TE7CPE2102.4 GHz 300Mpbs 9dBi Outdoor CPE

Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520 CONTENTS Hardware Connection Overview Software Configuration Antenna Alignment Specifications Frequently Asked Questions (FAQ) Site Consideration 4 6 8 9 10 10 16 17 18 14 14 Ethernet Cable Selection Connection and Installation Lightning & ESD Protection Login to Pharos Configuration for Typical Application • Point-to-Point 4 Overview • Package Contents • LED Explanation Pharos CPEPassive PoE Adapter Pole Mounting Straps Installation Guide Power Cord AP/AP Router mode: All the four LEDS are steady light Client/Bridge/Repeater/AP Client Router mode: More lighted LEDs indicate better wireless signal strength On: A device is connected to this port, but there is no activity Flashing: A device is connected to this port, and is active On: The CPE is powered on. POWE R LAN0 LAN1 TP-LINK's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to products including CPE210, CPE220, CPE510 and CPE520. 5 • Panel Layout Grouding Terminal Pharos CPE: Passive PoE Adapter: Shielded Ethernet Port LAN0 (Passive PoE in) RESET LANPOERemote Reset Shielded Ethernet Port LAN1 Power LED The Power LED indicates the electricity current situation: green (0~0.8A), red (0.8A~1A). 6 Hardware Connection • Mounting Height 1. Site Consideration Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See Q2 in FAQ for details about how to calculate the minimum mounting height of the devices. line of sight Side View 7 • Orientation Install the CPE devices with their fronts facing the signal receivers. You can orient the devices with the assistance of Google Map, GPS and some landmarks according to the horizontal beamwidth listed below. Horizontal Angleline of sight A shenzhen B line of sight Horizontal Beamwidth ModelsCPE210CPE220CPE510CPE520 Horizontal Beamwidth65°45°45°50° 8 2. Ethernet Cable Preparation 1. Select the adequate type of Ethernet cable. The shielded CAT5e cable with ground wire (refer to the figure below) is prior to the general shielded CAT5e cable during the whole cabling. The former can more effectively protect your devices against ESD attacks under brutal outdoor environment. Shielded CAT5e Cable with Ground Wire Twisted Pair Ground Wire Shielded RJ45 Connector Secondary Cable Shield Cable Shield Sheath 2. Review the routes of connecting the POE Adapter to the CPE and evaluate the Ethernet cable length for all the connections, then prepare adequate Ethernet cable. 9 3. Connection and Installation At the selected site, approximately align the CPE to the direction that you have oriented. Please connect and install the device as shown in the fi gure below. Connect the PoE Adapter to a power outlet with the power cord. Connect the LAN port of the PoE Adapter to a computer, router or switch. Connect the LAN0 (POE IN) port of the CPE to the PoE port of the PoE Adapter. Power over Ethernet up to 60m Slide to replace the cover of the CPE when all connections are fi nished. This device complies with part 15 o f the FCC R ules. O peration is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID:TE7CPE510 MADE IN CHINA IC:8853A-CPE510 Default Settings: IP: 192.168.0.254 Username: admin Password: admin Model: CPE510 Power: 24V 1A 5GHz 300Mbps 13dBi Outdoor CPE 5734 Fasten the CPE with the provided Pole Mounting Straps to a pole or mounting bracket. 10 4. Lightning & ESD Protection Proper grounding is extremely important for outdoor devices. Pharos CPEs provide two methods to protect the devices from damage of lightning and ESD attacks as shown in the fi gure below. Shielded CAT5e Cable with Ground Wire & PoE Adapter with Earth Ground Grounding Terminal and Cable CPE Shielded CAT5e Cable with Ground Wire PoE Adapter with Earth Ground Grounding Terminal Grounding Cable Earth Ground Two Methods: 2 2 1 1 1 1 In most cases, adopting either of the two methods can be adequate, but adopting both of them can off er more eff ective protection. 11 1. Login to PharOS 1. Before accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.x (2≤x≤253) to your computer. We use 192.168.0.10 as an example in the fi gure below. This chapter introduces the login to the Pharos Web Interface and the software confi gurations to implement Point-to-Point application. Software Confi guration

12 2. Open your web browser, type 'http://192.168.0.254' in the address fi eld and press 'Enter'. It is recommended to use the latest version of Google Chrome, Safari or Firefox. 3. The 'Login' page will appear, set the parameters as below. • Username: admin • Password: admin • Region: select according to your country/region • Select 'I agree to these terms of use' • Click 'Login' 4. At the fi rst login, change the 'Password' for safety. For subsequent logins, you only need to enter the username and password that you have set to log in. 13 5. Then you will log in to the PharOS Web Interface and see the Status page, shown as the fi gure below. 14 • Point-to-Point Point-to-Point application is used to build a transparent bridge between two locations which are far from each other. The figure shown below is an example for this application. Refer to the following steps to configure the CPEs. 2. Configuration for Typical Application This section introduces the configurations for the Point-to-Point application. Configure the Access Point 1. Log in to PharOS 2. Go to the Quick Setup page 3. Operation Mode • Select 'Access Point' • Click 'Next' 4. LAN Settings: Click 'Next' 5. Wireless AP Settings • SSID: customize the name for the network as you like • Security: select 'WPA-PSK/WPA2-PSK' • PSK Password: create the password for the network as you like • Distance Setting: enter the distance between the Access Point and the Client. It is recommended to round the number up to the nearest integer • Select the MAXtream option if the Access Point and the Client both are Pharos outdoor CPEs. (Refer to Q4 in FAQ for details about MAXtream) • Click 'Next' 6. Finsh: Click 'Finish' IP camera Access Point LAN: 192.168.0.254 Client LAN: 192.168.0.2 Computer 15 Configure the Client 1. Log in to PharOS 2. Go to the Quick Setup page 3. Operation Mode • Select 'Client' • Click 'Next' 4. LAN Settings • IP Address: 192.168.0.2 (on the same subnet with the Access Point) • Click 'Next' 5. Wireless Client Settings • SSID of Remote AP: click 'Survey', select the SSID of the Access Point, and click 'Connect' • Security: select 'WPA-PSK/WPA2-PSK' • PSK Password: enter the password of the Access Point • Distance Setting: enter the same number with the Access Point • Click 'Next' 6. Finsh: Click 'Finish' 16 Antenna Alignment In order to get the best performance, you can precisely align the direction of the CPE with the assistance of 'Wireless Signal Quality' on STATUS page of the Pharos Web Interface. 24dB 22dB 18dB 22dB 18dB WISP Adjust the direction of the CPE until the device reaches the highest SNR 17 HARDWARE FEATURES Dimensions CPE520/CPE220: 275.83*79*60.3mm CPE510/CPE210: 224.34*79*60.3mm Interface LAN0: 10/100Mbps Ethernet Port(PoE IN) LAN1: 10/100Mbps Ethernet Port GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default Power Supply 24V Passive PoE Adapter Included ESD Protection 1) 15kV Lightning Protection 1) 6kV Operating Temperature -30 °C ~60 °C (-22°F~158°F) Operating Humidity 5% ~ 95 % Certification CE, FCC, RoHS, IPX5 WIRELESS FEATURES Models CPE210 CPE220 CPE510 CPE520 Antenna Gain 9dBi 12dBi 13dBi 16dBi Horizontal Beamwidth/ Elevation Beamwidth 2) 65°/ 45° 45°/ 30° 45°/ 33 ° 50°/ 20 ° Maximum Transmit Power 3) 27dBm 30dBma 27dBm 30dBm Operating Frequency 2.4- 2.4835GHz 2.4- 2.4835GHz 5.15- 5.85GHz 5.15- 5.85GHz 802.11 Standards 11b/g/n 11b/g/n 11a/n 11a/n Specifications 1) Estimation is based on copper grounding cable and shielded CAT5e cable with ESD drain wire. 2) Beamwidth values may vary throughout operating frequency. 3) Maximum transmit power and operating frequency may vary in different countries or regions. Note 1 Frequently Asked Questions (FAQ) Q1. How to restore the CPE to its factory default settings? With the CPE powered on, press and hold the 'RESET' button of the CPE or the 'Remote Reset' button of the Passive PoE Adapter for about 8 seconds until the Wireless Signal Strength LEDs flash. RESET Remote Reset Pharos CPE: Passive PoE Adapter: 1 Q2. How to calculate the minimum mounting height of the devices? In order to maximize the received signal strength of the devices, installers need to minimize the effect of the out-of-phase signals, which is caused by obstacles in the path between the transmitter and the receiver. Fresnel Zone is a usual method to calculate this path, as shown in the formula and the figure below. where, r = Fresnel zone radius in meters c = 3x10 8 m/s, speed of light f = operating frequency of the devices in Hz d1 & d2 = the distances between the point and the devices in meters h = the height of obstacle at this point H h+r * (1 40%) (H is the height of the CPE) For example, assume d1 is 2km, d2 is 8km, and f is 2.4GHz, then r would be 14.142m. Considering a toleration of 40%, allowable radius would be 8.485m. Assume h is 10m, then the result of the minimum mounting height based on this point would be 18.485m. Similarly, calculate the results based on all the points where there are obstacles, and the maximum value would be the final result. For more information, please refer to http://en.wikipedia.org/wiki/Fresnel_zone f c dd dd r⋅ + × = 21 21 d2 r d1 20 Q3. How can I use Spectrum Analysis to fi nd the appropriate channel for the devices? 1. Log in to PharOS, on the 'WIRELESS' page, you can fi nd the 'Spectrum Analysis' button as shown in the fi gure below. Click the button. 2. The following window will pop up. Click 'Yes' and you will then get into the Spectrum Analysis page. 3. Select the 'Frequency Range' and click the 'Start' button, the PharOS will begin to analyze the power of the frequency. Watch the curves for a period of time, and then click 'Stop'. Mark the relatively low and continuous part of the average curve, and note the corresponding frequency range. Here we take the fi gure below as an example. into the Spectrum Analysis page. into the Spectrum Analysis page. into the Spectrum Analysis page. 21 4. Close…

Text truncated - open the document above for the full version.

Declaration for no non-US channel operation Date: Aug. 11, 2014 We, TP-LINK TECHNOLOGIES CO., LTD. declare that the device does not support any non-US channel (12, 13) in all the operational mode(s) for the flowing product. Limited to local law of the United States, selecting country code and channel function is locked by operating system. Any trial of such modifications will be rejected. FCC ID: TE7CPE210 Product description: 2.4GHz 300Mbps 9dBi Outdoor CPE If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP‐LINK Technologies Co., Ltd. Tel: 86‐755‐26525554 Fax: 86‐755‐26508930 Web site: WWW.TP‐LINK.COM E‐mail: public@tp‐link.com.cn

Attestation for FCC Declaration of Conformity FCC ID: TE7CPE210 Date: 2014-05-30 Please be notified that we, the undersigned, TP-LINK TECHNOLOGIES CO., LTD declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC is EM-F140132, with is issued by an accredited lab, Audix Technology Corporation, EMC Department located at No. 53-11, Tin-Fu Tsun, Lin-Kou , Taipei Hsien , Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP‐LINK Technologies Co., Ltd. Tel: 86‐755‐26525554 Fax: 86‐755‐26508930 Web site: WWW.TP‐LINK.COM E‐mail: public@tp‐link.com.cn

AGENCY AUTHORIZATION LETTER FCC ID: TE7CPE210 Date: May 30, 2014 To whom it may concern: We, the undersigned, hereby authorize Audix Technology (Shenzhen) Co., Ltd (No. 6, Ke Feng Rd., 52 Block, Shenzhen Science & Industrial Park,Nantou,Shenzhen, Guangdong, China) to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by Audix within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months from original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, Name of authorized signer: Yo ngq u an Wang Title of authorized signer: Product Dept. Manager Company Name: TP‐LINK Technologies Co., Ltd. Tel: 86‐755‐26525554 Fax: 86‐755‐26508930 Web site: WWW.TP‐LINK.COM E‐mail: public@tp‐link.com.cn

Date: May 30, 2014 Federal Communications Commission Authorization and Evaluation Division FCC ID: TE7CPE210 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this application as outlined below: 1. Block diagram 2. Schematics 3. Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might to harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP‐LINK Technologies Co., Ltd. Tel: 86‐755‐26525554 Fax: 86‐755‐26508930 Web site: WWW.TP‐LINK.COM E‐mail: public@tp‐link.com.cn

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-1 14. PHOTOS OF THE EUT Figure 1 General Appearance of the EUT Figure 2 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-2 Figure 3 General Appearance of the EUT Figure 4 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-3 Figure 5 General Appearance of the EUT Figure 6 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-4 Figure 7 General Appearance of the EUT Figure 8 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-5 Figure 9 General Appearance of the EUT Figure 10 General Appearance of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-6 Figure 11 General Appearance of the EUT Figure 12 General Appearance of the EUT

颜 色 名 称 版 本 材 质 模 具 机型版本号 logo 底色 文字 其它 结构工程师 硬件工程师 产品工程师 平面负责人 记 录 与上一版的区别 完成日期 设 计 C B A 12 C 345678 B E D D A 9 料号： 12345 E 6789 CPE210(UN)_1.0_壳体丝印 A1 灯塔-224 CPE210(UN)_1.0 程 成 2013-10-09 PANTONE Cool Gray 6C TP-LINK LOGO左右居中 菲林图（文字转曲线）文字未转曲 尺寸：34.412*4.385mm 颜色：PANTONE Cool Gray 6C 颜色：PANTONE Cool Gray 6C 224.23 22.2 42.86 79 224.23 79 79 224.23 9.27 49.65 58.012 14.56 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID:TE7CPE210 MADE IN CHINA IC:8853A-CPE210 Default Settings: IP: 192.168.0.254 Username: admin Password: admin Model: CPE210 Power: 24V 1A 2.4GHz 300Mbps 9dBi Outdoor CPE 5734 79 224.23

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-7 Figure 13 Inside of the EUT Figure 14 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-8 Figure 15 Inside of the EUT Figure 16 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-9 Figure 17 Inside of the EUT Figure 18 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-10 Figure 19 Inside of the EUT Figure 20 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-11 Figure 21 Inside of the EUT Figure 22 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-12 Figure 23 Inside of the EUT Figure 24 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-13 Figure 25 Inside of the EUT Figure 26 Inside of the EUT R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-14 Figure 27 Power Adapter Figure 28 Power Adapter R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-15 Figure 29 Power Adapter Figure 30 Power Adapter R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-16 Figure 31 Power Adapter Figure 32 Power Adapter R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 14-17 Figure 33 Power Adapter Figure 34 Power Adapter

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 10-1 10. MPE ESTIMATION 10.1.Limit for General Population/ Uncontrolled Exposures Frequency Power density (mW/ cm 2 ) Averaging time(minutes) 300MHz----1.5GHz F/1500 30 1.5GHz---100GHz 1.0 30 Frequency(MHz) Power density (mW/ cm 2 ) Averaging time(minutes) 2412 1 30 2437 1 30 2462 1 30 Note: F= Frequency in MHz Estimation Result 5MHz EUT: 2.4GHz 300Mbps 9dBi Outdoor CPE M/N: CPE210 Test date: 2014-04-01 Pressure: 101.31.0 kpa Humidity: 52.33.0% Tested by: Leo-Li Test site: RF site Temperature: 21.90.6 Cable loss: 1 dB Attenuator loss: 20 dB Antenna Gain: 9dBi Test Mode CH Frequency MHz Peak Output Power (dBm) Output Power (mW) Antenna Gain (dBi) Antenna Gain (Linear) MPE CH1 2412 27.36 544.50 9 7.94 0.8609 CH6 2437 27.43 553.35 9 7.94 0.8749 11b CH11 2462 26.91 490.91 9 7.94 0.7762 CH1 2412 27.22 527.23 9 7.94 0.8336 CH6 2437 27.20 524.81 9 7.94 0.8298 11g CH11 2462 27.40 549.54 9 7.94 0.8689 CH1 2412 27.60 575.44 9 7.94 0.9098 CH6 2437 27.46 557.19 9 7.94 0.8809 11n HT20 CH11 2462 27.29 535.80 9 7.94 0.8471 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 10-2 10MHz EUT: 2.4GHz 300Mbps 9dBi Outdoor CPE M/N: CPE210 Test date: 2014-04-01 Pressure: 101.31.0 kpa Humidity: 52.63.0% Tested by: Leo-Li Test site: RF site Temperature: 22.40.6 Cable loss: 1 dB Attenuator loss: 20 dB Antenna Gain: 9dBi Test Mode CH Frequency MHz Peak Output Power (dBm) Output Power (mW) Antenna Gain (dBi) Antenna Gain (Linear) MPE CH1 2412 27.31 538.27 9 7.94 0.8510 CH6 2437 27.68 586.14 9 7.94 0.9267 11b CH11 2462 27.55 568.85 9 7.94 0.8994 CH1 2412 27.24 529.66 9 7.94 0.8374 CH6 2437 27.39 548.28 9 7.94 0.8669 11g CH11 2462 27.30 537.03 9 7.94 0.8491 CH1 2412 27.43 553.35 9 7.94 0.8749 CH6 2437 27.49 561.05 9 7.94 0.8871 11n HT20 CH11 2462 27.47 558.47 9 7.94 0.8830 20MHz EUT: 2.4GHz 300Mbps 9dBi Outdoor CPE M/N: CPE210 Test date: 2014-3-25 Pressure: 101.31.0kpa Humidity: 52.23.0% Tested by: Leo-Li Test site: RF site Temperature: 21.40.6 Cable loss: 1 dB Attenuator loss: 20 dB Antenna Gain: 9dBi Test Mode CH Frequency MHz Peak Output Power (dBm) Output Power (mW) Antenna Gain (dBi) Antenna Gain (Linear) MPE CH1 2412 27.75 595.66 9 7.94 0.9418 CH6 2437 27.50 562.34 9 7.94 0.8891 11b CH11 2462 27.33 540.75 9 7.94 0.8550 CH1 2412 27.93 620.87 9 7.94 0.9816 CH6 2437 27.79 601.17 9 7.94 0.9505 11g CH11 2462 27.91 618.02 9 7.94 0.9771 CH1 2412 25.70 371.54 9 7.94 0.5874 CH6 2437 27.80 602.56 9 7.94 0.9527 11n HT20 CH11 2462 25.61 363.92 9 7.94 0.5754 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 10-3 40MHz EUT: 2.4GHz 300Mbps 9dBi Outdoor CPE M/N: CPE210 Test date: 2014-3-25 Pressure: 101.31.0 kpa Humidity: 52.23.0% Tested by: Leo-Li Test site: RF site Temperature:21.40.6 Cable loss: 1 dB Attenuator loss: 20 dB Antenna Gain: 9dBi Test Mode CH Frequency MHz Peak Output Power (dBm) Output Power (mW) Antenna Gain (dBi) Antenna Gain (Linear) MPE CH1 2422 25.29 338.06 9 7.94 0.5345 CH4 2437 27.95 623.73 9 7.94 0.9862 11n HT40 CH7 2452 24.41 276.06 9 7.94 0.4365

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of TP-LINK TECHNOLOGIES CO., LTD. 2.4GHz 300Mbps 9dBi Outdoor CPE Model No.: CPE210 FCC ID: TE7CPE210 Prepared for : TP-LINK TECHNOLOGIES CO., LTD. Building 24(floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China Prepared By : Audix Technology (Shenzhen) Co., Ltd. No. 6, Ke Feng Rd., 52 Block, Shenzhen Science & Industrial Park, Nantou, Shenzhen, Guangdong, China Tel: (0755) 26639496 Report Number ACS-F14082 Date of Test Mar.25~May.10, 2014 Date of Report Jun.19, 2014 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 TABLE OF CONTENTS Description Page 1. SUMMARY OF STANDARDS AND RESULTS ......................................................... 1-1 1.1. Description of Standards and Results ...................................................................................1-1 2. GENERAL INFORMATION ......................................................................................... 2-1 2.1. Description of Device (EUT) ...............................................................................................2-1 2.2. Test Information ...................................................................................................................2-2 2.3. Tested Supporting System Details........................................................................................2-2 2.4. Block Diagram of Test Setup ...............................................................................................2-2 2.5. Test Facility ..........................................................................................................................2-3 2.6. Measurement Uncertainty (95% confidence levels, k=2).....................................................2-3 3. POWER LINE CONDUCTED EMISSION TEST....................................................... 3-1 3.1. Test Equipments ...................................................................................................................3-1 3.2. Block Diagram of Test Setup ...............................................................................................3-1 3.3. Power Line Conducted Emission Test Limits ......................................................................3-1 3.4. Configuration of EUT on Test..............................................................................................3-1 3.5. Operating Condition of EUT ................................................................................................3-2 3.6. Test Procedure ......................................................................................................................3-2 3.7. Power Line Conducted Emission Test Results .....................................................................3-2 4. RADIATED EMISSION TEST ...................................................................................... 4-1 4.1. Test Equipment.....................................................................................................................4-1 4.2. Block Diagram of Test Setup ...............................................................................................4-2 4.3. Radiated Emission Limit ......................................................................................................4-3 4.4. EUT Configuration on Test ..................................................................................................4-3 4.5. Operating Condition of EUT ................................................................................................4-3 4.6. Test Procedure ......................................................................................................................4-4 4.7. Radiated Emission Test Results ...........................................................................................4-4 5. CONDUCTED SPURIOUS EMISSIONS ..................................................................... 5-1 5.1. Test Equipment.....................................................................................................................5-1 5.2. Limit .....................................................................................................................................5-1 5.3. Test Procedure ......................................................................................................................5-1 5.4. Test result .............................................................................................................................5-1 6. BAND EDGE COMPLIANCE TEST............................................................................ 6-1 6.1. Test Equipment.....................................................................................................................6-1 6.2. Limit .....................................................................................................................................6-1 6.3. Test Produce .........................................................................................................................6-1 6.4. Test Results ..........................................................................................................................6-1 7. 6dB Bandwidth Test ........................................................................................................ 7-1 7.1. Test Equipment.....................................................................................................................7-1 7.2. Limit .....................................................................................................................................7-1 7.3. Test Procedure ......................................................................................................................7-1 7.4. Te…

Text truncated - open the document above for the full version.

R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-30 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-31 Test CH6: 2437MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-32 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-33 Test CH11: 2462MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-34 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-35 10MHz Antenna: J2 Test Mode: IEEE 802.11b Test CH1: 2412MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-36 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-37 Test CH6: 2437MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-38 Test CH11: 2462MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-39 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-40 Test Mode: IEEE 802.11g Test CH1: 2412MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-41 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-42 Test CH6: 2437MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-43 R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-44 Test CH11: 2462MHz R AUDIX Technology (Shenzhen) Co., Ltd. FCC ID:TE7CPE210 page Audix Technology (Shenzhen) Co., Ltd. Report No. ACS-F14082 5-45…

Text truncated - open the document above for the full version.