TE7WN723NV2150Mbps Mini Wireless N USB Adapter

TL-WN723N 150Mbps Mini Wireless N USB Adapter Rev: 2.0.1 1910010539 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment is a portable equipment andcomplies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand.SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remark Bulgaria General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation Only for indoor applications Note: Please don’t use the product outdoors in France. This device has been designed to operate with the antennas listed below which have a maximum gain of 2 dBi. Antennas not included in this list or having a gain greater than 2 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations:Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé.Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible. NOTE IMPORTANTE: Déclaration d’exposition aux radiations: Cet équipement est un équipement portable et conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Korea Warning Statements: 당해 무선설비는 운용중 전파혼신 가능성이 있음. NCC Notice: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原…

Text truncated - open the document above for the full version.

Attestation for FCC Declaration of Conformity FCC ID: TE7WN723NV2 Date: 2012-3-9 Please be notified that we, the undersigned, TP-LINK TECHNOLOGIES CO., LTD declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC is FD120102C04, with is issued by an accredited lab, Bureau Veritas Consumer Products Services(H.K.) Ltd., Taoyuan Branch located at No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: TP-LINK Technologies Co., Ltd. Tel: 86-755-26525554 Fax: 86-755-26508930 Web site: WWW.TP-LINK.COM E-mail: [email protected]

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park,Nanshan Date: 2012‐02‐27 FCC ID: TE7WN723NV2 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park,Nanshan Date: 2012‐02‐27 AUTHORIZATION LETTER To whom it may concern: We, the undersigned TP‐Link Technologies Co., Ltd., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

12 E D C B A 12 3456789 E D C 345678 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 记 录 与上一版的区别 TL-WN723N(UN) 2.0 USB端口丝印 TL-WN723N(UN) 2.0 2011-12-15 黑色 黑色 PANTONE877C 陈静雯 反面 12 7.16 12 5.16 零件图 丝印颜色：黑色 & 银色PANTONE877C TL-WN723N FCC ID:TE7WN723NV2 IC: 8853A-WN723NV2 Model:

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA1112-2131SAR01R1 Page 1 of 64 TESTING No. L2264 TEST REPORT Product Name 150Mbps Mini Wireless N USB Adapter Model TL-WN723N FCC ID TE7WN723NV2 IC 8853A-WN723NV2 Client TP-LINK TECHNOLOGIES CO., LTD. TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA1112-2131SAR01R1 Page 2 of 64 GENERAL SUMMARY Product Name 150Mbps Mini Wireless N USB Adapter Model TL-WN723N FCC ID TE7WN723NV2 IC 8853A-WN723NV2 Report No. RZA1112-2131SAR01R1 Client TP-LINK TECHNOLOGIES CO., LTD. Manufacturer TP-LINK TECHNOLOGIES CO., LTD. Reference Standard(s) IEEE Std C95.1, 1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. SUPPLEMENT C Edition 01-01 to OET BULLETIN 65 Edition 97-01 June 2001 including DA 02-1438, published June 2002: Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields Additional Information for Evaluation Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radio frequency Emissions. RSS-102 Issue 4 March 2010: Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) KDB 248227 D01 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters. KDB 447498 D02 SAR Procedures for Dongle Xmtr v02: SAR Measurement Procedures for USB Dongle Transmitters. Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards. General Judgment: Pass (Stamp) Date of issue: February 29 th , 2012 Comment The test result only responds to the measured sample. Approved by Director Revised by SAR Manager Performed by SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RZA1112-2131SAR01R1 Page 3 of 64 TABLE OF CONTENT 1. General Information ..................................................................................................................... 5 1.1. Notes of the Test Report.......................................................................................................5 1.2. Testing Laboratory ................................................................................................................ 5 1.3. Applicant Information ............................................................................................................ 6 1.4. Manufacturer Information ...................................................................................................... 6 1.5. Information of EUT................................................................................................................ 7 1.6. The Maximum SAR 1g Values ................................................................................................ 8 1.7. Test Date .............................................................................................................................. 8 2. SAR Measurements System Configuration .................................................................................. 9 2.1. SAR Measurement Set-up .................................................................................................... 9 2.2. DASY4 E-field Probe System ............................................................................................. 10 2.2.1. EX3DV4 Probe Specification ....................................................................................... 10 2.2.2. E-field Probe Calibration .............................................................................................. 11 2.3. Other Test Equipment ......................................................................................................... 11 2.3.1. Device Holder for Transmitters .................................................................................... 11 2.3.2. Phantom...................................................................................................................... 12 2.4. Scanning Procedure........................................................................................................... 12 2.5. Data Storage and Evaluation .............................................................................................. 14 2.5.1. Data Storage................................................................................................................ 14 2.5.2. Data Evaluation by SEMCAD ...................................................................................... 14 3. Laboratory Environment............................................................................................................. 16 4. Tissue-equivalent Liquid ............................................................................................................ 17 4.1. Tissue-equivalent Liquid Ingredients................................................................................... 17 4.2. Tissue-equivalent Liquid Properties .................................................................................... 17 5. Systerm Check........................................................................................................................... 18 5.1. Description of System Check .............................................................................................. 18 5.2. System Check Results ........................................................................................................ 19 6. Operational Conditions during Test ............................................................................................ 20 6.1. General Description of Test Procedures............................................................................. 20 6.2. Test Positions...............................................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF120102C04 1 Report Format Version 4.1.0 FCC & IC TEST REPORT REPORT NO.: RF120102C04 MODEL NO.: TL-WN723N FCC ID: TE7WN723NV2 IC: 8853A-WN723NV2 RECEIVED: Jan. 2, 2012 TESTED: Jan. 6 ~ Feb. 10, 2012 ISSUED: Feb. 17, 2012 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist.,New Taipei City, Taiwan ( R.O.C. ) This test report consists of 71 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF120102C04 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD..................................................................................4 1. CERTIFICATION..........................................................................................5 2. SUMMARY OF TEST RESULTS.................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................6 3. GENERAL INFORMATION..........................................................................7 3.1 GENERAL DESCRIPTION OF EUT............................................................7 3.2 DESCRIPTION OF TEST MODES..............................................................9 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST..........................................9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL.............10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS............................13 3.4 DESCRIPTION OF SUPPORT UNITS.......................................................13 4. TEST TYPES AND RESULTS....................................................................14 4.1 CONDUCTED EMISSION MEASUREMENT.............................................14 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................14 4.1.2 TEST INSTRUMENTS...............................................................................15 4.1.3 TEST PROCEDURES...............................................................................16 4.1.4 DEVIATION FROM TEST STANDARD......................................................16 4.1.5 TEST SETUP.............................................................................................17 4.1.6 EUT OPERATING CONDITIONS...............................................................17 4.1.7 TEST RESULTS........................................................................................18 4.2 RADIATED EMISSION MEASUREMENT..................................................20 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...............................20 4.2.2 TEST INSTRUMENTS...............................................................................21 4.2.3 TEST PROCEDURES...............................................................................22 4.2.4 DEVIATION FROM TEST STANDARD......................................................22 4.2.5 TEST SETUP.............................................................................................23 4.2.6 EUT OPERATING CONDITIONS...............................................................23 4.2.7 TEST RESULTS........................................................................................24 4.3 6dB BANDWIDTH MEASUREMENT.........................................................37 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT.......................................37 4.3.2 TEST SETUP.............................................................................................37 4.3.3 TEST INSTRUMENTS...............................................................................37 4.3.4 TEST PROCEDURE..................................................................................37 4.3.5 DEVIATION FROM TEST STANDARD......................................................37 4.3.6 EUT OPERATING CONDITIONS...............................................................37 4.3.7 TEST RESULTS........................................................................................38 4.4 CONDUCTED OUTPUT POWER..............................................................42 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT...............42 4.4.2 TEST SETUP.............................................................................................42 4.4.3 TEST INSTRUMENTS...............................................................................42 4.4.4 TEST PROCEDURES...............................................................................42 4.4.5 DEVIATION FROM TEST STANDARD......................................................42 4.4.6 EUT OPERATING CONDITIONS...............................................................42 Report No.: RF120102C04 3 Report Format Version 4.1.0 4.4.7 TEST RESULTS........................................................................................43 4.5 POWER SPECTRAL DENSITY MEASUREMENT....................................45 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT..................45 4.5.2 TEST SETUP.............................................................................................45 4.5.3 TEST INSTRUMENTS...............................................................................45 4.5.4 TEST PROCEDURE..................................................................................45 4.5.5 DEVIATION FROM TEST STANDARD......................................................45 4.5.6 EUT OPERATING CONDITION.................................................................45 4.5.7 TEST RESULTS.......................…

Text truncated - open the document above for the full version.

Report No.: RF120102C04 1 Report Format Version 4.1.0 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF120102C04 2 Report Format Version 4.1.0 RADIATED EMISSION TEST