TFJUIC681Contactless Card Reader

UIC681 Contactless Smart Card Reader Module -RS232 Interface- Programmer’s Manual Document #: PM063-U Revision 4 Oct. 5, 2006 UIC681 Programmer’s Manual UDN PM063-U Rev. 4 I NOTICE The issuer of this manual has made every effort to provide accurate information contained in this manual. The issuer shall not be held liable for any technical and editorial omissions or errors made herein; nor for incidental consequential damages resulting from the furnishing, performance or use of this material. This document contains proprietary information protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated without the prior written permission of the issuer. The information provided in this manual is subject to change without notice. AGENCY APPROVED - Specification for FCC Class B - Specification for UL/CUL - Specification for CE Class B, CISPR 22 Class B - Product Certificate by Taiwan BSMI (Bureau of Standards, Metrology and Inspection) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help. You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment. WARNING You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. WARRANTY This product is served under one-year warranty of defects in material and functionality to the original purchasers. Within the warranty period, if the product found to be defective will be repaired or replaced. This warranty applies to the products only under the normal use of the original purchasers, and in no circumstances covers incidental or consequential damages through consumers’ misuse or modification of the product. UIC681 Programmer’s Manual UDN PM063-U Rev. 4 II PREFACE This manual provides detailed information relating to the overall operational, electrical, mechanical, environmental and functional aspects of the UIC681. This document should be read and understood prior to initial operation of the product. For ease of installation and programming use, we have addressed everything from its attractive features to its various configurations. When designing the UIC681, we selected what we feel are the most useful features and functions. If in some cases you find that your specific needs differ from our existing products, we welcome your comments and suggestions. Custom-designed models are also available. If further questions do arise, please call for technical support, our FAE will assist you in any way we can. UIC681 Programmer’s Manual UDN PM063-U Rev. 4 III Table of Contents Section1 : General Description................................................................. 1-1 1.1 Features............................................................................................................. 1-1 1.2 Application ........................................................................................................ 1-1 1.3 Part Number Description ................................................................................. 1-2 Section2 : Configurations ......................................................................... 2-1 2.1 Dimensions of UIC681 PCBA........................................................................... 2-1 2.2 Dimensions of Remote Antenna PCBA........................................................... 2-1 2.3 Accessories of UIC681..................................................................................... 2-2 Section3 : Technical Specifications ......................................................... 3-1 3.1 Functional Specifications ................................................................................ 3-1 3.2 Mechanical Specifications ............................................................................... 3-1 Dimension............................................................................................................................. 3-1 3.3 Electrical Specifications................................................................................... 3-2 Power Required .................................................................................................................... 3-2 Power Consumption ............................................................................................................. 3-2 Communication..................................................................................................................... 3-2 Communication Signal (RS232) ........................................................................................... 3-2 3.4 Environmental Specifications.......................................................................... 3-2 Temperature.......................................................................................................................... 3-2 …

Text truncated - open the document above for the full version.

Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: TFJUIC681 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Complete Schematics of the Contactless Card Reader, Block Diagram, Circuit Description, The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Ivy Chang General Manager 1-510-438-6799 ext 11 Date: July. 13th 2006 Uniform Industrial Corp. 47709 Fremont Blvd., Fremont, CA 94538-6512. U.S.A.

Project No.: 0606133 Page 2 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-KM0FYASN-XXX Project No.: 0606133 Page 7 of 26 Neutron Engineering Inc. 0606133 Model UIC681-RM0FYDSE-XXX Project No.: 0606133 Page 8 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM0FYDSE-XXX Project No.: 0606133 Page 13 of 26 Neutron Engineering Inc. 0606133 0606133 Power adapter HAPU05F2 Project No.: 0606133 Page 14 of 26 Neutron Engineering Inc. 0606133 Power adapter HAPU05F2 Project No.: 0606133 Page 15 of 26 Neutron Engineering Inc. 0606133 Model UIC681-RM1FYDSC-XXX Project No.: 0606133 Page 16 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM1FYDSC-XXX Project No.: 0606133 Page 23 of 26 Neutron Engineering Inc. 0606133 0606133 Power adapter PA1010-050DUB Project No.: 0606133 Page 24 of 26 Neutron Engineering Inc. 0606133 Power adapter PA1010-050DUB Project No.: 0606133 Page 25 of 26 Neutron Engineering Inc. 0606133 0606133 Power adapter DCU050050 Project No.: 0606133 Page 26 of 26 Neutron Engineering Inc. 0606133 Power adapter DCU050050

Report No.: NEI-FCCP-1-0606133 Page 61 of 61 Neutron Engineering Inc. 6. PRODUCT LABELING -- FCC ID label -- The remained portion of label statement required by FCC is attached in the user’s manual. -- Location of Label on EUT -- 0.4 cm 2.2 cm

Project No.: 0606133 Page 3 of 26 Neutron Engineering Inc. 0606133 Model UIC681-KM0FYASN-XXX Project No.: 0606133 Page 4 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-KM0FYASN-XXX Project No.: 0606133 Page 5 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-KM0FYASN-XXX Project No.: 0606133 Page 6 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-KM0FYASN-XXX Project No.: 0606133 Page 9 of 26 Neutron Engineering Inc. 0606133 Model UIC681-RM0FYDSE-XXX Project No.: 0606133 Page 10 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM0FYDSE-XXX Project No.: 0606133 Page 11 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM0FYDSE-XXX Project No.: 0606133 Page 12 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM0FYDSE-XXX Project No.: 0606133 Page 17 of 26 Neutron Engineering Inc. 0606133 Model UIC681-RM1FYDSC-XXX Project No.: 0606133 Page 18 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM1FYDSC-XXX Project No.: 0606133 Page 19 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM1FYDSC-XXX Project No.: 0606133 Page 20 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM1FYDSC-XXX Project No.: 0606133 Page 21 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM1FYDSC-XXX Project No.: 0606133 Page 22 of 26 Neutron Engineering Inc. 0606133 0606133 Model UIC681-RM1FYDSC-XXX

Report No.: NEI-FCCP-1-0606133 Page 2 of 61 Neutron Engineering Inc. Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: NEI-FCCP-1-0606133 Page 3 of 61 Neutron Engineering Inc. Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 3.4 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION 13 4.1.2 MEASUREMENT INSTRUMENTS LIST 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 15 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 32 4.2.1 RADIATED EMISSION LIMITS 32 4.2.2 MEASUREMENT INSTRUMENTS LIST 33 4.2.3 TEST PROCEDURE 33 4.2.4 DEVIATION FROM TEST STANDARD 33 4.2.5 TEST SETUP 34 4.2.6 EUT OPERATING CONDITIONS 35 The EUT tested system was configured as the statements of 4.1.6 Unless otherwise a special operating condition is specified in the follows during the testing. 35 4.2.7 TEST RESULTS 36 4.2.8 TEST RESULTS 44 4.3 FREQUENCY STABILITY MEASUREMENT 48 4.3.1 FREQUENCY STABILITY LIMITS 48 4.3.2 MEASUREMENT INSTRUMENTS LIST 48 4.3.3 TEST PROCEDURE 48 4.3.4 DEVIATION FROM TEST STANDARD 48 4.3.5 EUT OPERATING CONDITIONS 48 4.3.6 TEST RESULTS 49 4.3.7 TEST RESULTS 51 Report No.: NEI-FCCP-1-0606133 Page 4 of 61 Neutron Engineering Inc. Table of Contents Page 4.3.8 TEST RESULTS 52 5 . EUT TEST PHOTO 53 6 . PRODUCT LABELING 61 Report No.: NEI-FCCP-1-0606133 Page 5 of 61 Neutron Engineering Inc. 1. CERTIFICATION E q u i p m e n t : Contactless Card Reader Trade Name : Uniform M o d e l N o . : UIC681 Series A p p l i c a n t : Uniform Industrial Corp. Data of Test : Jul. 14, 2006 ~ Oct. 26, 2006 Te s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C / RSS-210: 2004/ ANCI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-0606133) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and CNLA according to the ISO-17025 quality assessment standard and technical standard(s). Report No.: NEI-FCCP-1-0606133 Page 6 of 61 Neutron Engineering Inc. 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: (Antenna to EUT distance is 3 m) FCC Part15, Subpart C Standard Test Item Judgment 15.207 Conducted Emission PASS 15.35 / 15.205 / 15.209 / 15.225 Radiated Emission PASS 15.225(e) Frequency Stability PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Report No.: NEI-FCCP-1-0606133 Page 7 of 61 Neutron Engineering Inc. 2.1 TEST FACILITY The test facilities used to collect the test data in this report is OS02 at the location of No.132-1, Lane 329, Sec. 2, Palain Road, Shijr City, Taipei, Taiwan. 2.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 A. Conducted Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE C01 ANSI150 KHz ~ 30MHz 1.94 B. Radiated Measurement : Test Site Method Measurement Frequency Range Ant. H / V U，(dB) NOTE OS-01 ANSI30MHz ~ 200MHz V 3.82 30MHz ~ 200MHz H 3.60 200MHz ~ 1,000MHz V 3.86 200MHz ~ 1,000MHz H 3.94 OS-02 ANSI30MHz ~ 200MHz V 2.48 30MHz ~ 200MHz H 2.16 200MHz ~ 1,000MHz V 2.50 200MHz ~ 1,000MHz H 2.66 Report No.: NEI-FCCP-1-0606133 Page 8 of 61 Neutron Engineering Inc. 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment Contactless Card Reader Trade Name Uniform Model No. UIC681 Series OEM Brand/Model No. N/A Model Difference Please refer to next page the Part Number Description of UIC681 Series. All the models were tested, and the model: UIC681-KM0FYASN-XXX, UIC681-RM0FYDSE-XXX, and UIC681-RM1FYDSC-XXX were found to be the worst case during the pr-scanning test. These models of the worst case were used for final testing and collecting test data included in this report. Product Description The EUT is a Contactless Card Reader. A. Operation Frequency 13.56 MHz B. Modulation Type FSK C. Antenna Designation Integral A…

Text truncated - open the document above for the full version.

Report No.: NEI-FCCP-1-0606133 Page 53 of 61 Neutron Engineering Inc. 5. EUT TEST PHOTO Conducted Measurement Photos Model UIC681-KM0FYASN-XXX without power adapter Report No.: NEI-FCCP-1-0606133 Page 54 of 61 Neutron Engineering Inc. Conducted Measurement Photos Model UIC681-RM0FYDSE-XXX with power adapter HAPU05F2 Report No.: NEI-FCCP-1-0606133 Page 55 of 61 Neutron Engineering Inc. Conducted Measurement Photos Model UIC681-RM1FYDSC-XXX with power adapter PA1010-050DUB Report No.: NEI-FCCP-1-0606133 Page 56 of 61 Neutron Engineering Inc. Conducted Measurement Photos Model UIC681-RM1FYDSC-XXX with power adapter DCU050050 Report No.: NEI-FCCP-1-0606133 Page 57 of 61 Neutron Engineering Inc. Radiated Measurement Photos Model UIC681-KM0FYASN-XXX without power adapter Report No.: NEI-FCCP-1-0606133 Page 58 of 61 Neutron Engineering Inc. Radiated Measurement Photos Model UIC681-RM0FYDSE-XXX with power adapter HAPU05F2 Report No.: NEI-FCCP-1-0606133 Page 59 of 61 Neutron Engineering Inc. Radiated Measurement Photos Model UIC681-RM1FYDSC-XXX with power adapter PA1010-050DUB Report No.: NEI-FCCP-1-0606133 Page 60 of 61 Neutron Engineering Inc. Radiated Measurement Photos Model UIC681-RM1FYDSC-XXX with power adapter DCU050050