TE7SC3430NWireless N H.264 Megapixel Surveillance Camera

TL-SC3430N Wireless N H.264 Megapixel Surveillance Camera Rev: 1.0.0 1910010550 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. i CONTENTS CONTENTS ..........................................................................................................................i Package Contents..............................................................................................................1 Chapter 1 Safety Instructions..........................................................................................2 Chapter 2 Minimum System Requirement & Product Feature......................................3 2.1 System Requirement ........................................................................................................ 3 2.2 Product Features .............................................................................................................. 3 2.3 Physical Overview ............................................................................................................ 4 2.4 Mount the Camera ............................................................................................................ 6 2.5 Hardware Connection ....................................................................................................... 7 Chapter 3 Using IP Camera via Web Browser................................................................9 3.1 Obtain the IP Address ....................................................................................................... 9 3.2 Windows Web Browser....................................................................................................11 3.3 Mac Web Browser .......................................................................................................... 12 Chapter 4 Operating IP Camera via Mobile Phone ......................................................15 4.1 Mobile Phone Viewing .................................................................................................... 15 4.2 Using IP Camera via iPhone........................................................................................... 15 Chapter 5 Configuration of Main Menu ........................................................................17 5.1 Live View ........................................................................................................................ 17 5.2 Setting............................................................................................................................. 18 5.3 Client Setting ..................................................................................................................19 5.4 Image Setup ................................................................................................................... 20 Chapter 6 Setting-Basic.................................................................................................21 6.1 System............................................................................................................................ 21 6.2 Camera ........................................................................................................................... 24 6.3 Network........................................................................................................................... 33 6.4 Security........................................................................................................................... 48 Chapter 7 Setting-Advanced.........................................................................................51 7.1 FTP Client ....................................................................................................................... 51 7.2 SMTP.........................................................................................................…

Text truncated - open the document above for the full version.

20 5.3.4 Video Buffer .3.4 Video Buffer Turn the Video Buffer function On / Off. The Video Buffer function makes the streaming more smooth in unsteady network environment, but might cause a little delay in live viewing. Turn the Video Buffer function On / Off. The Video Buffer function makes the streaming more smooth in unsteady network environment, but might cause a little delay in live viewing. 5.4 Image Setup 5.4 Image Setup The tool bar can be adjusted to optimize video Brightness, Contrast, Saturation, Sharpness and Exposure. The tool bar can be adjusted to optimize video Brightness, Contrast, Saturation, Sharpness and Exposure. 5.4.1 Brightness The value range is 0~99. The higher value the brightness is, the brighter the image is. 5.4.2 Contrast The value range is 0~99. The contrast is a measure of a display system, defined as the ratio of white to black that the system is capable of producing. The higher value the contrast is, the more delicate of color you can have. 5.4.3 Saturation The value range is 0~99. The saturation of a color is determined by a combination of light intensity and how much it is distributed across the spectrum of different wavelengths. The higher value the saturation is, the more colorful the image will be . 5.4.4 Sharpness The value range is 0~99. It applies image processing techniques to adjust the sharpness of live view. However, the higher the value is, more the noise is. 5.4.5 Exposure The value range is 0~99. The higher value the exposure is, the brighter the image is. 5.4.6 Default After the adjustment of all setting, you can still click Default to make the setting back to the original setting. 21 Chapter 6 Setting-Basic Click the Basic folder to display the sub folders including System, Camera, Network, and Security. 6.1 System Click the folder of System to display the sub-folders including Information, Date / Time, Initialize, and Language. 6.1.1 Information The Information screen provides the product factory information which includes Product Name, Firmware Version. 22 6.1.2 Date / Time The Date/ Time screen displays all options of time setting.  Current Date / Time: This displays the current date and time of this IP Camera.  PC Clock: This displays the date and time of the monitoring PC clock.  Date / Time Format: You can click the pull down box to select different time display formats.  Note: If you would like the Date / Time information shows on the Live View screen, please check “Setting  Basic  Camera  General  Date / Time ” to execute the setting.  Adjust: You can select one of those four adjusting modes for your IP Camera.  Keep current setting: Select this mode to keep the current date and time of this IP Camera.  Synchronize: Select this mode to keep the date and time of this IP Camera is the same as the monitoring PC.  Manual setting: Select this mode to adjust manually the date and time of this IP Camera.  Synchronize with NTP: Specify the NTP server name and the Refresh Interval to synchronize the date and time of this IP Camera with those of the time server, known as the NTP server.  Time Zone: Select the Time Zone format of Greenwich Mean Time among different cities. The 23 time display will be the same as the current date / time option.  Daylight Saving Time: There are two modes to choose for setting up daylight saving time.  By Date: Set the start and end time by select month, day, hour, and minute.  By Week Number: Set the start and end time by select month, week, hour, and minute.  Note: The NTP server (Network Time Protocol) is the time server which is an Internet standard protocol built on the top of TCP / IP. This assures accurate synchronization to the millisecond of computer clock times in a network of computers. 6.1.3 Initialize  Reboot: Click this button to reboot this IP Camera. A confirmation dialogue will appear and then click “OK” to execute. It takes one minute to complete the reboot process.  Factory Default: Click this button to recover this IP Camera to the factory default setting. A confirmation dialogue will appear and then click “OK” to execute. The network indicator on this IP Camera will start to blink. This IP Camera will reboot automatically after completing adjustments to the default setting. Don't turn off this IP Camera until the device reboots.  Backup Setting: You can save the setting data of this IP Camera into a file. Click “Save” and follow the instructions on the browser to save the setting data file to the location you specified.  Restore Setting: Download the saved setting data of this IP Camera. Click “Browse” and select saved file. Click “OK” and this IP Camera is adjusted according to the loaded data and then restarted.  Firmware Update: Update the device software. Click “Browse” and select the file for updating. A confirmation dialogue will appear. Click “OK” to start. This IP Camera will reboot upon completion.  Note: When updating the firmware version, please use the file specific for the model. Otherwise, some problems may occur. Unless the updating completed, please don’t turn off the power or disconnect the network. 24 6.1.4 Language  Upload Language Pack: Clicking “Browse” and selecting the file for updating, the present language display of WEB User Interface could be changed. A confirmation dialogue will appear. Click “OK”, then the update will be applied immediately. The default language is “English”. 6.2 Camera Click the folder of Camera to display the sub folders including General, Stream 1, Stream 2, Advanced and Playback. 25 6.2.1 General  RTSP: The default value is 554. If the IP Cameras connected with router and installed outside are over 2 sets and all of them need support RTSP, please fill some value in the blank space in the range from 1024 to 65535.  RTP Unicast streaming: The default value of port range is 5000 ~ 7999 and can be changed from 1024 to 65535.  Note: Under Unicast streaming mode, streaming video is delivered from the Camera to a single…

Text truncated - open the document above for the full version.

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park,Nanshan Date: 2012‐01‐17 AUTHORIZATION LETTER To whom it may concern: We, the undersigned TP‐Link Technologies Co., Ltd., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park,Nanshan Date: 2012‐01‐17 FCC ID: TE7SC3430N To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

[email protected] www.adt.com.tw 致以 致以致以 致以 FCC DoC 方式行銷美國之客戶 方式行銷美國之客戶方式行銷美國之客戶 方式行銷美國之客戶 自1996年8月19日起，貴公司的產品如果是 PC 和 PC 之週邊類而要以 DoC 方式行銷美 國 (不須申請 FCC ID)，下列文件在以 DoC 方式行銷前必須準備齊全，以備 FCC 隨時抽查： 1. 測試報告 － 必須由 NVLAP 或 A2LA 認可之實驗室核發才有效。 2. Declaration of Conformity (DoC) Form － 必須由美國分公司或進口商簽名負責 (見附件 二)。 3. 原始之設計圖稿及規格書 (如：線路圖、方塊圖、User Manual 和 Service Manual 等)。 4. 敘述製造時之生產檢查程序，以確保 EMI 特性之維持。 5. 任何會影響到 EMI 的變更敘述和必要之測試記錄。 附註： * 產品上要貼上 DoC 要求之 Label 標示 (見附件一)。 * Label 上和 User Manual 內要有 FCC Statement (內容同以前 FCC ID 之作法)。 * DoC 簽名負責之廠商，有責任確保銷售之產品必須與當時檢驗樣品一樣，EMI 方面仍 符合規定。 * 以上文件 FCC 抽查時必須在14天內送達，如需測試樣品則必須在60天內送達，來 回運費由負責宣告 (DoC) 之廠商負責。 * 以上文件必須一份置於 DoC 簽名負責人手中備查。 誠信科技 敬啟 (附件一：FCC DoC Label 樣本) (For stand-alone test unit) (For unit assembled by modules with DoC) [email protected] www.adt.com.tw (附件二：FCC DoC 宣告信樣本) FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY (DoC) FOR THE FOLLOWING EQUIPMENT: PRODUCT NAME : Wireless N H.264 Megapixel Surveillance Camera MODEL NO : TL-SC3430N TRADE NAME : TP-LINK IS HEREWITH CONFIRMED AND FOUND TO COMPLY WITH THE REQUIREMENTS OF CFR 47 PART 15 REGULATION. THE RESULTS OF ELECTROMAGNETIC EMISSION EVALUATION ARE SHOWN IN THE REPORT NO.: FD120106C03 , ISSUED ON 2012/3/3. Tested By Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, located at No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND, (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THE FOLLOWING MANUFACTURER/IMPORTER IS RESPONSIBLE FOR THIS DECLARATION： (COMPANY NAME) (COMPANY ADDRESS) (TEL.) (FAX.) (NAME) (TITLE) (SIGNATURE) (DATE)

Report No.: 120106C03 1 Report Format Version 4.1.0 CONSTRUCTION PHOTOS OF EUT Report No.: 120106C03 6 Report Format Version 4.1.0 Model: MU12-S120100-A1 Report No.: 120106C03 7 Report Format Version 4.1.0

12 E D C B A 12 3456789 E D C 345678 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 记 录 与上一版的区别 TL-SC3430N英文标贴 第一版 80g艾利铜版纸+雾膜 TL-SC3430N\1.0.0\欧 2011-10-18 朱娜 白色 黑色 30%黑色 39.5*31.5mm,2R 文字转曲线

12 E D C B A 12 3456789 E D C 345678 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 记 录 与上一版的区别 TL-SC3430N英文标贴 第一版 80g艾利铜版纸+雾膜 TL-SC3430N\1.0.0\欧 2011-10-18 朱娜 白色 黑色 30%黑色 39.5*31.5mm,2R 文字转曲线

Report No.: 120106C03 2 Report Format Version 4.1.0 Report No.: 120106C03 3 Report Format Version 4.1.0 Report No.: 120106C03 4 Report Format Version 4.1.0 Report No.: 120106C03 5 Report Format Version 4.1.0

Report No.: SA120106C03 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA120106C03 MODEL NO.: TL-SC3430N FCC ID: TE7SC3430N RECEIVED: Jan. 06, 2012 TESTED: Feb. 03, 2012 ISSUED: Feb. 13, 2012 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 6 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA120106C03 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD....................................................................................3 1. CERTIFICATION......................................................................................................4 2. RF EXPOSURE LIMIT..............................................................................................5 3. MPE CALCULATION FORMULA.............................................................................5 4. CLASSIFICATION....................................................................................................5 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER...........................6 Report No.: SA120106C03 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA120106C03 Original release Feb. 13, 2012 Report No.: SA120106C03 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT: Wireless N H.264 Megapixel Surveillance Camera BRAND NAME: TP-LINK MODEL NO.: TL-SC3430N TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED DATE: Feb. 03, 2012 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: TL-SC3430N) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Feb. 05, 2012 ( Lori Chung, Specialist ) APPROVED BY : , DATE: Feb. 05, 2012 ( May Chen, Deputy Manager ) Report No.: SA120106C03 Report Format Version 4.0.0 5 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA120106C03 Report Format Version 4.0.0 6 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER 802.11b CHANNEL CHANNEL FREQUENCY (MHZ) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 1 2412 20.9 2.0 20 0.007 1.00 6 2437 20.4 2.0 20 0.006 1.00 11 2462 19.5 2.0 20 0.006 1.00 802.11g CHANNEL CHANNEL FREQUENCY (MHZ) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 1 2412 81.3 2.0 20 0.026 1.00 6 2437 77.6 2.0 20 0.024 1.00 11 2462 74.1 2.0 20 0.023 1.00 802.11n (20MHz) CHANNEL CHANNEL FREQUENCY (MHZ) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 1 2412 72.4 2.0 20 0.023 1.00 6 2437 69.2 2.0 20 0.022 1.00 11 2462 66.1 2.0 20 0.021 1.00 802.11n (40MHz) CHANNEL CHANNEL FREQUENCY (MHZ) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 3 2422 64.6 2.0 20 0.020 1.00 6 2437 64.6 2.0 20 0.020 1.00 9 2452 63.1 2.0 20 0.020 1.00 --- END ---

Report No.: RF120106C03 1 Report Format Version 4.1.0 FCC TEST REPORT REPORT NO.: RF120106C03 MODEL NO.: TL-SC3430N FCC ID: TE7SC3430N RECEIVED: Jan. 06, 2011 TESTED: Feb. 03 to 06, 2012 ISSUED: Feb. 13, 2012 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 64 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF120106C03 2 Report Format Version 4.1.0 Table of Contents RELEASE CONTROL RECORD........................................................................................4 1. CERTIFICATION....................................................................................................5 2. SUMMARY OF TEST RESULTS............................................................................6 2.1 MEASUREMENT UNCERTAINTY..........................................................................6 3. GENERAL INFORMATION.....................................................................................7 3.1 GENERAL DESCRIPTION OF EUT(WLAN)...........................................................7 3.2 DESCRIPTION OF TEST MODES.........................................................................9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL........................10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.......................................12 3.4 DESCRIPTION OF SUPPORT UNITS..................................................................13 3.5 CONFIGURATION OF SYSTEM UNDER TEST...................................................14 4. TEST TYPES AND RESULTS..............................................................................15 4.1 CONDUCTED EMISSION MEASUREMENT........................................................15 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT......................................15 4.1.2 TEST INSTRUMENTS..........................................................................................15 4.1.3 TEST PROCEDURES..........................................................................................16 4.1.4 DEVIATION FROM TEST STANDARD.................................................................16 4.1.5 TEST SETUP.......................................................................................................17 4.1.6 EUT OPERATING CONDITIONS.........................................................................17 4.1.7 TEST RESULTS...................................................................................................18 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT................................20 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT..............20 4.2.2 TEST INSTRUMENTS..........................................................................................21 4.2.3 TEST PROCEDURES..........................................................................................22 4.2.4 DEVIATION FROM TEST STANDARD.................................................................22 4.2.5 TEST SETUP.......................................................................................................23 4.2.6 EUT OPERATING CONDITIONS.........................................................................23 4.2.7 TEST RESULTS...................................................................................................24 4.3 6dB BANDWIDTH MEASUREMENT....................................................................37 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT..................................................37 4.3.2 TEST INSTRUMENTS..........................................................................................37 4.3.3 TEST PROCEDURE.............................................................................................37 4.3.4 DEVIATION FROM TEST STANDARD.................................................................37 4.3.5 TEST SETUP.......................................................................................................37 4.3.6 EUT OPERATING CONDITIONS.........................................................................37 4.3.7 TEST RESULTS...................................................................................................38 4.4 CONDUCTED OUTPUT POWER.........................................................................46 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT.....................46 4.4.2 INSTRUMENTS....................................................................................................46 4.4.3 TEST PROCEDURES..........................................................................................46 Report No.: RF120106C03 3 Report Format Version 4.1.0 4.4.4 DEVIATION FROM TEST STANDARD.................................................................46 4.4.5 TEST SETUP.......................................................................................................46 4.4.6 EUT OPERATING CONDITIONS.........................................................................46 4.4.7 TEST RESULTS...................................................................................................47 4.5 POWER…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST