TE7TDW8951NDV6150Mbps Wireless N ADSL2+ Modem Router

TD-W8951ND 150Mbps Wireless N ADSL2+ Modem Router Rev: 5.0.0 1910010973 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1） This device may not cause harmful interference. 2） This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the BOTTOM OF DEVICE is a label that contains, among other information, a product identifier in the format US: TPLDL01BTDW8951ND. If requested, this number must be provided to the telephone company. Applicable connector jack Universal Service Order Codes (“USOC”) for the Equipment is RJ11C . A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US: TPLDL01BTDW8951ND. The digits represented by 01B are the REN without a decimal point (e.g., 03 is a REN of 0.3). If this 150Mbps Wireless N ADSL2+ Modem Router causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. Part 68 telecom statement Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO EMERGENCY NUMBERS: 1) Remain on the line and briefly explain to the dispatcher the reason for the call. 2) Perform such activities in the off-peak hours, such as early morning or late evenings. If trouble is experienced with this 150Mbps Wireless N ADSL2+ Modem Router, for repair or warranty information, please contact975 Overland Ct, San Dimas, CA 91773 at +1 626-333-0234. If the …

Text truncated - open the document above for the full version.

TP-Link TP-Link TP-Link TP-LinkTechnologies Technologies Technologies TechnologiesCo., Co., Co., Co.,Ltd. Ltd. Ltd. Ltd. Building24(floors1,3,4,5)and28(floors1-4), CentralScienceandTechnologyPark,Nanshan,Shenzhen,China Date:2014-03-13 FCC FCC FCC FCCID: ID: ID: ID:TE7 TE7 TE7 TE7TDW8951ND TDW8951ND TDW8951ND TDW8951NDV V V V6 6 6 6 Totheattentionof Federal Federal Federal FederalCommunications Communications Communications CommunicationsCommission Commission Commission Commission AuthorizationandEvaluationDivision Confidentiality Confidentiality Confidentiality ConfidentialityRequest Request Request Request PursuanttoSections0.457and0.459oftheCommission’sRules,theApplicantherebyrequests confidentialtreatmentofinformationaccompanyingthisApplicationasoutlinedbelow: Schematics Schematics Schematics Schematics Block Block Block BlockDiagram Diagram Diagram Diagram Operational Operational Operational OperationalDescription Description Description Description Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleasedto thepublic.ThepublicdisclosureofthesemattersmightbeharmfultotheApplicantandprovide unjustifiedbenefitstoitscompetitors. TheApplicantunderstandsthatpursuanttoRule0.457,disclosureofthisApplicationandall accompanyingdocumentationwillnotbemadebeforethedateoftheGrantforthisapplication. Sincerelyyours, Name:YongquanWang TP-Link TP-Link TP-Link TP-LinkTechnologies Technologies Technologies TechnologiesCo., Co., Co., Co.,Ltd. Ltd. Ltd. Ltd. Tel.:+86-755-26502509 Fax.:+86-755-26508930 E-mail:[email protected]

TP-Link TP-Link TP-Link TP-LinkTechnologies Technologies Technologies TechnologiesCo., Co., Co., Co.,Ltd. Ltd. Ltd. Ltd. Building24(floors1,3,4,5)and28(floors1-4), CentralScienceandTechnologyPark,Nanshan,Shenzhen,China Date:2014-03-13 AUTHORIZATION AUTHORIZATION AUTHORIZATION AUTHORIZATIONLETTER LETTER LETTER LETTER Towhomitmayconcern: We,theundersignedTP-Link TP-Link TP-Link TP-LinkTechnologies Technologies Technologies TechnologiesCo., Co., Co., Co.,Ltd. Ltd. Ltd. Ltd., , , ,herebyauthorizeBureauVeritas ConsumerProductsServices(H.K.)Ltd.,TaoyuanBranch(BVCPSTaoyuan)ofTaiwantoactonour behalfinallmattersrelatingtoallprocessesrequiredinFCCapprovalandanycommunication neededwiththenationalauthority.AnyandallactscarriedoutbyBVCPSTaoyuanonourbehalf shallhavethesameeffectsasactsofourown. Ifyouhaveanyquestionsregardingtheauthorization,pleasedon’thesitatetocontactus. Thankyou! Sincerelyyours, Name:YongquanWang TP-Link TP-Link TP-Link TP-LinkTechnologies Technologies Technologies TechnologiesCo., Co., Co., Co.,Ltd. Ltd. Ltd. Ltd. Tel.:+86-755-26502509 Fax.:+86-755-26508930 E-mail:[email protected]

TP-LinkTechnologiesCo.,Ltd. Building24(floors1,3,4,5)and28(floors1-4), CentralScienceandTechnologyPark,Nanshan,Shenzhen,China AttestationforFCCDeclarationofConformity FCCID:TE7TDW8951NDV6Date:2014-03-13 Pleasebenotifiedthatwe,theundersigned,TP-LINKTECHNOLOGIESCO., LTDdeclarethattheproductbearstheaboveFCCIDisalsocomplyingwith therequirementsofFCCDoC.ThetestreportnumberforFCCDoCis FD131220C17,withisissuedbyanaccreditedlab,BureauVeritasConsumer ProductsServices(H.K.)Ltd.,TaoyuanBranch(BVCPSTaoyuan)ofTaiwan. Whichhasbeenaccreditedinaccordancetoalloftherequirementsof47CFR 2.948(d)and(e)oftheFCCrulesandKDB349827. Sincerely, Nameofauthorizedsigner:YongquanWang Titleofauthorizedsigner:ProductDept.Manager CompanyName:TP-LINKTechnologiesCo.,Ltd. Tel:86-755-26525554 Fax:86-755-26508930 Website:WWW.TP-LINK.COM E-mail:[email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3

  Label location

C B A 12 C 345678 B E D D A 9 料号： 12345 E 6789 与上一版的区别 颜 色 名 称 版 本 材 质 模 具 机型版本号 logo 底色 文字 其它 结构工程师 硬件工程师 产品工程师 平面负责人 记 录 审 核 完成日期 设 计

Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14

Report No.: SA131220C17 1 of 5 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA131220C17 MODEL NO.: TD-W8951ND FCC ID: TE7TDW8951NDV6 RECEIVED: Dec. 20, 2013 TESTED: Dec. 28 ~ Dec. 30, 2013 ISSUED: Jan. 17, 2014 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. Report No.: SA131220C17 2 of 5 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................. 4 2. RF EXPOSURE ............................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ......................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................... 5 2.3 CLASSIFICATION ........................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .................................. 5 Report No.: SA131220C17 3 of 5 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA131220C17 Original release Jan. 17, 2014 Report No.: SA131220C17 4 of 5 Report Format Version 5.0.0 1. Certification PRODUCT: 150Mbps Wireless N ADSL2+ Modem Router MODEL: TD-W8951ND BRAND: TP-LINK APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED: Dec. 28 ~ Dec. 30, 2013 TEST SAMPLE: PROTOTYPE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: TD-W8951ND) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Jan. 17, 2014 Maggie Wu / Specialist APPROVED BY : , DATE :Jan. 17, 2014 Ken Liu / Senior Manager Report No.: SA131220C17 5 of 5 Report Format Version 5.0.0 2. RF Exposure 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 Calculation result of maximum conducted power FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 23.96 5 20 0.1551 1

Report No.: RF131220C17 1 of 53 Report Format Version 5.2.0 FCC TEST REPORT REPORT NO.: RF131220C17 MODEL NO.: TD-W8951ND FCC ID: TE7TDW8951NDV6 RECEIVED: Dec. 20, 2013 TESTED: Dec. 28 ~ Dec. 30, 2013 ISSUED: Feb. 18, 2014 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF131220C17 2 of 53 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 4 1. CERTIFICATION ............................................................................................................................ 5 2. SUMMARY OF TEST RESULTS ................................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ............................................................................................................ 7 3.1 GENERAL DESCRIPTION OF EUT .............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................................................ 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................................ 9 3.3 DUTY CYCLE OF TEST SIGNAL ................................................................................................ 11 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................ 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................. 13 4. TEST TYPES AND RESULTS ..................................................................................................... 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................................................... 14 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................... 14 4.1.2 TEST INSTRUMENTS ................................................................................................................. 15 4.1.3 TEST PROCEDURES ................................................................................................................. 16 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................................... 16 4.1.5 TEST SETUP ............................................................................................................................... 17 4.1.6 EUT OPERATING CONDITIONS ................................................................................................ 18 4.1.7 TEST RESULTS .......................................................................................................................... 19 4.2 CONDUCTED EMISSION MEASUREMENT .............................................................................. 32 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................... 32 4.2.2 TEST INSTRUMENTS ................................................................................................................. 32 4.2.3 TEST PROCEDURES ................................................................................................................. 33 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................................... 33 4.2.5 TEST SETUP ............................................................................................................................... 33 4.2.6 EUT OPERATING CONDITIONS ................................................................................................ 33 4.2.7 TEST RESULTS .......................................................................................................................... 34 4.3 6dB BANDWIDTH MEASUREMENT ............................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST