 802.15.4 Module Product Specification Rev. 1.0 Page 4 of 141 Table of Contents 1 About This Document ......................................................................................................................... 6 1.1 Purpose and Audience .............................................................................................................. 6 1.2 Revision History ......................................................................................................................... 6 1.3 Use of Symbols ......................................................................................................................... 7 1.4 Related Documents ................................................................................................................... 7 2 Overview .............................................................................................................................................. 8 2.1 Block Diagram ........................................................................................................................... 9 2.2 Pin Configuration ..................................................................................................................... 10 2.3 Host Interface .......................................................................................................................... 14 2.4 Audio-Interfaces ..............................................................................................................…

Text truncated - open the document above for the full version.

Wireless Connectivity PAN9019 Wi-Fi 6 Dual Band 2.4 GHz/5 GHz and Bluetooth ® Module Product Specification Rev. 1.0 PAN9019 Wi-Fi and Bluetooth Module Product Specification Rev. 1.0 Page 2 of 136 Overview The PAN9019 is a 2.4 GHz and 5 GHz ISM band Wi-Fi and Bluetooth ® radio module, which allows the easy integration of Wi-Fi and Bluetooth based technologies into various electronic devices. Features • Dual band 2.4 GHz and 5 GHz 802.11 a/b/g/n/ac/ax Wi-Fi and Bluetooth ® combo module • Supports WPA3 personal and enterprise security • Authenticated and secured boot • 802.11e Quality of Service is supported for multimedia application • IEEE 802.11ax, 1×1 spatial stream with data rates up to 600 Mbps (MCS11, 80 MHz channel bandwidth) • OFDMA (UL/DL) and MU-MIMO (UL/DL) • Bluetooth 5.4 • WCI-2 and 5-wire PTA coexistence interfaces • Generic interfaces include SDIO 3.0 and high-speed UART for host processor connection • OS driver support for RTOS, Linux ® , and Android ® Characteristics • Surface Mount Type (SMT): 15.3 mm × 12 mm × 2.5 mm • NXP ® IW611 WLAN 2.4 GHz and 5 GHz and Bluetooth ® single-chip solution inside • Rx sensitivity: -98 dBm at IEEE 802.11b 1 Mbps • IEEE 802.11ax 20 MHz, 40 MHz, 80 MHz channel bandwidth • Power supply: 1.8 V and 3.3 V • SDIO 1 bit or 4 bit • Wide temperature range: -40 °C to 85 °C Block Diagram RF Pad SDIO (Wi - Fi) Crystal 40 MHz NXP ® IW611 Radio SoC PAN9019 Wi - Fi and Bluetooth® Radio M odule IEEE 802.11 a/b/g/n/ac/ax Bluetooth 5.4 (BR, EDR, Low Energy) UART (BT) GPIO PDn I ² S/PCM COEX V 1V8 V 3V3 SPDT Diplexer HB LB C V IO /V IOSD RF SW PAN9019 Wi-Fi and Bluetooth Module Product Specification Rev. 1.0 Page 3 of 136 By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2024. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Product Specification does not lodge the claim to be complete and free of mistakes. If this document is marked as preliminary, please be aware that its final content is not yet concluded and the use of it is at your own risk. Document Acceptance By signing the Product Specification, you acknowledge that you are a legal representative for your company and that you understand and accept the validity of the contents herein. If the signed version of the Product Specification has not been returned to Panasonic within 30 days after receipt of the product, the specification or approval sheet shall be deemed to be accepted by you. Engineering Samples (ES) If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. Disclaimer The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by: • The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, • Deviation or lapse in function of the Engineering Sample, • Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager. PAN9019 Wi-Fi and Bluetooth Module Product Specification Rev. 1.0 Page 4 of 136 Table of Contents 1 About This Document ......................................................................................................................... 6 1.1 Purpose and Audience .............................................................................................................. 6 1.2 Revision History ......................................................................................................................... 6 1.3 Use of Symbols ......................................................................................................................... 7 1.4 Related Documents ................................................................................................................... 7 2 Overview .............................................................................................................................................. 8 2.1 Block Diagram ........................................................................................................................... 9 2.2 Pin Configuration ..................................................................................................................... 10 2.3 Host Interface .......................................................................................................................... 14 2.4 Audio-Interfaces ...................................................................................................................... 15 2.5 Coexistence ......................................................................................................…

Text truncated - open the document above for the full version.

Panasonic Industrial Devices Europe GmbH Zeppelinstraße 19, 21337 Lüneburg Phone +49 (0) 4131 899-0 Fax +49 (0) 4131 899-120 E-Mail: [email protected] www.pideu.panasonic.de Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 3/18/2024 To whom it may concern: We, Panasonic Industrial Devices Europe GmbH, hereby certify that the equipment for which authorization is sought (FCC ID: T7V9019) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely --------------------------------------- (signature) Panasonic Industrial Devices Europe GmbH FRN: 0014980072 Zeppelinstraße 19 21337 Lüneburg Germany Marcus Nottorf +49 (0) 4131-899 435 [email protected]

PANASONIC INDUSTRIAL DEVICES EUROPE GmbH Zeppelinstraße 19, 21337 Lüneburg Provided by Eurofins Product Service GmbH v.0.2 Telefon +49 (0) 4131 899-0 Telefax +49 (0) 4131 899-120 E-Mail: [email protected] www.pideu.panasonic.de Modular Approval Request Letter Date: 2024-03-18 FCC ID: T7V9019 Type of Equipment: Wi-Fi 6 Dual Band 2.4 GHz/5 GHz, Bluetooth® and 802.15.4 Module Herewith we state that the requirements according to FCC Part 15.212 are met and the module qualifies for a single modular transmitter approval. # Requirement as per 47 CFR Part 15 Subpart C §15.212 Conditions met? (Y/N) Realisation / Evidence in FORM 731 application filing i RF shielding The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Y The radio portion has his own shielding (see external photos). ii Buffered modulation/data inputs The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. Y The function has been integrated in the chipset (see operational description) iii Power supply regulation The modular transmitter must have its own power supply regulation. Y The function has been integrated in the chipset (see operational description) iv Antenna requirements The modular transmitter must comply with the antenna and transmission system requirements of §§15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). Additional justification and details may be requested – please refer to KDB 996369 Y The module comes with one permanently attached antenna. The spurious emission requirements are fulfilled (see attached test report). v Stand-alone test configuration The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in §15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see §15.31(i)). Y The module has been tested in a stand-alone configuration (see test report/ test set-up photos) vi Labelling The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. Y The module has its own label The FCC ID is shown in the User Manual. The instruction for labelling rules for the host device has been stated in the user manual vii Compliance on specific rule or operating requirements The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such Y The required FCC rules has been fulfilled and all instructions for maintaining compliance has been clearly stated in the user manual PANASONIC INDUSTRIAL DEVICES EUROPE GmbH Zeppelinstraße 19, 21337 Lüneburg Provided by Eurofins Product Service GmbH v.0.2 Telefon +49 (0) 4131 899-0 Telefax +49 (0) 4131 899-120 E-Mail: [email protected] www.pideu.panasonic.de requirements. A copy of these instructions must be included in the application for equipment authorization. viii RF Exposure Radio frequency devices operating under the provisions of this part are subject to the radio frequency radiation exposure requirements specified in §§1.1307(b), 1.1310, 2.1091, and 2.1093 of this chapter, as appropriate. Applications for equipment authorization of modular transmitters under this section must contain a statement confirming compliance with these requirements. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Y RF exposure requirements are fulfilled for mobile configuration. The installation of the module is restricted to mobile host devices what is clearly stated in the installation instruction of the user manual. For portable applications OEM integrators need SAR evaluation and an own FCC ID. Marcus Nottorf Safety Manager Panasonic Industrial Devices Europe GmbH Zeppelinstraße 19 21337 Lüneburg Germany

Panasonic Industrial Devices Europe GmbH Zeppelinstraße 19, 21337 Lüneburg Phone +49 (0) 4131 899-0 Fax +49 (0) 4131 899-120 E-Mail: [email protected] www.pideu.panasonic.de Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 4/10/2024 Declaration To whom it may concern: We, Panasonic Industrial Devices Europe GmbH, hereby certify that the equipment for which authorization is sought (FCC ID: T7V9019) underwent testing on the evaluation board iMX8M Mini Developer’s Kit V3 (EAK00393) and reference design with a reference trace to the antenna port. Both the evaluation board and reference design with reference trace aimed to minimize any impact on the module's performance. Consequently, we are confident that, within the specified design constraints, we have diligently met this requirement. This gives us a high level of assurance that the module will demonstrate compliance when operating in a stand-alone configuration. By signing this form, we confirm the above and that we are aware of the application requirements listed under 47 CFR Part 15 Subpart C §15.212. Sincerely, Signature Marcus Nottorf Safety Manager Panasonic Industrial Devices Europe GmbH Zeppelinstraße 19 21337 Lüneburg

I I I l Panuonlc lndustrlll Devlen Europe GmbH ZeppelinstraQe 19 1 21337 Lon.burg Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7 435 Oakland Mills Road Columbia, MD 21046 u,s. Agent Designation Panasonic Ref: PIDEU-24-F001 Phone +49 (0) 4131 899-0 Fax +49 (0) 4131 899-120 E-Mail: [email protected] www.pideu.pennonic.de 3/21/2024 Panasonic Industrial Devices Europe GmbH acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: T7V9019): Panasonic Corporation of North America acknowledges their obligation to accept service of process on behalf of Panasonic Industrial Devices Europe GmbH. Panasonic Industrial Devices Europe GmbH with the FRN 0014980072 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the condusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under§ 2.911 (d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 9Bo446 001. /.r expirabon date tor this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify :ne FCC within 30 days via the granting TCB. S1'lcerely Panasonic Industrial Devices Europe GmtH ZeppclinstraBe 19 D - 21337 Luneburo Panasonic Industrial Devices Euro e GmbH FRN: 0014980072 ZeppelinstraBe 19 21337 LOneburg German Marcus Nottorf +49 0 4131-899 435 Marcus.Nottorf eu. anasonic.com Panasonic Co oration of North America FRN: 0003762242 Two Riverfront Plaza, Newark, NJ 07102-5490 USA Ben Botros +1201-348-7760 Ben.Botros us. anasonic.com

Provided by Eurofins Product Service GmbH v.0. 2 PANASONIC INDUSTRIAL DEVICES EUROPE GmbH Zeppelinstraße 19, 21337 Lüneburg Declaration concerning Antenna Specification It is hereby declared that the product Model No.: ENWF9511C1KF, ENWF9501C1KF FCC ID: T7V9019 fulfils the requirement in FCC test relating to the antenna type. The device specified above confirms to the FCC recommendations for internal or external antenna type described below: Telefon +49 (0) 4131 899-0 Telefax +49 (0) 4131 899-120 E-Mail: [email protected] www.pideu.panasonic.de Provided by Eurofins Product Service GmbH v.0. 2 Provided by Eurofins Product Service GmbH v.0. 2 The mounting of the antennas is fixed to the radio module and no other antenna should be used. Company name: Panasonic Industrial Devices Europe GmbH Address: Zeppelinstrasse 19 City: Lüneburg ZIP / Postal code: 21337 Country: Germany Place: Lüneburg Date: 2024-03-18 Signature:

Panasonic Industrial Devices Europe GmbH Zeppelinstraße 19, 21337 Lüneburg Phone +49 (0) 4131 899-0 Fax +49 (0) 4131 899-120 E-Mail: [email protected] www.pideu.panasonic.de 1/2 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 3/20/2024 Request for Confidentiality Company name: Panasonic Electronic Devices Europe GmbH FCC ID: T7V9019 In accordance with CFR 47 §0.457(d) and CFR 47 §0.459 of the Commission’s Rules, Panasonic Electronic Devices Europe GmbH hereby requests confidentiality of following exhibits: Exhibit Type: Type of Confidentiality Requested Detailed block diagrams* Long-term confidentiality Schematic diagrams* x Long-term confidentiality Detailed operational descriptions* x Long-term confidentiality (only SW Security Declaration U- NII_FCC) Parts lists/ tune up information* x Long-term confidentiality External photos Short-term confidentiality** Internal photos Short-term confidentiality** Test setup photos Short-term confidentiality** User’s manual Short-term confidentiality** Short-term maximum confidentiality period: 180 days OR: Short-term confidentiality release date (product launch): MM/DD/YYYY * Exhibits not routinely made available to the public. ** Only if applicable: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. When the device is marketed the grantee must inform the TCB to release the Short-Term Confidentiality information withhe…

Text truncated - open the document above for the full version.