
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
D Handsender WARNUNG Es besteht möglicherweise Verletzungs- oder Lebens- gefahr, wenn wichtige Sicherheitshinweise nicht beachtet werden. Beachten Sie alle Hinweise in dieser Anleitung und zusätzlich alle Hinweise in der Anlei- tung des Antriebes. Weisen Sie auch alle weite- ren Benutzer auf diese Anleitungen hin. An diesem Gerät dürfen keine Veränderungen vorge- nommen werden. Die Betriebserlaubnis erlischt, falls trotzdem Veränderungen an diesem Gerät vorgenom- men werden, die nicht in die- ser Anleitung beschrieben oder vom Hersteller geneh- migt sind. Dieses Gerät erfüllt die For- derungen der FCC Regelun- gen Teil 15. Das Betreiben des Gerätes unterliegt den folgenden beiden Bedingun- gen: (1) dieses Gerät darf keine beeinträchtigenden Störun- gen verursachen, und (2) dieses Gerät muß jede Störungen akzeptieren, ein- schließlich Störungen, die den Betrieb beeinträchtigen können. Funktionsweise Mit diesem Funk-Handsender kann ein elektrisch betriebe- ner Antrieb gesteuert werden um Sektionaltore oder Schwingtore zu öffnen und zu schließen. EN Hand-held transmitter WARNING There is a possible risk of injury or even the risk of death if important safety information is not observed and complied with. Observe and comply with all information in this manual and additionally all information in the manual of the drive. You must also inform all additional users about this manual. No modifications to this device are allowed. The operating license expires if modifications are performed on this device that are not described in this manual or authorized by the manufactu- rer. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera- tion. Mode of operation Using this radio remote con- trol, an electrically powered drive can be controlled for opening and closing sectional doors or swinging doors. Technical specifica- tions Radio frequency 315 MHz Temperature range –14 °F to +158 °F (–10 °C to +70 °C) Range Approx. 100 ft (30 m), depen- ding on surrounding conditi- ons Current consumption Approx. 10 mA Battery (supplied) Type CR 2032, 3 V Dimensions (slid together) 3 7/16” x 15/16” x 11/16” (87 x 24 x 17 mm) Weight Approx. 30 g (including bat- tery) Learning the remote control In order to open, close or stop the drive using the hand- held remote control, the drive has to "learn" the code first. The radio code of the hand- held remote control is trans- mitted to the receiver (in the drive). You can allocate a desired remote button for this. Plug in the power plug into the power outlet or Radio Power Status Safety Command Reset LearnLearn 2 1 14 15 16 Radio Power Status Safety Command Reset LearnLearn 13 3 4 5 6 2 11 Switch on the the electrical supply for a direct electri- cal connection (switch on the circuit breaker or fuse). When the opener is first con- nected to the mains supply, the opener lighting blinks. Learning the radio code Press the learn button (1) in the controller housing. The LED (Radio) lights up. Press a desired hand-held remote control button (2). The LED (Radio) flashes briefly . – When the LED (Radio) lights up for a second, the hand-held remote control control has been learned. – When the LED (Radio) blinks three times, all button locations are already occupied. Programming additional hand-held remote controls: Repeat the above steps. A maximum of 20 button locati- ons for each radio receiver are available. Lighting function In order to be able to switch the lighting on the drive on or off separately using the hand- held remote control, a second remote control button function has to be "learned in". Press the learn button (1) in the controller housing twice. The LED (Radio) briefly blinks two times. Press a desired hand-held remote control button (2). Radio Power Status Safety Command Reset LearnLearn 2 1 14 15 16 Radio Power Status Safety Command Reset LearnLearn 13 3 4 5 6 2 11 – When the LED (Radio) lights up for a second, the hand-held remote control control has been learned. – When the LED (Radio) blinks three times, all button locations are already occupied. Other functions Depending on the DIP switch settings, other functions such as “partial opening” or “defi- ned operation” can be “lear- ned in” to a second hand- held remote in the same way. See chapter “Settings”. Aborting the learn process Press the learn button (1) in the controller housing until no LED lights up. If no radio code is received within 10 seconds, the learning process is inter- rupted and has to be started again if necessary. Deleting a learned radio code Press the learn button (1) in the controller housing for at least five seconds until the LED (Radio) blinks slowly. Press the desired remote control button. The LED (Radio) lights up for a second. When the LED (Radio) 2 1 14 15 16 Radio Power Status Safety Command Reset LearnLearn 13 3 4 5 6 Radio Power Status Safety Command Reset LearnLearn 11 2 1 14 15 16 Radio Power Status Safety Command Reset LearnLearn 13 3 4 5 6 Radio Power Status Safety Command Reset LearnLearn 11 turns off, the radio code of this hand-held remote con- trol button is deleted. Deleting all learned radio codes Press the learn button (1) and hold it until – the LED (Radio) initially blinks for five seconds, – and then slowly blinks for ten seconds – and subsequently blinks quickly for ten seconds. When the LED turns off, all radio codes are dele- ted. If the learn button is released prior to this, the radio codes are not deleted. Operation WARNING There is the possible risk of injury or death if you do not observe and comply with the following information. Therefore, observe and comply with all listed instructions before opera- ting. Only operate the remote con- trol when you have direct line of sight to the door and no persons or objects are loca- ted in the …
Text truncated - open the document above for the full version.
Sommer Antriebs- und Funktechnik GmbH Address: Hans-Böckler-Straße 21-27 D-73230 Kirchheim/Teck Phone: +49 (0)7021/ 8001-411 Fax: +49 (0)7021/ 8001-403 Manufacturer of radiocontrolled operators for garage doors with accessories Your ref. Your message from Our ref. dsz Date 17.10.2006 page 1 of 1 Department : Entwicklung / (Development) / Schwarz, Dominik E-Mail : [email protected] http://www.sommer.eu Sommer Antriebs- und Funktechnik GmbH, Hans-Böckler-Str. 21-27, D-73230 Kirchheim/Teck Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. SOMMER Antriebs- u. Funktechnik GmbH would like the following documents regarding this submission for FCC ID: T8C001 to be kept confidential. 04_OpDes_BlkDia.pdf 05_Schem.pdf. The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely,
Type TX03-315-4 FCC ID T8C001 / IC: 6496A-001 Abteilung: Entwicklung / (Development) erstellt am: 28.09.2006 erstellt von: Schwarz, Dominik Verteiler: Seite von 1 1 Front view, Front view, Rear view, Rear view open position closed position open position closed position The device identifier is on the rear side of the device engraved into the mould of the plastic part. Picture of the device identifier:
Type TX03-315-4 FCC ID T8C001 / IC: 6496A-001 Abteilung: Entwicklung / (Development) erstellt am: 28.09.2006 erstellt von: Schwarz, Dominik Verteiler: Seite von 1 1 Front view, Front view, Rear view, Rear view open position closed position open position closed position The device identifier is on the rear side of the device engraved into the mould of the plastic part. Picture of the device identifier:
Type TX03-315-4 FCC ID T8C001 / IC: 6496A-001 Abteilung: Entwicklung / (Development) erstellt am: 17.10.2006 erstellt von: Schwarz, Dominik Verteiler: Seite von 1 1 Front View: Rear View:
FCC-ID: T8C001 RADIO LABORATORIES EMC LABORATORIES DAT-P-204/95 EMCC DR. RAĹ EK Moggast, Boelwiese 8 91320 Ebermannstadt Germany FCC Registration # 90566 Annex2_AA.doc Telephone: +49-9194-9016 Telefax: +49-9194-8125 Mail: [email protected] Web: http://www.emcc.de PAGE 1 of 5 ANNEX 2 TO TEST REPORT # EMCC-950432.1AA, 2006-MAY-26 PHOTOGRAPHS OF TEST SAMPLE EQUIPMENT UNDER TEST: Name: 4-command transmitter AM 315 MHz Model: TX03-315-4 Serial No: 100072 Equipment Category: Transmitter Manufacturer: SOMMER Antriebs- und Funktechnik GmbH Address: Hans-Boeckler-Strasse 21-27 73230 Kirchheim / Teck Germany Phone: ++49-7021-8001-0 Fax: ++49-7021-8001-403 RELEVANT STANDARD: 47 CFR Part 15C - Intentional Radiators CONTENTS Page 1 External view ........................................................................................................................................................2 1.1 Photograph: Front view ..............................................................................................................................2 1.2 Photograph: Rear view...............................................................................................................................3 2 Internal view .........................................................................................................................................................4 2.1 Photograph: Side 1 of PCB ........................................................................................................................4 2.2 Photograph: Side 2 of PCB ........................................................................................................................5 FCC-ID: T8C001 Annex 2 to Test Report #EMCC-950432.1AA Page 2 of 5 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX2_AA.DOC 1 EXTERNAL VIEW 1.1 Photograph: Front view FCC-ID: T8C001 Annex 2 to Test Report #EMCC-950432.1AA Page 3 of 5 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX2_AA.DOC 1.2 Photograph: Rear view FCC-ID: T8C001 Annex 2 to Test Report #EMCC-950432.1AA Page 4 of 5 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX2_AA.DOC 2 INTERNAL VIEW 2.1 Photograph: Side 1 of PCB FCC-ID: T8C001 Annex 2 to Test Report #EMCC-950432.1AA Page 5 of 5 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX2_AA.DOC 2.2 Photograph: Side 2 of PCB
FCC-ID: T8C001 Test Report #EMCC-950432.1AA Page 2 of 19 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS REPORT_AA.DOC EMCC DR. RAŠEK ™ CONTENTS Page 1 GENERAL INFORMATION ...................................................................................................................................................................3 1.1 Purpose..................................................................................................................................................................................3 1.2 Limits and Reservations ......................................................................................................................................................3 1.3 Test Location.........................................................................................................................................................................3 1.4 Manufacturer .........................................................................................................................................................................3 1.5 Dates ......................................................................................................................................................................................3 2 Product Description.............................................................................................................................................................................4 2.1 Equipment Under Test (EUT)...............................................................................................................................................4 2.2 EUT Peripherals ....................................................................................................................................................................4 2.3 Mode of Operation During Testing .....................................................................................................................................4 2.4 Modifications Required for Compliance ............................................................................................................................4 3 Test Results Summary ........................................................................................................................................................................5 4 Antenna Requirement ..........................................................................................................................................................................6 4.1 Regulation .............................................................................................................................................................................6 4.2 Result .....................................................................................................................................................................................6 5 Radiated Emissions TEST...................................................................................................................................................................7 5.1 Regulation .............................................................................................................................................................................7 5.2 Test Equipment .....................................................................................................................................................................8 5.3 Test Procedures....................................................................................................................................................................8 5.4 Calculation of Field Strength Limits ...................................................................................................................................9 5.5 Calculation of Average Correction Factor .........................................................................................................................9 5.6 Field Strength Calculation ...................................................................................................................................................9 5.7 Test Results.........................................................................................................................................................................11 5.7.1 Magnetic Field (f = 1.7 MHz to 30 MHz) .....................................................................................................................11 5.7.2 Electric Field (f = 30 MHz to 3.2 GHz) ........................................................................................................................12 6 Conducted Emissions Tests .............................................................................................................................................................14 6.1 Regulation ...........................................................................................................................................................................14 6.2 Test Equipment ...................................................................................................................................................................14 6.3 Test Procedures..................................................................................................................................................................14 6.4 Test Results.........................................................................................................................................................................14 7 Periodic Operation Characteristics..................................................................................................................................................15 7.1 Periodic Operation.....................................…
Text truncated - open the document above for the full version.
FCC-ID: T8C001 RADIO LABORATORIES EMC LABORATORIES DAT-P-204/95 EMCC DR. RAĹ EK Moggast, Boelwiese 8 91320 Ebermannstadt Germany FCC Registration # 90566 Annex1_AA.doc Telephone: +49-9194-9016 Telefax: +49-9194-8125 Mail: [email protected] Web: http://www.emcc.de Page 1 of 7 ANNEX 1 TO TEST REPORT # EMCC-950432.1AA, 2006-MAY-26 PHOTOGRAPHS OF TEST SETUPS EQUIPMENT UNDER TEST: Name: 4-command transmitter AM 315 MHz Model: TX03-315-4 Serial No: 100072 Equipment Category: Transmitter Manufacturer: SOMMER Antriebs- und Funktechnik GmbH Address: Hans-Boeckler-Strasse 21-27 73230 Kirchheim / Teck Germany Phone: ++49-7021-8001-0 Fax: ++49-7021-8001-403 RELEVANT STANDARD: 47 CFR Part 15C - Intentional Radiators CONTENTS Page 1 CONDUCTED EMISSIONS TEST .........................................................................................................................2 1.1 Photograph: none.......................................................................................................................................2 2 RADIATED EMISSIONS TEST .............................................................................................................................3 2.1 Photograph: Magnetic field (H-field), f < 30 MHz, EUT vertical .................................................................3 2.2 Photograph: Electric field, f = 30 MHz to 1 GHz, EUT vertical...................................................................4 2.3 Photograph: Electric field, f = 30 MHz to 1 GHz, EUT horizontal ..............................................................5 2.4 Photograph: Electric field, f > 1 GHz, EUT vertical ....................................................................................6 3 BANDWIDTH TEST...............................................................................................................................................7 3.1 Photograph: EUT in test fixture ..................................................................................................................7 FCC-ID: T8C001 Annex 1 to Test Report #EMCC-950432.1AA Page 2 of 7 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX1_AA.DOC 1 CONDUCTED EMISSIONS TEST 1.1 Photograph: none not applicable FCC-ID: T8C001 Annex 1 to Test Report #EMCC-950432.1AA Page 3 of 7 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX1_AA.DOC 2 RADIATED EMISSIONS TEST 2.1 Photograph: Magnetic field (H-field), f < 30 MHz, EUT horizontal FCC-ID: T8C001 Annex 1 to Test Report #EMCC-950432.1AA Page 4 of 7 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX1_AA.DOC 2.2 Photograph: Electric field, f = 30 MHz to 1 GHz, EUT vertical FCC-ID: T8C001 Annex 1 to Test Report #EMCC-950432.1AA Page 5 of 7 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX1_AA.DOC 2.3 Photograph: Electric field, f = 30 MHz to 1 GHz, EUT horizontal FCC-ID: T8C001 Annex 1 to Test Report #EMCC-950432.1AA Page 6 of 7 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX1_AA.DOC 2.4 Photograph: Electric field, f > 1 GHz, EUT vertical FCC-ID: T8C001 Annex 1 to Test Report #EMCC-950432.1AA Page 7 of 7 Issue Date: 2006-MAY-26 TEST OF SOMMER ANTRIEBS- UND FUNKTECHNIK GMBH MODEL TX03-315-4 TO 47 CFR PART 15C - INTENTIONAL RADIATORS ANNEX1_AA.DOC 3 BANDWIDTH TEST 3.1 Photograph: EUT in test fixture
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15.231 | 315 MHz - 315 MHz | - |

Receiver Module, e.g. garage door operator
Equipment Class
CYY - Communications Receiver used w/Pt 15 Transmitter
Remote Control Transmitter
Equipment Class
DSC - Part 15 Security/Remote Control Transmitter
Remote Control Transmitter
Equipment Class
DSC - Part 15 Security/Remote Control Transmitter
Remote Control Transmitter
Equipment Class
DSC - Part 15 Security/Remote Control Transmitter
Telecody - Keypad Transmitter
Equipment Class
DSC - Part 15 Security/Remote Control Transmitter