TE7WR2543N450Mbps Dual-Band Wireless N Gigabit Router

TL-WR2543ND 450Mbps Dual-Band Wireless N Gigabit Router Rev: 1.0.0 1910010514 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. For operation within 5.15-5.25GHz frequency range, it is restricted to indoor environment. For products in the USA market, only channel 1-11 can be operated. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” CE Mark Warning National restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service Italy None If used outside of own premises, general authorization is required Lu xembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications This device has been designed to operate with the antennas listed below, and having a maximum gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. No. of this DoC: TP-120904 Company: TP-LINK TECHNOLOGIES CO., LTD. We declare under our own responsibility for the following equipment: Product Description: 450Mbps Dual-Band Wireless N Gigabit Router Model No.:TL-WR2543ND Trademark: TP-LINK The above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC, 2004/108/EC, 2009/125/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents: EN 300 328 V1.7.1: 2006-10 EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.1.1:2009-05 EN 301 893 V1.6.1:2011 EN 55022:2010 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008 EN 55024:2010 EN60950-1:2006+A11:2009+A1:2010+A12:2011 EN62311:2008 EN62075:2008 IEC/PAS62596, IEC62321 Person is responsible for marking this declaration: Yang Hongliang Product Manager of International Business Date of Issue: 2012.9.4 ADD: Building 24(floors 1,3,4,5) and 28(floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen,China Website: www.tp-link.com TP-LINK TECHNOLOGIES CO., LTD TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for…

Text truncated - open the document above for the full version.

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Date: 2012‐09‐04 AUTHORIZATION LETTER To whom it may concern: We, the undersigned TP‐Link Technologies Co., Ltd., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

TP-Link Technologies Co., Ltd. Building 24 (floors 1,3,4,5) and 28 (floors1-4), Central Science and Technology Park, Nanshan, Shenzhen, China Date: 2012‐09‐04 FCC ID: TE7WR2543N To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name: Yongquan Wang TP‐Link Technologies Co., Ltd. Tel.: +86‐755‐26502509 Fax.: +86‐755‐26508930 E‐mail: public@tp‐link.com.cn

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

TL-WR2543ND(UN)产品规格标贴 A3 80g艾利铜版纸+雾膜 TL-WR2543ND( UN) 1.0 2011-11-15 修改c-tick图标大小 白色 Pantone Cool gray 9C、白 色 Pantone Cool gray 9C 12 E D C B A 12 3456789 E D C 345678 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 与上一版的区别 记 录 68.48*39mm, 6R Pantone Cool gray 9C 文字已转曲 http://tplinklogin.net Model: TL-WR2543ND Power: 12V 1.5A 450Mbps Dual-Band Wireless N Gigabit Router FCC ID:TE7WR2543N This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Default Access: S/N PIN MAC IC:8853A-WR2543N IC:8853A-WR2543N Label location

Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10

Report No.: SA120301C28 1 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA120301C28 MODEL NO.: TL-WR2543ND FCC ID: TE7WR2543N RECEIVED: Mar. 1, 2012 TESTED: Jul. 25 ~ Aug. 1, 2012 ISSUED: Aug. 30, 2012 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA120301C28 2 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD.................................................................................3 1. CERTIFICATION...........................................................................................4 2. RF EXPOSURE LIMIT...................................................................................5 3. MPE CALCULATION FORMULA..................................................................5 4. CLASSIFICATION.........................................................................................5 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER................6 Report No.: SA120301C28 3 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA120301C28 Original release Aug. 30, 2012 Report No.: SA120301C28 4 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: 450Mbps Dual-Band Wireless N Gigabit Router MODEL NO.: TL-WR2543ND BRAND NAME: TP-LINK APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED: Jul. 25 ~ Aug. 1, 2012 TEST ITEM: MASS-PRODUCTION STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model no.: TL-WR2543ND) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Aug. 30, 2012 ( Celia Chen / Senior Specialist ) APPROVED BY : , DATE : Aug. 30, 2012 ( Ken Liu / Manager ) Report No.: SA120301C28 5 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA120301C28 6 Report Format Version 5.0.0 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 29.1 2 20 0.2563 1.00 5180-5240 11.6 3 20 0.0057 1.00 5745-5825 27.3 3 20 0.2132 1.00 --- END ---

Report No.: RF120301C28 1 of 97 Report Format Version 5.0.0 FCC (15.247) & CANADA RSS-210 (ANNEX 8) TEST REPORT REPORT NO.: RF120301C28 MODEL NO.: TL-WR2543ND FCC ID: TE7WR2543N IC: 8853A-WR2543N RECEIVED: Mar. 1, 2012 TESTED: Jul. 25 ~ Aug. 1, 2012 ISSUED: Aug. 30, 2012 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park,Shennan Rd, Nanshan, Shenzhen,China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF120301C28 2 of 97 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD................................................................................6 1. CERTIFICATION.............................................................................................7 2. SUMMARY OF TEST RESULTS.....................................................................8 2.1 MEASUREMENT UNCERTAINTY..................................................................8 3. GENERAL INFORMATION.............................................................................9 3.1 GENERAL DESCRIPTION OF EUT................................................................9 3.2 DESCRIPTION OF TEST MODES................................................................11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL................12 3.3 DESCRIPTION OF SUPPORT UNITS..........................................................16 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST...........................................16 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS...............................17 4. TEST TYPES AND RESULTS (FOR 2.4GHZ BAND)....................................18 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT........................18 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT.....18 4.1.2 TEST INSTRUMENTS..................................................................................19 4.1.3 TEST PROCEDURES...................................................................................20 4.1.4 DEVIATION FROM TEST STANDARD.........................................................20 4.1.5 TEST SETUP................................................................................................21 4.1.6 EUT OPERATING CONDITIONS..................................................................21 4.1.7 TEST RESULTS............................................................................................22 4.2 CONDUCTED EMISSION MEASUREMENT................................................35 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..............................35 4.2.2 TEST INSTRUMENTS..................................................................................35 4.2.3 TEST PROCEDURES...................................................................................36 4.2.4 DEVIATION FROM TEST STANDARD.........................................................36 4.2.5 TEST SETUP................................................................................................36 4.2.6 EUT OPERATING CONDITIONS..................................................................36 4.2.7 TEST RESULTS............................................................................................37 4.3 6DB BANDWIDTH MEASUREMENT............................................................39 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT.........................................39 4.3.2 TEST SETUP................................................................................................39 4.3.3 TEST INSTRUMENTS..................................................................................39 4.3.4 TEST PROCEDURE.....................................................................................39 4.3.5 DEVIATION FROM TEST STANDARD.........................................................39 4.3.6 EUT OPERATING CONDITIONS..................................................................39 4.3.7 TEST RESULTS............................................................................................40 4.4 OCCUPIED BANDWIDTH MEASUREMENT................................................44 4.4.1 TEST SETUP................................................................................................44 4.4.2 TEST INSTRUMENTS..................................................................................44 Report No.: RF120301C28 3 of 97 Report Format Version 5.0.0 4.4.3 TEST PROCEDURE..............…

Text truncated - open the document above for the full version.

Report No.:RF120301C28 1 of 2 Report Format Version 5.0.0 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.:RF120301C28 2 of 2 Report Format Version 5.0.0 RADIATED EMISSION TEST