TE7M5350V13G Mobile Wi-Fi

M5350 3G Mobile Wi-Fi REV 1.0.0 1910010751 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Con nect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cau se undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. In SAR test, 1cm form the body is the distance to test the human exposure to radio frequency fields. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device has been designed to operate with an internal antenna, please do not change an antenna. This product has been tested for SAR item to insure the human exposure to radio frequency fields under a safe level. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS st andard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired opera tion of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1)cet appareil ne doit pa s provoquer d’interférences et (2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This de vice complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. NCC Notice & BSMI Notice 注意！ 依據 低功率電波輻射性電機管理辦法 Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou quele dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. 第十二條 經型式認證合格之低功率射頻電機，費經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立 即停用，并改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率 射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 安全諮詢及注意事項 ● 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ● 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ● 注意防潮，請勿將水或其他液體潑灑到本產品上。  ● 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ● 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ● 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information  When product has power button, the power button is one of the way to shut off the product; When there is no power button, the only way to completely …

Text truncated - open the document above for the full version.

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Declaration for no non‐US channel operation November 20, 2013 We, TP‐Link Technologies Co., Ltd., declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: TE7M5350V1 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1- 4) , Central Science and Technology Park, Na nshan, Shenzhen, China Date: 2013-06-20 FCC ID: TE7M5350V1 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0. 457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0. 457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Yongquan Wang TP-Link Technologies Co., Ltd. Tel.: +86-755-26502509 Fax.: +86-755-26508930 E-mail: [email protected] BOM Turn-up Procedure

Attestation for FCC Declaration of Conformity FCC ID: TE7M5350V1 Date: 2013-6-25 Please be notified that we, the undersigned, TP-LINK TECHNOLOGIES CO., LTD declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC is FD130412C16, with is issued by an accredited lab, Bureau Veritas Consumer Products Services(H.K.) Ltd., Taoyuan Branch located at No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP-LINK Technologies Co., Ltd. Tel: 86-755-26525554 Fax: 86-755-26508930 Web site: WWW.TP-LINK.COM E-mail: [email protected]

Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China Declaration letter Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Ddeclaration letter for label requirement Date: 2013-06-28 FCC ID: TE7M5350V1 The label is permanent affixed in the battery compartment, and the EUT will be selling to market without the battery installed. The users can see the label during the battery installation process. The battery cover can be opened without any special tools. Please don’t hesitate to contact us, if you have any question(s). Thank you! Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP-LINK Technologies Co., Ltd. Tel: 86-755-26525554 Fax: 86-755-26508930 Web site: WWW.TP-LINK.COM E-mail: [email protected]

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Date: 2013‐06‐20 AUTHORIZATION LETTER To whom it may concern: We, the undersigned TP‐Link Technologies Co., Ltd., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Battery 1 Page 3 Page 4 Battery 2 Page 5 Page 6

Label location

C B A 12 C 345678 B E D D A 9 料号： 12345 与上一版的区别 E 6789 颜 色 名 称 版 本 材 质 模 具 机型版本号 logo 底色 文字 其它 结构工程师 硬件工程师 产品工程师 平面负责人 记 录 审 核 完成日期 设 计 M5350(UN)1.0 产品规格标贴 A1 80g艾利铜版纸+雾膜 M5350(UN)1.0 高文雯 2012-12-14 黑色 白色 黑色 K=50% 37.5*30mm，R=1.5，公差范围±0.2mm 文字转曲1.5倍放大效果图 序列号标贴由工厂使用料号为7210500097尺寸是23*5mm的空白标贴打印并贴上，条码码制为code 128， MAC地址标贴和IMEI标贴由工厂直接打印，字体为Arial，编码规则同我司，此处为示意 MAC/IMEI条码工厂直接打印， S/N条码打印在空白标贴上并粘贴 码制：Code 128 条码字体：Arial Regular 字号：4pt 注：此处条码为示意 型號: M5350 電源: 5V 1A 默認設置: IP: 192.168.0.1 用戶名: admin 密碼: admin Made in China 3G/3.75G移動式WiFi分享器 FCC ID:TE7M5350V1 IC:8853A-M5350 S/N MAC 2012120701 001478E48EB6 IMEI 1234567890

Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16

FCC SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 26 Report No. : SA130412C16C, Reference No.: 130918C15 Issued Date : Nov. 20, 2013 Revision : R01 FCC SAR Test Report Report No. : SA130412C16C Applicant : TP-LINK TECHNOLOGIES CO., LTD. Address : Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd., Nanshan, Shenzhen, China Product : 3G Mobile Wi-Fi FCC ID : TE7M5350V1 Brand : TP-LINK Model No. : M5350 Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1991 / IEEE 1528:2003 FCC OET Bulletin 65 Supplement C (Edition 01-01) KDB 248227 D01 v01r02 / KDB 447498 D01 v05 / KDB 941225 D01 v02 KDB 941225 D02 v02r01 / KDB 941225 D03 v01 / KDB 941225 D06 v01 Date of Testing : Jun. 03, 2013 ~ Sep. 26, 2013 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch - Taiwan HwaYa Lab, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Evonne Liu / Specialist Approved By : Roy Wu / Manager This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. FCC SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 26 Report No. : SA130412C16C, Reference No.: 130918C15 Issued Date : Nov. 20, 2013 Revision : R01 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ................................................................................................................ 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 14 3.4 SAR Measurement Procedure ................................................................................................................................... 15 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 15 3.4.2 Volume Scan Procedure................................................................................................................................... 15 3.4.3 Power Drift Monitoring ...................................................................................................................................... 16 3.4.4 Spatial Peak SAR…

Text truncated - open the document above for the full version.

Report No.: RF130412C16 1 of 47 Report Format Version 5.2.0 FCC TEST REPORT REPORT NO.: RF130412C16 MODEL NO.: M5350 FCC ID: TE7M5350V1 RECEIVED: Apr. 12, 2013 TESTED: Apr. 23 ~ May 03, 2013 ISSUED: May 08, 2013 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130412C16 2 of 47 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 4 1. CERTIFICATION ..................................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................................... 6 3. GENERAL INFORMATION ..................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ....................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ......................................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................................... 9 3.3 DESCRIPTION OF SUPPORT UNITS ................................................................................. 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................................. 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ...................................................... 12 4. TEST TYPES AND RESULTS .............................................................................................. 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ............................................... 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ............................ 13 4.1.2 TEST INSTRUMENTS .......................................................................................................... 14 4.1.3 TEST PROCEDURES ........................................................................................................... 15 4.1.4 DEVIATION FROM TEST STANDARD ................................................................................. 15 4.1.5 TEST SETUP ........................................................................................................................ 16 4.1.6 EUT OPERATING CONDITIONS ......................................................................................... 16 4.1.7 TEST RESULT ...................................................................................................................... 17 4.2 CONDUCTED EMISSION MEASUREMENT ....................................................................... 28 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ..................................................... 28 4.2.2 TEST INSTRUMENTS .......................................................................................................... 28 4.2.3 TEST PROCEDURES ........................................................................................................... 29 4.2.4 DEVIATION FROM TEST STANDARD ................................................................................. 29 4.2.5 TEST SETUP ........................................................................................................................ 29 4.2.6 EUT OPERATING CONDITIONS ......................................................................................... 29 4.2.7 TEST RESULTS .................................................................................................................... 30 4.3 6dB BANDWIDTH MEASUREMENT .................................................................................... 32 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................................. 32 4.3.2 TEST SETUP ........................................................................................................................ 32 4.3.3 TEST INSTRUMENTS .....................................…

Text truncated - open the document above for the full version.

FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA130412C16C, Reference No.: 130918C15 Revision : R01 <Photographs of EUT> EUT – Front View EUT – Rear View Battery 1 – Front View Battery 1 – Rear View Battery 2 – Front View Battery 2 – Rear View FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA130412C16C, Reference No.: 130918C15 Revision : R01 <Antenna Location> Antenna To Top Side (mm) To Bottom (mm) To Left Side (mm) To Right Side (mm) WWAN 76.5 0 0 0 WLAN 0 80.7 0 32 WLAN Ant. WWAN Ant. Top Side Bottom Side Right Side Left Side FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA130412C16C, Reference No.: 130918C15 Revision : R01 <Photographs of SAR Setup for Battery 1> Front Face of EUT with 1.0 cm Gap Rear Face of EUT with 1.0 cm Gap Left Side of EUT with 1.0 cm Gap Right Side of EUT with 1.0 cm Gap Top Side of EUT with 1.0 cm Gap Bottom Side of EUT with 1.0 cm Gap FCC SAR Test Report Report Format Version 5.0.0 Report No. : SA130412C16C, Reference No.: 130918C15 Revision : R01 <Photographs of SAR Setup for Battery 2> Rear Face of EUT with 1.0 cm Gap

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (WLAN) 2 CONDUCTED EMISSION TEST (Part 22) 3 CONDUCTED EMISSION TEST (Part 24) 4 RADIATED EMISSION TEST (WLAN) 5 RADIATED EMISSION TEST (Part 22) 6 RADIATED EMISSION TEST (Part 24)