TLZ-CU282IEEE 802.11 b/g/n Smart Energy Module

- 1 - AW-CU282 Wireless LAN Module IC MFG Tool Command User Guide Version 0.1 Document release Date Modification Initials Approved Ver. 0.1 2013/3/17Initial version Renton Tao Ivan Chen - 2 - Step1: Initial Command As the information showed on your screen, please enter these commands below to start your test. Command: 1 Wi-Fi testing mode Step2: Generate 802.11 b/g/n Packet (1)Command: 22 1 12 1 22: Initial transmit power in the antenna 1: Set the wanted channel (1~14 for B/G/N mode) 12: Set the wanted power, typically G mode: 12 dBm/ B mode: 15 dBm 1: Set the mode, 1G mode & N mode , 0 B mode (2)Command: 112 0 (only for N mode) 112: N mode HT20/40. 0: for HT20/40. 0HT20, 1HT40 (3)Command: 25 1 13 25: Set duty cycle, packet mode. 1: Data rate enable 13: Data rate set up A mode &B mode & G mode 1Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 1 3 4 6 7 8 9 10 36Mbps 48Mbps54Mbps 11 12 13 N mode MCS0 MCS1MCS2MCS3MCS4MCS5MCS6MCS7MCS8 15 16 17 18 19 20 21 22 23 After you type above command, you can measure the 802.11b/g/n packet by your RF test instrument (exp: Agilent 4010, IQview...). (4) Command: 25 0 Stop transmitting packet signal. - 3 - Step3: Generate 802.11b/g/n continuous symbol (1)Please re-type the Step5 (1)~(4) commands. (2)Command 17 1 13 17: Set continuous mode. 1: Enable data rate 13: 54 Mbps, other data rate, please refer the above table. After you type above command, you can measure the 802.11b/g continuous symbol in your RF test instrument. (3)Command 17 0 Stop transmitting continuous signal Step4: Test RX sensitivity Before test RX, the Marvell standard waveform is needed. Please contact Azurewave FAE for this issue. (1) Command 12 1 12: Choose RX text channel 1: Channel number, (1~14 for B/G/N mode) (2) Command: 112 0 (only for N mode) 112: N mode HT20/40. 0: for HT20/40. 0HT20, 1HT40 (3) 32: Check the received packets. (4) 31:Clear all the received packets. Step5: Others Commands (1) Command 45 Check the MAC (2) Command 99 Quit the test mode/ Quit the MFG tool Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) Module approval valid only when the module is installed in the tested host or compatible series of host As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: TLZ-CU282”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 2

FCC ID: TLZ-CU282 Report No.: RF130403E09 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch May 2, 2013 Dear Application Examiner, AzureWave Technologies, Inc., It’s an IEEE 802.11 b/g/n Smart Energy Module, FCC ID: TLZ-CU282 would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip 88W8782. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is 88MC200. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Hank Chung Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Report No.: 130403E09 1 of 3 CONSTRUCTION PHOTOS OF EUT Report No.: 130403E09 3 of 3

FCC ID: TLZ-CU282 Model: AW-CU282 IEEE 802.11 b/g/n Smart Energy Module 20mm 10mm (Fig. 1) FCC ID: TLZ-CU282 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Report No.: 130403E09 2 of 3

Report No.: SA130403E09 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130403E09 MODEL NO.: AW-CU282 FCC ID: TLZ-CU282 RECEIVED: Apr. 03, 2013 TESTED: Apr. 13, 2013 ISSUED: Apr. 24, 2013 APPLICANT: AzureWave Technologies, Inc. ADDRESS: 8 F., No. 94, Baozhong Rd., Xindian,Taipei, Taiwan 231 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA130403E09 2 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 6 Report No.: SA130403E09 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130403E09 Original release Apr. 24, 2013 Report No.: SA130403E09 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: IEEE 802.11 b/g/n Smart Energy Module BRAND NAME: AzureWave MODEL NO.: AW-CU282 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: AzureWave Technologies, Inc. TESTED DATE: Apr. 13, 2013 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: AW-CU282) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Jan. 14, 2013 ( Lori Chung, Specialist ) APPROVED BY : , DATE: Jan. 14, 2013 ( May Chen, Manager ) Report No.: SA130403E09 5 of 6 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA130403E09 6 of 6 Report Format Version 5.0.0 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 299.226 0.53 20 0.06726 1 --- END --- CONCLUSION: Both of the 2.4GHz and 5GHz WLAN can transmit simultaneously, the formula of calculated the MPE is: CPD 1 / LPD 1 + CPD 2 / LPD 2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density Therefore, the worst-case situation is 0.12256 / 1 + 0.42671 / 1 = 0.549, which is less than “1”. This confirmed that the device comply with FCC 1.1310 MPE limit.

Report No.: RF130403E09 1 of 54 Report Format Version 5.1.1 FCC TEST REPORT REPORT NO.: RF130403E09 MODEL NO.: AW-CU282 FCC ID: TLZ-CU282 RECEIVED: Apr. 03, 2013 TESTED: Apr. 09 to 15, 2013 ISSUED: Apr. 24, 2013 APPLICANT: AzureWave Technologies, Inc. ADDRESS: 8 F., No. 94, Baozhong Rd., Xindian,Taipei, Taiwan 231 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF130403E09 2 of 54 Report Format Version 5.1.1 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 4 1. CERTIFICATION ..................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 7 3. GENERAL INFORMATION ..................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ........................................................................ 8 3.2 DESCRIPTION OF TEST MODES........................................................................ 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 14 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................. 15 3.5 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 15 4. TEST TYPES AND RESULTS ............................................................................... 16 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 16 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 16 4.1.2 TEST INSTRUMENTS .......................................................................................... 16 4.1.3 TEST PROCEDURES........................................................................................... 17 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 17 4.1.5 TEST SETUP ........................................................................................................ 17 4.1.6 EUT OPERATING CONDITIONS .......................................................................... 18 4.1.7 TEST RESULTS ................................................................................................... 19 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 21 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 21 4.2.2 TEST INSTRUMENTS .......................................................................................... 22 4.2.3 TEST PROCEDURES........................................................................................... 23 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 23 4.2.5 TEST SETUP ........................................................................................................ 24 4.2.6 EUT OPERATING CONDITIONS .......................................................................... 24 4.2.7 TEST RESULTS ................................................................................................... 25 4.3 6DB BANDWIDTH MEASUREMENT .................................................................... 38 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT.................................................. 38 4.3.2 TEST INSTRUMENTS .......................................................................................... 38 4.3.3 TEST PROCEDURE ............................................................................................. 38 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 38 4.3.5 TEST SETUP ........................................................................................................ 38 4.3.6 EUT OPERATING CONDITIONS .......................................................................... …

Text truncated - open the document above for the full version.

Report No.: 120702E04 1 of 3 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 120702E04 2 of 3 RADIATED EMISSION TEST Report No.: 120702E04 3 of 3