TE7TLWPA4220V1300Mbps Wi-Fi Range Extender, AV500 Powerline Edition

TL-WPA4220 300Mbps AV500 WiFi Powerline Extender TL-WPA2220 300Mbps AV200 WiFi Powerline Extender REV1.0.1 1910010839 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Про дук т сер тифік ов ано згідно с правил ами сис теми УкрСЕПР О на відп ові дність вимог ам нормативних док ументі в та вимогам, що пере дбачені чинними зак оно дав чими актами України. Safety Information When product has power button, the power button is one of th e way to shut of f the product; when there is no power button, the only way to completely shut of f power is to disconnect the product or the power adapter from the power source. Don’t disassemble the pr oduct, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need se rvi ce , please contact us. Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SK TR UA Where the MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable. Attention: The equipment can only be used in below directions. TP-LINK TECHNOLOGIES CO., LTD TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps AV500/AV200 WiFi Powerline Extender Model No.: TL-WPA4220/TL-WPA2220 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.2.1:2012 EN 55022:2010 EN 55024:2010 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008 EN 60950-1:2006+A11：2009+A1:2010+A12:2011 EN 62311:2008 The product carries the CE Mark: Person responsible for marking this declaration: Yang Hongliang Product Manager of International Business Date of issue: 2013 Important Safety Instructions 1. Do not open this product or attempt to service it; it may expose you to dangerous high voltage or other risks. 2. Do not operate this product near water. 3. Do not place or operate this product near a radiator or a heat register. 4. Do not expose this product to dampness, dust or corrosive liquids. 5. Do not connect this product or disconnect it from a wall socket during a lightning or a thunderstorm. 6. Do not block the ventilation slots of this product, for insufficient airflow may harm it. 7. Do not put anything on this product. 8. Plug this product directly into a wall socket (100-240V~, 50/60Hz). Do not use an extension cord between this product and the AC power source. 9. When plugging this product into a wall socket, make s…

Text truncated - open the document above for the full version.

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Declaration for no non‐US channel operation November 21, 2013 We, TP‐Link Technologies Co., Ltd., declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: TE7TLWPA4220V1 If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Date: 2013‐09‐26 FCC ID: TE7TLWPA4220V1 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0. 459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

Attestation for FCC Declaration of Conformity FCC ID: TE7TLWPA4220V1 Date: 2013-9-26 Please be notified that we, the undersigned, TP-LINK TECHNOLOGIES CO., LTD declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC is FD130701C15A, wit h is issued by an accredited lab, Bureau Veritas Consumer Products Services(H.K.) Ltd., Taoyuan Branch located at No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP-LINK Technologies Co., Ltd. Tel: 86-755-26525554 Fax: 86-755-26508930 Web site: WWW.TP-LINK.COM E-mail: [email protected]

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Date: 2013‐09‐26 AUTHORIZATION LETTER To whom it may concern: We, the undersigned TP‐Link Technologies Co., Ltd., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Label location

Page 3 Page 4 Page 5 Page 6

Report No.: SA130701C15A R1 1 of 5 Report Format Version 5.0.0 Reference No.: 130813C10 Cancels and replaces the report No.: SA130701C15A dated Sep. 25, 2013 RF EXPOSURE REPORT REPORT NO.: SA130701C15A R1 MODEL NO.: TL-WPA4220 FCC ID: TE7TLWPA4220V1 RECEIVED: Aug. 13, 2013 TESTED: Aug. 19 ~ Sep. 17, 2013 ISSUED: Oct. 28, 2013 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1, 3, 4, 5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA130701C15A R1 2 of 5 Report Format Version 5.0.0 Reference No.: 130813C10 Cancels and replaces the report No.: SA130701C15A dated Sep. 25, 2013 TABLE OF CONTENTS RELEASE CONTROL RECORD .................................................................................................. 3 1. CERTIFICATION ............................................................................................................... 4 2. RF EXPOSURE ................................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................... 5 2.2 MPE CALCULATION FORMULA ...................................................................................... 5 2.3 CLASSIFICATION ............................................................................................................. 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .................................... 5 Report No.: SA130701C15A R1 3 of 5 Report Format Version 5.0.0 Reference No.: 130813C10 Cancels and replaces the report No.: SA130701C15A dated Sep. 25, 2013 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130701C15A Original release. Sep. 25, 2013 SA130701C15A R1 Change product name. Oct. 28, 2013 Report No.: SA130701C15A R1 4 of 5 Report Format Version 5.0.0 Reference No.: 130813C10 Cancels and replaces the report No.: SA130701C15A dated Sep. 25, 2013 1. CERTIFICATION PRODUCT: 300Mbps Wi-Fi Range Extender, AV500 Powerline Edition MODEL: TL-WPA4220 BRAND: TP-LINK APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED: Aug. 19 ~ Sep. 17, 2013 TEST SAMPLE: PRODUCTION SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: TL-WPA4220) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Oct. 28, 2013 Suntee Liu / Specialist APPROVED BY : , DATE : Oct. 28, 2013 Ken Liu / Senior Manager Report No.: SA130701C15A R1 5 of 5 Report Format Version 5.0.0 Reference No.: 130813C10 Cancels and replaces the report No.: SA130701C15A dated Sep. 25, 2013 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 27.51 2 20 0.178 1 ---END---

Report No.: RF130701C15A R1 1 of 67 Report Format Version 5.2.0 Reference No.: 130813C10 Cancels and replaces the report No.:RF130701C15A dated Sep. 25, 2013 FCC TEST REPORT REPORT NO.: RF130701C15A R1 MODEL NO.: TL-WPA4220 FCC ID: TE7TLWPA4220V1 RECEIVED: Aug. 13, 2013 TESTED: Aug. 19 ~ Sep. 17, 2013 ISSUED: Oct. 28, 2013 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1, 3, 4, 5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130701C15A R1 2 of 67 Report Format Version 5.2.0 Reference No.: 130813C10 Cancels and replaces the report No.:RF130701C15A dated Sep. 25, 2013 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 4 1. CERTIFICATION ....................................................................................................................... 5 2. SUMMARY OF TEST RESULTS .............................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ............................................................................................ 6 3. GENERAL INFORMATION ....................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ......................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ........................................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................................... 9 3.3 DUTY CYCLE OF TEST SIGNAL ........................................................................................... 11 3.4 DESCRIPTION OF SUPPORT UNITS ................................................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................................... 13 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................................ 14 4. TEST TYPES AND RESULTS ................................................................................................ 15 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................................. 15 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............................. 15 4.1.2 TEST INSTRUMENTS ............................................................................................................ 16 4.1.3 TEST PROCEDURES ............................................................................................................. 17 4.1.4 DEVIATION FROM TEST STANDARD ................................................................................... 17 4.1.5 TEST SETUP .......................................................................................................................... 18 4.1.6 EUT OPERATING CONDITIONS ........................................................................................... 19 4.1.7 TEST RESULT ........................................................................................................................ 20 4.2 CONDUCTED EMISSION MEASUREMENT ......................................................................... 39 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ....................................................... 39 4.2.2 TEST INSTRUMENTS ............................................................................................................ 39 4.2.3 TEST PROCEDURES ............................................................................................................. 40 4.2.4 DEVIATION FROM TEST STANDARD ................................................................................... 40 4.2.5 TEST SETUP .......................................................................................................................... 40 4.2.6 EUT OPERATING CONDITIONS ........................................................................................... 40 4.2.7 TEST RESULTS ...................................................................................................................... 41 4.3 6DB BANDWIDTH MEASUREMENT ...…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST