TE7WR741NDV4150Mbps Wireless N Router

TL-WR740N TL-WR741ND 150Mbps Wireless N Router Rev: 3.0.0 1910010520 I COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ¾ Reorient or relocate the receiving antenna. ¾ Increase the separation between the equipment and receiver. ¾ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ¾ Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. II FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation None Only for indoor applications Note: Please don’t use the product outdoors in France. TP-LINK TECHNOLOGIES CO., LTD TP-LINK TECHNOLOGIES CO., LTD. South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan, Shenzhen, P. R. China DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N Router Model No.: TL-WR740N/TL-WR741ND Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.8.1:2008& ETSI EN 301 489-17 V2.1.1:2009 EN60950-1:2006 Recommendation 1999/519/EC EN62311:2008 Directives 2004/108/EC The above product is in conformity with the following standards or other normative documents EN 55022:2006 +A1:2007 EN 55024:1998+A1:2001+A2:2003 EN 61000-3-2:2006 EN 61000-3-3:1995+A1:2001+A2:2005 Directives 2006/95/EC The above product is in conformity with the following standards or other normative documents EN60950-1:2006 Directive（ErP） 2009/125/EC Audio/Video, information and communication technology equipment- Environmentally conscious design EN62075:2008 Person is responsible for marking this declaration: Yang Hongliang Product Manager of International Business TL-WR740N/TL-WR741ND150Mbps Wireless N Router I CONTENTS Package Contents ..........................................................................................................................1 Chapter 1. Introduction.................................................................................................................2 1.1 Overview of the Router.................................................................................................2 1.2 Conventions .................................................................................................…

Text truncated - open the document above for the full version.

[email protected] www.adt.com.tw TO: ALL CLIENTS Starting from August 19, 1996, products like PC and PC peripherals could use DoC method for marketing in United States. But the following documents should be prepared before shipping: 1. Test report – issued by NVLAP or A2LA accreditated laboratory. 2. Declaration of Conformity (DoC) Dorm – Should contain importers signature. 3. Original Design drawing (eg. Schematic and block diagram, Users Manual or Service Manual of product) 4. During production of units, the checking procedure should be described to guarantee that each unit of equipment marked under a DoC is identical to the unit tested or within variation that can be expected due to quantity production and testing on a statistical basis. 5. All modifications performed due to EMI should be recorded and tested if necessary. Note: ♦ Doc label should be stuck on the product. (See attachment) ♦ FCC statement should be included on the label as well as Users Manual. (The contents are same as that of FCC ID application) ♦ The responsible person signing the DoC form should take the responsibility that the sold products will have the same EMI characteristics as that of the tested sample and thus comply with the FCC limits. ♦ The above documents should be submitted to FCC during inspection within 14 days. If sample requested, the sample should be submitted to FCC within 60 days. The shipping charges will be bore by the DoC declarer. ♦ The above documents should be held by the responsible person signing the DoC. (附件一：FCC DoC Label 樣本) (For stand-alone test unit) (For unit assembled by modules with DoC) [email protected] www.adt.com.tw FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY (DoC) FOR THE FOLLOWING EQUIPMENT: PRODUCT NAME: 150Mbps Wireless N Router MODEL NO.: TL-WR740N / TL-WR741ND TRADE NAME: TP-LINK IS HEREWITH CONFIRMED AND FOUND TO COMPLY WITH THE REQUIREMENTS OF CFR 47 PART 15 REGULATION. THE RESULTS OF ELECTROMAGNETIC EMISSION EVALUATION ARE SHOWN IN THE REPORT NO.: FD111010C03, ISSUED ON Oct.25, 2011. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND, (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THE FOLLOWING MANUFACTURER/IMPORTER IS RESPONSIBLE FOR THIS DECLARATION： __________________________________________________________________ (COMPANY NAME) __________________________________________________________________ (COMPANY ADDRESS) TEL： _________________________ FAX：____________________________ __________________________________________________________________ (NAME) (TITLE) __________________________________________________________________ (SIGNATURE) (DATE)

Page 1 CONSTRUCTION PHOTOS OF EUT Model: TL-WR740N Page 2 Model: TL-WR741ND Page 3 Page 4 Page 5 Page 6

TL-WR740N(UN)4.0产品规格标 A1 80g艾利铜版纸+雾膜 美A-174 TL-WR740N(UN)4.0 2011-5-4 白色 PANTONE COOLGRAY 9C、白色 白色 PANTONE COOLGRAY 9C 赵娣 1 2 E D C B A 1 2 3 4 5 6 7 8 9 E D C 3 4 5 6 7 8 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 与上一版的区别 记 录 68.48*39mm, 6R PANTONE COOLGRAY 9C Model No.: Power: 150Mbps Wireless N Router 文字已转曲 FCC ID:TE7WR741NDV4 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Default Access: TL-WR741ND(UN)4.0产品规格标 A1 80g艾利铜版纸+雾膜 美A-174 TL-WR741ND(UN)4.0 2011-5-4 白色 PANTONE COOLGRAY 9C、白色 白色 PANTONE COOLGRAY 9C 赵娣 1 2 E D C B A 1 2 3 4 5 6 7 8 9 E D C 3 4 5 6 7 8 B A 9 料号： 设 计 审 核 颜 色 名 称 版 本 材 质 模 具 机型版本号 完成日期 logo 底色 文字 其它 与上一版的区别 记 录 68.48*39mm, 6R PANTONE COOLGRAY 9C Model No.: Power: 150Mbps Wireless N Router 文字已转曲 FCC ID:TE7WR741NDV4 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Default Access:

Label Location

Page 7 Model: TL-WR740N Page 8 Page 9 Page 10 Model: TL-WR741ND Page 11 Page 12 Page 13

FCC ID: TE7WR741NDV4 Report No.: RF111010C03 Operational Description This device is a 150Mbps Wireless N Router, which operates in 2.4GHz band; the maximum data rate could be up to 130Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 130Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered from 9Vdc power adapter. The antenna is dipole antenna with out antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No.: SA111010C03 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA111010C03 MODEL NO.: TL-WR740N, TL-WR741ND FCC ID: TE7WR741NDV4 RECEIVED: Oct. 10, 2011 TESTED: Oct. 21 ~ Nov. 25, 2011 ISSUED: Nov. 28, 2011 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 5 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval, or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA111010C03 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................. 4 2. RF EXPOSURE............................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE)......................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................... 5 2.3 CLASSIFICATION ........................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER.................................. 5 Report No.: SA111010C03 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Nov. 28, 2011 Report No.: SA111010C03 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT: 150Mbps Wireless N Router MODEL: TL-WR740N, TL-WR741ND BRAND: TP-LINK APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. TESTED: Oct. 21 ~ Nov. 25, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: TL-WR740N) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Nov. 28, 2011 Pettie Chen / Specialist APPROVED BY : , DATE :Nov. 28, 2011 Gary Chang / Technical Manager Report No.: SA111010C03 Report Format Version 4.0.0 5 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 24.1 5 20 0.162 1.00

Report No.: RF111010C03 1 Report Format Version 4.1.0 FCC TEST REPORT REPORT NO.: RF111010C03 MODEL NO.: TL-WR740N (Refer to item 3.1 for the more details) FCC ID: TE7WR741NDV4 RECEIVED: Oct. 10, 2011 TESTED: Oct. 21 ~ Nov. 25, 2011 ISSUED: Nov. 28, 2011 APPLICANT: TP-LINK TECHNOLOGIES CO., LTD. ADDRESS: Building 24 (floors 1,3,4,5) and 28 (floors1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan (R.O.C) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 53 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF111010C03 2 Report Format Version 4.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .........................................................................................................4 1. CERTIFICATION ...................................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................................... 6 3. GENERAL INFORMATION ...................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................ 7 3.2 DESCRIPTION OF TEST MODES .......................................................................................... 8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ..................................................................... 9 3.2.2 DESCRIPTION OF SUPPORT UNITS .................................................................................. 10 3.2.3 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................................ 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS....................................................... 13 4. TEST TYPES AND RESULTS................................................................................................ 14 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT................................................ 14 4.1.1 LIMITS OF RADIATED AND BANDEDGE EMISSION MEASUREMENT ............................. 14 4.1.2 TEST INSTRUMENTS ........................................................................................................... 15 4.1.3 TEST PROCEDURES............................................................................................................ 16 4.1.4 DEVIATION FROM TEST STANDARD.................................................................................. 16 4.1.5 TEST SETUP ........................................................................................................................ 17 4.1.6 EUT OPERATING CONDITIONS .......................................................................................... 17 4.1.7 TEST RESULTS................................................................................................................... .. 18 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................ 32 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT...................................................... 32 4.2.2 TEST INSTRUMENTS ........................................................................................................... 32 4.2.3 TEST PROCEDURES............................................................................................................ 33 4.2.4 DEVIATION FROM TEST STANDARD.................................................................................. 33 4.2.5 TEST SETUP ........................................................................................................................ 34 4.2.6 EUT OPERATING CONDITIONS .......................................................................................... 34 4.2.7 TEST RESULTS..................................................................................................................... 35 4.3 6dB BANDWIDTH MEASUREMENT ..................................................................................... 39 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................................. 39 4.3.2 TEST SETUP ........................................................................................................................ 39 4.3.3 TEST INSTRUMENTS ........................................................................................................... 39 4.3.4 TEST PROCEDURE .............................................................................................................. 39 4.3.5 DEVIATION FROM TEST STANDARD.................................................................................. 39 Report No.: RF111010C03 3 Report Format Version 4.1.0 4.3.6 EUT OPERATING CONDITIONS .......................................................................................... 39 4.3.7 TEST RESULTS..................................................................................................................... 40 4.4 CONDUCTED OUTPUT POWER.......................................................................................... 41 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT .......................................... 41 4.4.2 TEST SETUP .................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (Test Mode A) 2 CONDUCTED EMISSION TEST (Test Mode B) 3 RADIATED EMISSION TEST (Test Mode A) 4 RADIATED EMISSION TEST (Test Mode B)