TLZ-BT076Bluetooth Module

Azurewave / AW-BT076 Bluetooth Module User Manual 1 Install the Bluetooth Driver..................................................2 Connect to other Bluetooth Enabled Devices..........................7 Uninstall the Bluetooth Driver..............................................11 2 Install the Bluetooth Driver Step1：Double click CSR Bluetooth Software 3 Step2 ：Choose 『I accept the terms in the license agreement』 4 Step3：Double click 『Next』 5 Step4：Choose『Install』 6 Step5：Install finish 7 Connect to other Bluetooth Enable Device Step1: Search new Bluetooth devices. 8 Step2 : Double click 『Next』 9 Step3 : Double click 『Next』 10 Step4: 11 Uninstalling the Bluetooth Driver Step1: 12 Step2: 13 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 14 This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna, As long as 1 condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: TLZ-BT252”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 15 For Taiwan警語  經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性及功能。  低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立 即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線 電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之 干擾。 Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於平台上標示「本產品內含射頻模組: CCXXxxYYyyyZzW」字樣 16 Canadian Regulatory Wireless Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC ID: 6100A-AWBT252”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this R…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 1 Rev 2.0 SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw 8/9/2011 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, SPORTON International Inc. hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): Product Name: Bluetooth Module Model Number: AW-BT076 FCC ID: TLZ-BT076 We affirm that between SIEMIC and SPORTON International Inc., any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Signature: Name / title: Wayne Hsu / Vice Manager Contact information / address: No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. / Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw

FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A1 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255 APPENDIX B. Photographs of EUT FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A2 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A3 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A4 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255

FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A1 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255 APPENDIX B. Photographs of EUT FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A2 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A3 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : A4 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 23, 2011 FAX : 886-2-2696-2255

RF Exposure Evaluation Evaluate for portable condition. output < 60/f(GHz) mW, SAR evaluation is generally not required Operating Frequency (GHz) Output Power (dBm) Output Power (mW) 60/f(GHz) 2.4 1.49 1.409 25 output < 60/f(GHz) mW 1.409mW< 25mW Thus No SAR is required for Portable used condition Page No. : 2 of 2 FCC ID : TLZ-BT076 FCC TEST REPORT Report No. : FR122348 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) = d GP30 Power Density: Pd (W/m²) = 377 2 E E = Electric field (V/m) P = Peak RF output power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = 2 377 30 d GP   From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. 1.3. Calculated Result and Limit Antenna Type : Printed Antenna Max Conducted Power for Bluetooth: 1.49dBm Test Mode Min. User Distance (cm) Gain (dBi)Numeric Gain Conducted Power (dBm) Conducted Power (mW) Power Density (mW/cm2) 2.4G 20 2 1.584893 1.87 1.5382 0.0031

SPORTON International Inc. Report Format Version: a FCC TEST REPORT Report No. : FR122348 FCC RADIO TEST REPORT according to 47 CFR FCC Part 15 Subpart C § 15.247 Equipment :Bluetooth Module Model No. :AW-BT076 Brand Name :AzureWave Filing Type : New Application Applicant Manufacturer :AzureWave Technologies, Inc. 8F, No.94, Baozhong Rd., Xindian, Taipei, Taiwan 231. FCC ID :TLZ-BT076 Received Date :Mar. 10, 2011 Final Test Date :Mar. 15, 2011 Statement Test result included is only for the Bluetooth part of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. SPORTON International Inc. No.52 Hwa Ya 1 st Rd, Hwa Ya Technology Park, Kwei-Shan Hsiang, Taoyuan Hsien, Taiwan, R.O.C. SPORTON International Inc. Page No. : i of ii TEL : 886-2-2696-2468 Issued Date : Mar. 23, 2011 FAX : 886-2-2696-2255 FCC ID : TLZ-BT076 FCC TEST REPORT Report No. : FR122348 Table of Contents 1 SUMMARY OF THE TEST RESULT ....................................................................................................................... 2 2 GENERAL INFORMATION ...................................................................................................................................... 3 2.1 Product Details .........................................................................................................................................................................................3 2.2 Table for Filed Antenna ............................................................................................................................................................................3 2.3 Table for Carrier Frequencies ..................................................................................................................................................................3 2.4 Table for Test Modes ...............................................................................................................................................................................3 2.5 Table for Testing Locations ......................................................................................................................................................................4 2.6 Table for Supporting Units .......................................................................................................................................................................4 2.7 Table for Parameters of Test Software Setting ........................................................................................................................................4 2.8 EUT Operation during Test ......................................................................................................................................................................4 2.9 Test Configurations ..................................................................................................................................................................................5 3 TEST RESULT ......................................................................................................................................................... 6 3.1 AC Power Line Conducted Emissions Measurement ..............................................................................................................................6 3.2 Peak Output Power Measurement .........................................................................................................................................................10 3.3 Hopping Channel Separation Measurement ..........................................................................................................................................12 3.4 Number of Hopping Frequency Measurement .......................................................................................................................................17 3.5 Dwell Time Measurement ......................................................................................................................................................................19 3.6 Radiated Emissions Measurement ........................................................................................................................................................26 3.7 Band Edge and Fundamental Emissions Measurement ........................................................................................................................38 3.8 Antenna Requirements ..........................................................................................................................................................................43 4 LIST OF MEASURING EQUIPMENTS .................................................................................................................. 44 5 TEST LOCATION ................................................................................................................................................... 46 6 TAF CERTIFICATE OF ACCREDITATION ........................................................................................................... 47 APPENDIX A. TEST PHOTOS ........................................................................................................................ A1 ~ A7 APPENDIX B. PHOTOGRAPHS OF EUT ....................................................................................................... B1 ~ B4 SPORTON International Inc. Page No. : ii of ii TEL : 886-2-2696-2468 Issued Date : Mar. 23, 2011 FAX : 886-2-2696-2255 FCC ID : TLZ-BT076 FCC TE…

Text truncated - open the document above for the full version.

Page No. : A1 of A7 FCC ID : TLZ-BT076 F FCC TEST REPORT Report No. : FR122348 Appendix A. Test Photos Page No. : A2 of A7 FCC ID : TLZ-BT076 F FCC TEST REPORT Report No. : FR122348 1 Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Page No. : A3 of A7 FCC ID : TLZ-BT076 F FCC TEST REPORT Report No. : FR122348 SIDE VIEW Page No. : A4 of A7 FCC ID : TLZ-BT076 F FCC TEST REPORT Report No. : FR122348 2 Photographs of Radiated Emissions Test Configuration For radiated emissions 9kHz~30MHz FRONT VIEW REAR VIEW Page No. : A5 of A7 FCC ID : TLZ-BT076 F FCC TEST REPORT Report No. : FR122348 For radiated emissions 30MHz~1GHz FRONT VIEW REAR VIEW Page No. : A6 of A7 FCC ID : TLZ-BT076 F FCC TEST REPORT Report No. : FR122348 For radiated emissions above 1GHz FRONT VIEW REAR VIEW Page No. : A7 of A7 FCC ID : TLZ-BT076 F FCC TEST REPORT Report No. : FR122348 EUT take a close-up. FRONT VIEW REAR VIEW