TE7TDW8980V1N600 Wireless Dual Band Gigabit ADSL2+ Modem Router

TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router Rev: 1.0.0 1910010779 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to co mply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro vi de reasonable pro te ction against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or tel evision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an exp erienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference th at may cause undesired operation. Any changes or modifications not expressly approve d by the party responsible for co mpliance could void th e user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or tra nsmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation di stance of at least 20 cm from all persons and must not be co -located or operating in conjunction with any other antenna or transmitter.” CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Attention: Operations in the 5.15-5.25GHz band are restricted to indoor usage only. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications Note: Please don’t use the product outdoors in France. This device has been designed to operate with the antennas listed below, and having a maximum gain of 5dBi. Antennas not included in this list or having a gain greater than 5dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1)cet appareil ne doit pas provoquer d’interférences et (2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Korea Warning Statements: 당해 무선설비는 운용중 전파혼신 가능성이 있음. NCC Notice: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功 率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並 改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射…

Text truncated - open the document above for the full version.

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Attestation for FCC Declaration of Conformity FCC ID:TE7TDW8980V1 Date: 2013-07-24 Please be notified that we, the undersigned, TP-LINK TECHNOLOGIES CO., LTD declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC isFD130410C18, with is issued by an accredited lab, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP‐LINK Technologies Co., Ltd. Tel: 86‐755‐26525554 Fax: 86‐755‐26508930 Web site: WWW.TP‐LINK.COM E‐mail: public@tp‐link.com.cn

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China GUI Declaration letter Date: 2013-08-27 FCC ID: TE7TDW8980V1 To Whom It May Concern: We, TP-Link Technologies Co., Ltd. declare that the channel selection in the WLAN driver, is confined to the supported frequency band 802.11 a/n between 5.15 to 5.25 GHz and 5.725 to 5.8250GHz. The end user can only select the channel of the supported bands. Any other channel out of these frequency ranges can only be modified by using a special tool which is not be released； Furthermore, the firmware is locked by encrpytion tachniques and cannot be changed or modified by end user. Regarding hardware protection, TDW8980V1’s EEPROM adopts OTP (one time programming) architecture to storage RF parameters, country code, product information and others. User can not modify any setting parameter of OTP. Thank you for your attention. Sincerely yours, ----------------------------------- Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Te l . : +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Date: 2013‐07‐24 AUTHORIZATION LETTER To whom it may concern: We, the undersigned TP‐Link Technologies Co., Ltd., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4

Label location

C B A 12 C 345678 B E D D A 9 料号： 12345 E 6789 与上一版的区别 颜 色 名 称 版 本 材 质 模 具 机型版本号 logo 底色 文字 其它 结构工程师 硬件工程师 产品工程师 平面负责人 记 录 审 核 完成日期 设 计 TD-W8980(UN)1.0_产品规格标贴 A1 80g艾利铜版纸+雾膜 美F-243 TD-W8980(UN)1.0 娄喜萍 2012-10-22 Pantone 877C 黑色、白色 Pantone 877C Pantone 877C FCC ID:TE7TDW8980V1 IC:8853A-W8980 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Default Settings: Model: Power: N600 Wireless Dual Band Gigabit ADSL2+ Modem Router

Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11

Report No.: SA130410C18 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130410C18 MODEL NO.: TD-W8980 FCC ID: TE7TDW8980V1 RECEIVED: Apr. 10, 2013 TESTED: Jun. 11 ~ Jul. 26, 2013 ISSUED: Jul. 29, 2013 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. Report No.: SA130410C18 2 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................ 4 2. RF EXPOSURE .............................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................ 5 2.2 MPE CALCULATION FORMULA ................................................................................... 5 2.3 CLASSIFICATION .......................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................. 6 Report No.: SA130410C18 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130410C18 Original release Jul. 29, 2013 Report No.: SA130410C18 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: N600 Wireless Dual Band Gigabit ADSL2+ Modem Router MODEL NO.: TD-W8980 BRAND: TP-LINK APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED: Jun. 11 ~ Jul. 26, 2013 TEST SAMPLE: PRODUCTION SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: TD-W8980) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Jul. 29, 2013 Pettie Chen / Senior Specialist APPROVED BY : , DATE :Jul. 29, 2013 Ken Liu / Senior Manager Report No.: SA130410C18 5 of 6 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA130410C18 6 of 6 Report Format Version 5.0.0 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 21.90 3.5 20 0.069 1 5180-5240 16.83 5 20 0.030 1 5745-5825 27.39 5 20 0.345 1 CONCULSION: Both of the 2.4 and 5GHz can transmit simultaneously, the formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density 1. WLAN 2.4G + WLAN 5.0G = 0.069 + 0.345 = 0.414 Therefore, the maximum calculation of this situation is 0.414, which is less than the “1” limit.

Report No.: RF130410C18-2 1 of 32 Report Format Version 5.0.0 FCC TEST REPORT (CO-LOCATED) REPORT NO.: RF130410C18-2 MODEL NO.: TD-W8980 FCC ID: TE7TDW8980V1 RECEIVED: Apr. 10, 2013 TESTED: Jul. 29 ~ Jul. 30, 2013 ISSUED: Jul. 30, 2013 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130410C18-2 2 of 32 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .......................................................................................... 3 1. CERTIFICATION ................................................................................................ 4 2. SUMMARY OF TEST RESULTS ....................................................................... 5 2.1 MEASUREMENT UNCERTAINTY ..................................................................... 5 3. GENERAL INFORMATION ................................................................................ 6 3.1 GENERAL DESCRIPTION OF EUT .................................................................. 6 3.2 DESCRIPTION OF TEST MODES .................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................. 10 3.3 DESCRIPTION OF SUPPORT UNITS ............................................................ 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................. 12 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 12 4. TEST TYPES AND RESULTS ......................................................................... 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .......................... 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ....... 13 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ... 13 4.1.3 TEST INSTRUMENTS ..................................................................................... 14 4.1.4 TEST PROCEDURES ..................................................................................... 15 4.1.5 DEVIATION FROM TEST STANDARD ............................................................ 15 4.1.6 TEST SETUP ................................................................................................... 16 4.1.7 EUT OPERATING CONDITIONS .................................................................... 16 4.1.8 TEST RESULTS .............................................................................................. 17 4.2 CONDUCTED EMISSION MEASUREMENT .................................................. 23 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ................................ 23 4.2.2 TEST INSTRUMENTS ..................................................................................... 23 4.2.3 TEST PROCEDURES ..................................................................................... 24 4.2.4 DEVIATION FROM TEST STANDARD ............................................................ 24 4.2.5 TEST SETUP ................................................................................................... 25 4.2.6 EUT OPERATING CONDITIONS .................................................................... 25 4.2.7 TEST RESULTS .............................................................................................. 26 5. PHOTOGRAPHS OF THE TEST CONFIGURATION ...................................... 30 6. INFORMATION ON THE TESTING LABORATORIES .................................... 31 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ........................................................... 32 Report No.: RF130410C18-2 3 of 32 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF130410C18-2 Original release Jul. 30, 2013 Report No.: RF130410C18-2 4 of 32 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: N600 Wireless Dual Band Gigabit ADSL2+ Modem Router MODEL NO.: TD-W8980 BRAND: TP-LINK APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED: Jul. 29 ~ Jul. 30, 2013 TEST SAMPLE: PRODUCTION SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.247) FCC Part 15, Subpart E (Section 15.407) ANSI C63.10-2009 The above equipment (model: TD-W8980) has been test…

Text truncated - open the document above for the full version.

Report No.: RF130410C18-1 1 of 50 Report Format Version 5.1.0 FCC TEST REPORT (15.407) REPORT NO.: RF130410C18-1 MODEL NO.: TD-W8980 FCC ID: TE7TDW8980V1 RECEIVED: Apr. 10, 2013 TESTED: Jun. 11 ~ Jul. 26, 2013 ISSUED: Jul. 29, 2013 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130410C18-1 2 of 50 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 4 1. CERTIFICATION .................................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY ......................................................................................... 6 3. GENERAL INFORMATION ..................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ....................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ......................................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................................ 9 3.3 DUTY CYCLE OF TEST SIGNAL ........................................................................................ 11 3.4 DESCRIPTION OF SUPPORT UNITS ................................................................................. 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................................. 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ...................................................... 14 4. TEST TYPES AND RESULTS .............................................................................................. 15 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .............................................. 15 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ........................... 15 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ....................... 15 4.1.3 TEST INSTRUMENTS ......................................................................................................... 16 4.1.4 TEST PROCEDURES .......................................................................................................... 17 4.1.5 DEVIATION FROM TEST STANDARD ................................................................................ 17 4.1.6 TEST SETUP ........................................................................................................................ 18 4.1.7 EUT OPERATING CONDITION ........................................................................................... 18 4.1.8 TEST RESULTS ................................................................................................................... 19 4.2 CONDUCTED EMISSION MEASUREMENT ....................................................................... 29 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .................................................... 29 4.2.2 TEST INSTRUMENTS ......................................................................................................... 29 4.2.3 TEST PROCEDURES .......................................................................................................... 30 4.2.4 DEVIATION FROM TEST STANDARD ................................................................................ 30 4.2.5 TEST SETUP ........................................................................................................................ 30 4.2.6 EUT OPERATING CONDITIONS ......................................................................................... 30 4.2.7 TEST RESULTS ................................................................................................................... 31 4.3 PEAK TRANSMIT POWER MEASUREMENT ..................................................................... 33 4.3.1 LIMITS OF PEAK TRANSMIT POWER MEASUREMENT ..................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST