TE7RE580DAC1900 Wi-Fi Range Extender

1910011262 REV 1.0.0 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright ©2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co- located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 26 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” This device is restricted in indoor environment only. This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Belarus Not implemented Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund on Svalbard. Italy Implemented The public use is subject to general authorisation by the respective service provider. Russian Federation Limited implementation 1. SRD with FHSS modulation 1.1. Maximum 2.5 mW e.i.r.p. 1.2. Maximum 100 mW e.i.r.p. Permitted for use SRD for outdoor applications without restriction on installation height only for purposes of gathering telemetry information for automated monitoring and resources accounting systems. Permitted to use SRD for other purposes for outdoor applications only when the installation height is not exceeding 10 m above the ground surface. 1.3.Maximum 100 mW e.i.r.p. Indoor applications. 2. SRD with DSSS and other than FHSS wideband modulation 2.1. Maximum mean e.i.r.p. density is 2 mW/MHz. Maximum 100 mW e.i.r.p. 2.2. Maximum mean e.i.r.p. density is 20 mW/MHz. Maximum 100 mW e.i.r.p. It is permitted to use SRD for outdoor applications only for purposes of gathering telemetry information for automated monitoring and resources accounting systems or security systems. 2.3. Maximum mean e.i.r.p. density is 10 mW/MHz. Maximum 100 mW e.i.r.p. Indoor applications. Ukraine Limited implementation e.i.r.p. ≤100 mW with built-in antenna with amplification factor up to 6 dBi. ATTENTION: Due to EU law, the country settings must be identical to the country where the device is operating (important due to non-harmonised frequencies in the EU). Restricted to indoor use. This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : l'appareil nedoit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This radio transmitter (IC: 8853A-RE580D / Model: RE580D) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list (Appendix), having a gain greater than the maximum gain in…

Text truncated - open the document above for the full version.

Apr.16,2015 FederalCommunicationsCommission AuthorizationandEvaluationDivision FCCID：TE7RE580D ConfidentialityRequest PursuanttoSections0.457and0.459oftheCommission’sRules,theapplicant herebyrequestsconfidentialtreatmentofinformationappliedthis application asoutlinedbelow: 1.BlockDiagram 2.CircuitDiagram 3.OperationalDescription 4.Softwareoperatingdescription Theabovematerialscontaintradesecretsandproprietaryinformationnot customarily releasedtothepublic.Thepublicdisclosureofthesemattersmightbe harmfultotheapplicantandprovideunjustifiedbenefitstoitscompetitors. TheApplicantunderstandsthatpursuanttoRule0.457,disclosureofthis Applicationandallaccompanyingdocumentationwillnotbemadebeforethe dateoftheGrantforthisapplication Sincerely, Name:YongquanWang TP-LinkTechnologiesCo.,Ltd. Tel.:+86-755-26502509 Fax.:+86-755-26508930 E-mail:[email protected]

Date:2015-10-15 Subject:AdHocModeFunctionDeclaration FCCID:TE7RE580D ToWhomitmayconcern, Thisdeviceisactingasmasterandoperatingon2.4GHzband(Channel1~11)&5GHz(Band1&4) andnotabletoworkonnon-USfrequencies.Pleasecontacttheonesignedbelowortheauthorized agentforthisfiling.Thankyou. Regards, Name:YongquanWang TP-LinkTechnologiesCo.,Ltd. Tel.:+86-755-26502509 Fax.:+86-755-26508930 E-mail:[email protected]

Date:2015/10/16 FederalCommunicationsCommission 7435OaklandMillsRoad ColumbiaMD21046 PHOENIXTESTLAB ProductCertificationDepartment Konigswinkel10,D-32825Blomberg,Germany Towhomitmayconcern: I,theundersigned,herebyauthorizeAndreaHsiaSpecialistofBureauVeritasConsumerProducts Services(H.K.)Ltd.,TaoyuanBranch(BVCPSTaoyuan)andhereafterreferredtoasBVCPS Taoyuan,toactonourbehalfinallmannersrelatingtoapplicationforequipmentauthorization, includingsigningofalldocumentsrelatingtothesematters.Anyandallactscarriedoutby AndreaHsiaSpecialistofBureauVeritasConsumerProductsServices(H.K.)Ltd.,Taoyuan Branch(BVCPSTaoyuan)onourbehalfshallhavethesameeffectasactsofourown. I,theundersigned,herebycertifythatwearenotsubjecttoadenialoffederalbenefits,that includesFCCbenefits,pursuanttoSection5301oftheAnti-DrugAbuseActof1988,21U.S.C. 853(a). InauthorizingBVCPSTaoyuanasouragent,westillrecognizethatweareresponsibleto: a)complywiththerelevantprovisionsofthecertificationprogram; b)makeallnecessaryarrangementsfortheconductoftheevaluation,including provisionforexaminingdocumentationandaccesstoallareas,records(including internalauditreports)andpersonnelforthepurposesofevaluation(e.g.testing, inspection,assessment,surveillance,reassessment)andresolutionofcomplaints; c)makeclaimsregardingcertificationonlyinrespectofthescopeforwhich certificationhasbeengranted; d)donotuseourproductcertificationinsuchamannerastobringtheCertification Divisionintodisreputeandnotmakeanystatementregardingourproduct certificationwhichtheCertificationDivisionmayconsidermisleadingor unauthorized; e)uponsuspensionorcancellationofcertification,discontinueuseofalladvertising matterthatcontainsanyreferencetheretoandreturnanycertificationdocuments asrequiredbytheCertificationDivision; f)usecertificationonlytoindicatetheproductsarecertifiedasbeinginconformity withspecifiedstandards; g)endeavortoensurethatnocertificateorreportnoranypartthereofisusedina misleadingmanner; h)ensurethatanyreferencetoourproductcertificationincommunicationmediasuchas documents,brochuresoradvertising,complieswiththerequirementsofthe CertificationDivision; i)keeparecordofallcomplaintsmadeknowntotheusrelatingtotheproduct’s compliancewithrequirementsoftherelevantstandardandtomaketheserecords availabletotheCertificationDivisionwhenrequested; j)takeappropriateactionwithrespecttosuchcomplaintsandanydeficienciesfoundin productsorservicesthataffectcompliancewiththerequirementsforcertification; k)documenttheactionstaken. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours, Name:YongquanWang TP-LinkTechnologiesCo.,Ltd. Tel.:+86-755-26502509 Fax.:+86-755-26508930 E-mail:[email protected] REMARK: 1.Thisauthorizationletterwillbesentalongwithyourapplicationwhenfilingwiththe CertificationDivision. 2.Pleasefollowtheformatandtypeitoncompanyletterheadandsendoriginaltous. 3.AuthorizedsignaturemustbeinagreementwithgranteecodecontactinFCCdatabase.

Label location

Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12

Report No.: SA150408C04 R1 Page No. 1 / 6 Report Format Version: 6.1.1 Cancels and replaces the report No.: SA150408C04 dated Oct. 22, 2015 RF Exposure Report Report No.: SA150408C04 R1 FCC ID: TE7RE580D Test Model: RE580D Received Date: Apr. 08, 2015 Test Date: Aug. 18 to 21, 2015 Issued Date: Oct. 28, 2015 Applicant: TP-LINK TECHNOLOGIES CO., LTD. Address: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA150408C04 R1 Page No. 2 / 6 Report Format Version: 6.1.1 Cancels and replaces the report No.: SA150408C04 dated Oct. 22, 2015 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits For Maximum Permissible Exposure (MPE) ............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Antenna Gain ......................................................................................................................................... 5 4 Calculation Result Of Maximum Conducted Power .......................................................................... 6 Report No.: SA150408C04 R1 Page No. 3 / 6 Report Format Version: 6.1.1 Cancels and replaces the report No.: SA150408C04 dated Oct. 22, 2015 Release Control Record Issue No. Description Date Issued SA150408C04 Original release. Oct. 22, 2015 SA150408C04 R1 Revised FCC ID. Oct. 28, 2015 Report No.: SA150408C04 R1 Page No. 5 / 6 Report Format Version: 6.1.1 Cancels and replaces the report No.: SA150408C04 dated Oct. 22, 2015 2 RF Exposure 2.1 Limits For Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 26cm away from the body of the user. So, this device is classified as Mobile Device. 3 Antenna Gain Transmitter Circuit Brand Model Antenna Gain (dBi) Frequency range (GHz to GHz) Antenna Type Connecter Type Chain (0) NA NA 1.59 2.4-2.4835 Dipole RP-SMA-F 1.03 5.15-5.25 1.43 5.725-5.850 Chain (1) NA NA 1.59 2.4-2.4835 Dipole RP-SMA-F 1.03 5.15-5.25 1.43 5.725-5.850 Chain (2) NA NA 1.59 2.4-2.4835 Dipole RP-SMA-F 1.03 5.15-5.25 1.43 5.725-5.850 Report No.: SA150408C04 R1 Page No. 6 / 6 Report Format Version: 6.1.1 Cancels and replaces the report No.: SA150408C04 dated Oct. 22, 2015 4 Calculation Result Of Maximum Conducted Power Frequency Band (MHz) Max Power (mW) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) 2412-2462 985.832 6.36 26 0.50193 1 5180-5240 129.773 5.8 26 0.05808 1 5745-5825 941.704 6.2 26 0.46212 1 NOTE: For 2412-2462MHz: Directional gain = 1.59dBi + 10log(3) = 6.36dBi For 5180-5240MHz: Directional gain = 1.03dBi + 10log(3) = 5.8dBi For 5745-5825MHz: Directional gain = 1.43dBi + 10log(3) = 6.2dBi Conclusion: Both of the 2.4GHz/5GHz can transmit simultaneously, the formula of calculated the MPE…

Text truncated - open the document above for the full version.

Report No.: RF150408C04-1 R2 Page No. 1 / 57 Report Format Version:6.1.1 Cancels and replaces the report No.: RF150408C04-1 R1 dated Oct. 28, 2015: FCC Test Report Report No.: RF150408C04-1 R2 FCC ID: TE7RE580D Test Model: RE580D Received Date: Apr. 08, 2015 Test Date: May 04 to Aug. 20, 2015 Issued Date: Nov. 19, 2015 Applicant: TP-LINK TECHNOLOGIES CO., LTD. Address: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150408C04-1 R2 Page No. 2 / 57 Report Format Version:6.1.1 Cancels and replaces the report No.: RF150408C04-1 R1 dated Oct. 28, 2015: Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................. 10 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................ 11 3.3 Duty Cycle of Test Signal .................................................................................................................. 13 3.4 Description of Support Units ............................................................................................................. 15 3.4.1 Configuration of System under Test .................................................................................................. 15 3.5 General Description of Applied Standard .......................................................................................... 16 4 Test Types and Results ...................................................................................................................... 17 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 17 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 17 4.1.2 Test Instruments ................................................................................................................................ 18 4.1.3 Test Procedures ................................................................................................................................. 20 4.1.4 Deviation from Test Standard ............................................................................................................ 20 4.1.5 Test Setup .......................................................................................................................................... 21 4.1.6 EUT Operating Conditions ................................................................................................................. 21 4.1.7 Test Results ....................................................................................................................................... 22 4.2 Conducted Emission Measurement .................................................................................................. 38 4.2.1 Limits of Conducted…

Text truncated - open the document above for the full version.

Report No.: 150211C05 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 150211C05 2 RADIATED EMISSION TEST (Below 1GHz) Report No.: 150211C05 3 RADIATED EMISSION TEST (Above 1GHz)