TE7WDN3200N600 Wireless Dual Band USB Adapter

TL-WDN3200 N600 Wireless Dual Band USB Adapter Rev: 1.0.0 1910010577 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand. SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy None If used outside of own premises, general authorization is required Lu xembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications Note: Please don’t use the product outdoors in France. Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) Le dispositif ne doit pa s produire de brouillage préjudiciable, et (2) Ce dispositif doit accepter tout brouillage reçu,y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Korea Warning Statements: 당해 무선설 비는 운용중 전파혼신 가능성이 있음. NCC Notice: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用， 並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射 頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 如有這頻率： 於 5.25GHz至5.35GHz區域內操作之無線設備的警告聲明 工作頻率5.250~5.350GHz該頻段限於室內使用。 This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Safety Information � When product has power button, the power button is one of the way to shut off the product; When there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. � Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. � Avoid water and wet locations. � This is a domestic product, and please make sure of the indoor use. TP-LINK TECHNOLOGIES CO., LTD TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARATION OF CONFORMITY For the following equipment: Product Description: N600 Wireless Dual Band USB Adapter Model No.: TL-WDN3200 Tradem…

Text truncated - open the document above for the full version.

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park,Nanshan Date: 2012-04-05 A U T H O R I Z A T I O N L E T T E R To whom it may concern: We, the undersigned TP-Link Technologies Co., Ltd., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name: Yongquan Wang TP-Link Technologies Co., Ltd. Tel.: +86-755-26502509 Fax.: +86-755-26508930 E-mail: [email protected]

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park,Nanshan Date: 2012-04-05 FCC ID: TE7WDN3200 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Yongquan Wang TP-Link Technologies Co., Ltd. Tel.: +86-755-26502509 Fax.: +86-755-26508930 E-mail: [email protected]

Attestation for FCC Declaration of Conformity FCC ID: TE7WDN3200 Date: 2012-4-10 Please be notified that we, the undersigned, TP-LINK TECHNOLOGIES CO., LTD declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC is FD120328C07, with is issued by an accredited lab, Audix Technology Corporation, EMC Department located at No. 53-11, Tin-Fu Tsun, Lin-Kou , Taipei Hsien , Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP-LINK Technologies Co., Ltd. Tel: 86-755-26525554 Fax: 86-755-26508930 Web site: WWW.TP-LINK.COM E-mail: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Label Location

TL-WDN3200（UN）1.0产品规格标贴 A2 80#合成纸+可打印雾膜 TL-WDN3200（UN）1.0 2011-12-21 白色 PANTONE 426C 白色 葛焕丽 更改产品名称，添加IC Number 12 E D C B A 12 3456789 E D C 345678 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 记 录 与上一版的区别 39.7*9.7mm, 1R 文字转曲 放大效果图（2：1） (为示意码，由工厂打印) N600 Wireless Dual Band USB Adapter FCC ID: TE7WDN3200 MADE IN CHINA Model:TL-WDN3200 N28505 IC:8853A-WDN3200

Page 3 Page 4

FCC SAR Test Report Report Format Version 4.1.0 Page No. : 1 of 22 Report No. : SA120328C07 Issued Date : May 22, 2012 Revision : R01 FCC SAR Test Report Report No. : SA120328C07 Applicant : TP-LINK TECHNOLOGIES CO., LTD. Address : Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China Product : N600 Wireless Dual Band USB Adapter FCC ID : TE7WDN3200 Brand : TP-LINK Model No. : TL-WDN3200 Standards : FCC 47 CFR Part 2 (2.1093) / IEEE C95.1:1991 / IEEE 1528:2003 FCC OET Bulletin 65 Supplement C (Edition 01-01) KDB 248227 D01 v01r02 / KDB 447498 D01 v04 / KDB 447498 D02 v02 Date of Testing : Apr. 23, 2012 ~ May 09, 2012 CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch - Taiwan HwaYa Lab, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. This test report consists of 22 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Prepared By : Ivonne Wu / Senior Specialist Approved By : Roy Wu / Manager FCC SAR Test Report Report Format Version 4.1.0 Page No. : 2 of 22 Report No. : SA120328C07 Issued Date : May 22, 2012 Revision : R01 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ................................................................................................................ 6 3.2 SPEAG DASY System ................................................................................................................................................. 6 3.2.1 Robot.................................................................................................................................................................. 7 3.2.2 Probes ................................................................................................................................................................ 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................... 8 3.2.4 Phantoms ........................................................................................................................................................... 9 3.2.5 Device Holder ................................................................................................................................................... 10 3.2.6 System Validation Dipoles ................................................................................................................................ 10 3.2.7 Tissue Simulating Liquids ................................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 12 3.4 SAR Measurement Procedure ................................................................................................................................... 13 3.4.1 Area & Zoom Scan Procedure ......................................................................................................................... 13 3.4.2 Volume Scan Procedure................................................................................................................................... 13 3.4.3 Power Drift Monitoring ...................................................................................................................................... 13 3.4.4 Spatial Peak SAR Evaluation ........................................................................................................................... 14 3.4.5 SAR Averaged Methods ................................................................................................................................... 14 4. SAR Measurement Evaluation ............................................................................................................................................ 15 4.1 EUT Configuration and Setting ................................................................................................................................... 15 4.2 EUT Testing Position .................................................................................................................................................. 16 4.3 Tissue Verification ...................................................................................................................................................... 16 4.4 System Verification ..................................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF120328C07 1 of 54 Report Format Version 5.0.0 FCC TEST REPORT (15.407) REPORT NO.: RF120328C07 MODEL NO.: TL-WDN3200 FCC ID: TE7WDN3200 RECEIVED: Mar. 28, 2012 TESTED: Apr. 6 ~ 12, 2012 ISSUED: Aug. 6, 2012 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist.,New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF120328C07 2 of 54 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD................................................................................. 4 1. CERTIFICATION ............................................................................................ 5 2. SUMMARY OF TEST RESULTS .................................................................... 6 2.1 MEASUREMENT UNCERTAINTY.................................................................. 6 3. GENERAL INFORMATION ............................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................... 7 3.2 DESCRIPTION OF TEST MODES ................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................. 9 3.3 DUTY CYCLE OF TEST SIGNAL ..................................................................11 3.4 DESCRIPTION OF SUPPORT UNITS ......................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................. 13 4. TEST TYPES AND RESULTS ...................................................................... 14 4.1 CONDUCTED EMISSION MEASUREMENT ............................................... 14 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................. 14 4.1.2 TEST INSTRUMENTS ................................................................................. 14 4.1.3 TEST PROCEDURES .................................................................................. 15 4.1.4 DEVIATION FROM TEST STANDARD ........................................................ 15 4.1.5 TEST SETUP ............................................................................................... 16 4.1.6 EUT OPERATING CONDITIONS ................................................................. 16 4.1.7 TEST RESULTS ........................................................................................... 17 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ....................... 19 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .... 19 4.2.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS 19 4.2.3 TEST INSTRUMENTS ................................................................................. 20 4.2.4 TEST PROCEDURES .................................................................................. 21 4.2.5 DEVIATION FROM TEST STANDARD ........................................................ 21 4.2.6 TEST SETUP ............................................................................................... 22 4.2.7 EUT OPERATING CONDITION ................................................................... 22 4.2.8 TEST RESULTS ........................................................................................... 23 4.3 PEAK TRANSMIT POWER MEASUREMENT ............................................. 32 4.3.1 LIMITS OF PEAK TRANSMIT POWER MEASUREMENT ........................... 32 4.3.2 TEST SETUP ............................................................................................... 32 4.3.3 TEST INSTRUMENTS ................................................................................. 32 4.3.4 TEST PROCEDURE .................................................................................... 33 4.3.5 DEVIATION FROM TEST STANDARD ........................................................ 33 4.3.6 EUT OPERATING CONDITIONS ................................................................. 33 4.3.7 TEST RESULTS ........................................................................................... 34 4.4 PEAK POWER SPECTRAL DENSITY MEASUREMENT ............................ 38 4.4.1 LIMITS OF PEAK POWER SPECTRAL DENSITY MEASUREMENT .......... 38 4.4.2 TEST SETUP ...............................................................................…

Text truncated - open the document above for the full version.

IC SAR Test Report Report Format Version 5.0.0 Report No. : SA120328C07B Reference No.: 120803C10 Revision : R01 <Photographs of EUT> <Location of Antennas> IC SAR Test Report Report Format Version 5.0.0 Report No. : SA120328C07B Reference No.: 120803C10 Revision : R01 <Photographs of SAR Setup> Horizontal Up with 5 mm Gap Horizontal Down with 5 mm Gap Vertical Front with 5 mm Gap Vertical Back with 5 mm Gap Tip Mode with 5 mm Gap

Report No.:RF120328C07 1 Report Format Version 4.2.0 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.:RF120328C07 2 Report Format Version 4.2.0 RADIATED EMISSION TEST