TE7EAP110300Mbps Wireless N Access Point

User Guide Wireless N Access Point EAP110/EAP120/EAP220 REV1.0.0 1910011184 EAP110 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1） This device may not cause harmful interference. 2） This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d’interférences et (2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Korea Warning Statements 당해 무선설비는 운용중 전파혼신 가능성이 있음. NCC Notice & BSMI Notice 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時， 應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電 信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 減少電磁波影響，請妥適使用。 安全諮詢及注意事項 ●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮，請勿將水或其他液體潑灑到本產品上。 ●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用 者會被要求採取某些適當的對策。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information  When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.  Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.  Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SK TR UA US EAP120 and EAP220 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. A…

Text truncated - open the document above for the full version.

TP-LinkTechnologiesCo.,Ltd. Building24(floors1,3,4,5)and28(floors1-4), CentralScienceandTechnologyPark,Nanshan,Shenzhen,China AttestationforFCCDeclarationofConformity FCCID:TE7EAP110Date:2015-02-03 Pleasebenotifiedthatwe,theundersigned,TP-LINKTECHNOLOGIESCO., LTDdeclarethattheproductbearstheaboveFCCIDisalsocomplyingwith therequirementsofFCCDoC.ThetestreportnumberforFCCDoCis FD141229C15,withisissuedbyanaccreditedlab,BureauVeritasConsumer ProductsServices(H.K.)Ltd.,TaoyuanBranch(BVCPSTaoyuan)ofTaiwan. Whichhasbeenaccreditedinaccordancetoalloftherequirementsof47CFR 2.948(d)and(e)oftheFCCrulesandKDB349827. Sincerely, Nameofauthorizedsigner:YongquanWang Titleofauthorizedsigner:ProductDept.Manager CompanyName:TP-LINKTechnologiesCo.,Ltd. Tel:86-755-26525554 Fax:86-755-26508930 Website:WWW.TP-LINK.COM E-mail:[email protected]

TEL:86-755-26525554FAX:86-755-26508930 Date:2015-02-03 FCCID:TE7EAP110 A U T H O R I Z A T I O NL E T T E R Towhomitmayconcern: We,theundersigned,herebyauthorizeAndreaHsia(SeniorSpecialist)ofBureau VeritasConsumerProductsServices(H.K.)Ltd.,TaoyuanBranch(BVCPSTaoyuan)of TaiwantoactonourbehalfinallmannersrelatingtoFCCapplicationforequipment authorization,includingsigningofalldocumentsrelatingtothesematters.Anyandall actscarriedoutbyAndreaHsia(SeniorSpecialist)ofBVCPSTaoyuanonourbehalfshall havethesameeffectasactsofourown. Ifyouhaveanyquestionsregardingtheauthorization,pleasedon’thesitatetocontactus. Sincerelyyours, ----------------------------------- Name:YongquanWang TP-LinkTechnologiesCo.,Ltd. Tel.:+86-755-26525554 Fax.:+86-755-26508930 E-mail:[email protected]

TP-LinkTechnologiesCo.,Ltd. Building24(floors1,3,4,5)and28(floors1-4), CentralScienceandTechnologyPark,Nanshan,Shenzhen,China Date:2015-02-03 FCCID:TE7EAP110 Totheattentionof FederalCommunicationsCommission AuthorizationandEvaluationDivision ConfidentialityRequest PursuanttoSections0.457and0.459oftheCommission’sRules,theApplicantherebyrequests confidentialtreatmentofinformationaccompanyingthisApplicationasoutlinedbelow: Schematics BlockDiagram OperationalDescription Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleasedto thepublic.ThepublicdisclosureofthesemattersmightbeharmfultotheApplicantandprovide unjustifiedbenefitstoitscompetitors. TheApplicantunderstandsthatpursuanttoRule0.457,disclosureofthisApplicationandall accompanyingdocumentationwillnotbemadebeforethedateoftheGrantforthisapplication. Sincerelyyours, Name:YongquanWang TP-LinkTechnologiesCo.,Ltd. Tel.:+86-755-26525554 Fax.:+86-755-26508930 E-mail:[email protected]

TP-LinkTechnologiesCo.,Ltd. Building24(floors1,3,4,5)and28(floors1-4), CentralScienceandTechnologyPark,Nanshan,Shenzhen,China Declarationfornonon-USchanneloperation February3,2015 We,TP-LINKTECHNOLOGIESCO.,LTDdeclarethatthedevicedoesnotsupportchannel12~13in 2.4GHzbandandanynon-USchannelsinalltheoperationalmode(s)forthefollowingproduct. FCCID:TE7EAP110 Ifyoushouldhaveanyquestion(s)regardingthisdeclaration,pleasedon’thesitatetocontactus.Thank you! Nameofauthorizedsigner:YongquanWang Titleofauthorizedsigner:ProductDept.Manager CompanyName:TP-LINKTechnologiesCo.,Ltd. Tel:86-755-26525554 Fax:86-755-26508930 Website:WWW.TP-LINK.COM E-mail:[email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

Label location

Page 4 Page 5 Page 6 Page 7

Report No.: SA141229C15 1 of 7 Report Format Version 5.0.1 EXPOSURE REPORT REPORT NO.: SA141229C15 MODEL NO.: EAP110 FCC ID: TE7EAP110 IC: 8853A-EAP110 RECEIVED: Dec. 29, 2014 TESTED: Jan. 06 ~ Jan. 19, 2015 ISSUED: Jan. 20, 2015 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. Report No.: SA141229C15 2 of 7 Report Format Version 5.0.1 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE ....................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ................................. 5 2.2 MPE CALCULATION FORMULA ............................................................................. 6 2.3 CLASSIFICATION .................................................................................................... 6 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .......................... 7 Report No.: SA141229C15 3 of 7 Report Format Version 5.0.1 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA141229C15 Original release Jan. 20, 2015 Report No.: SA141229C15 4 of 7 Report Format Version 5.0.1 1. CERTIFICATION PRODUCT: 300Mbps Wireless N Access Point MODEL NO.: EAP110 BRAND: TP-LINK APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED: Jan. 06 ~ Jan. 19, 2015 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) KDB 447498 D03 IEEE C95.1 RSS-102 Issue 4 (2010-03) The above equipment (model: EAP110) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY :, DATE :Jan. 20, 2015 Celine Chou / Specialist APPROVED BY : , DATE :Jan. 20, 2015 Ken Liu / Senior Manager Report No.: SA141229C15 5 of 7 Report Format Version 5.0.1 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) For FCC Part 2 (Section 2.1091) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz For RSS-102 Issue 4 (2010-03) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (W/m 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/150 6 1500-100,000 ... ... 10 6 F = Frequency in MHz Report No.: SA141229C15 6 of 7 Report Format Version 5.0.1 2.2 MPE CALCULATION FORMULA For FCC Part 2 (Section 2.1091) Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm For RSS-102 Issue 4 (2010-03) Pd = (Pout*G) / (4*pi*r2) where Pd = power density in W/m 2 Pout = output power to antenna in W G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in meter 2.3 CLASSIFICATION For FCC Part 2 (Section 2.1091) The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. For RSS-102 Issue 4 (2010-03) The antenna of this product, under normal use condition, is at least 0.20m away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA141229C15 7 of 7 Report Format Version 5.0.1 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For FCC Part 2 (Section 2.1091) FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412 ~ 2462 26.94 6.01 20 0.392 1 NOTE: Directional gain = 3dBi + 10log(2) = 6.01dBi For RSS-102 Issue 4 (2010-03) FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (m) POWER DENSITY (W/m 2 ) LIMIT (W/m 2 ) 241…

Text truncated - open the document above for the full version.

Report No.: RF141229C15 1 of 60 Report Format Version 5.2.1 FCC TEST REPORT REPORT NO.: RF141229C15 MODEL NO.: EAP110 FCC ID: TE7EAP110 IC: 8853A-EAP110 RECEIVED: Dec. 29, 2014 TESTED: Jan. 06 ~ Jan. 19, 2015 ISSUED: Jan. 20, 2015 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF141229C15 2 of 60 Report Format Version 5.2.1 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 4 1. CERTIFICATION ............................................................................................................ 5 2. SUMMARY OF TEST RESULTS .................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY .................................................................................. 6 3. GENERAL INFORMATION ............................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................... 7 3.2 DESCRIPTION OF TEST MODES ................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................. 9 3.3 DUTY CYCLE OF TEST SIGNAL .................................................................................. 11 3.4 DESCRIPTION OF SUPPORT UNITS ......................................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................................. 13 4. TEST TYPES AND RESULTS ...................................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ....................................... 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .................... 14 4.1.2 TEST INSTRUMENTS .................................................................................................. 15 4.1.3 TEST PROCEDURES .................................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................ 16 4.1.5 TEST SETUP ................................................................................................................ 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................. 18 4.1.7 TEST RESULTS ........................................................................................................... 19 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................... 32 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................................. 32 4.2.2 TEST INSTRUMENTS .................................................................................................. 32 4.2.3 TEST PROCEDURES .................................................................................................. 33 4.2.4 DEVIATION FROM TEST STANDARD ........................................................................ 33 4.2.5 TEST SETUP ................................................................................................................ 33 4.2.6 EUT OPERATING CONDITIONS ................................................................................. 33 4.2.7 TEST RESULTS ........................................................................................................... 34 4.3 6dB BANDWIDTH MEASUREMENT ............................................................................ 36 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ......................................................... 36 4.3.2 TEST SETUP ................................................................................................................ 36 4.3.3 TEST INSTRUMENTS .................................................................................................. 36 4.3.4 TEST PROCEDURE ...................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST (ABOVE 1GHz) 3 RADIATED EMISSION TEST (BELOW 1GHz)