TLZ-CU288IEEE 802.11b/g/n Smart Energy Module

AW-CU288 EVB I1 User Guide V0.3 2014/07/14 Kai. Wu Confidential Relative Software ᒳᇆׂᐙދ 2 Application Software ‡ FTDI VCP Drivers (FT2232D) ‡ Libusb-win32-bin-1.2.6.0 ‡ Cygwin Set-up Procedure 1. Download FTDI VCP Drivers (FT2232D) 2. Download Libusb-win32-bin-1.2.6.0 3. Set Up CU28 8 EVB for Windows 4. Install FTDI VCP Drivers 5. Install Libusb-win32-bin-1.2.6.0 6. Install Cygwin ,QVHUWILOH³2SHQ2&']LS ́ By wmsdk_bundle-2.13.78) 8. Burning MCU Image with normal firmware 9. Run WIFI Normal Driver 10. Burning MCU Imag e with MFG firmware 11. Run WIFI MFG tool Confidential 1. Download FTDI VCP Drivers (FT2232D) ᒳᇆׂᐙދ 3 ,QVWDOOWKHGULYHUPDQXDOO\<RX FDQJHWWKHGULYHUIURP)7',¶V ZHEVLWH http://www.ftdichip.com/Drivers/VCP.htm Confidential 2. Download Libusb-win32 ᒳᇆׂᐙދ 4 You can get the driver from libusb- ZLQ¶VZHEVLWH http://sourceforge.net/proje cts/libusb-win32 Confidential 3. Set Up CU288 EVB for Windows ᒳᇆׂᐙދ 5 The USB port connects the CU288 evaluation board to the PC. ANT2 ANT1 Confidential 4-1. Install FTDI VCP Drivers ᒳᇆׂᐙދ 6 DONE Confidential 4-2. Install FTDI VCP Drivers ᒳᇆׂᐙދ 7 Verifying Driver Installation: To verify that driver install ation has completed successfully, you can open the ³ 'HYLFH0DQDJHU ́ ULJKW -click My Computer, select Properties). In the System Properties windows, selec t Hardware, Device Manager. 7ZR³ 86%6HULDO3RUW ́VKRXOGEHOLVWHGXQGHU0< -PC\Ports (COM & LPT) Confidential 5-1. Install Libusb-win32 ᒳᇆׂᐙދ 8 Install inf-wizard: USB Serial Converter A (Interface 0) Confidential 5-2. Install Libusb-win32 ᒳᇆׂᐙދ 9 Verifying Driver Installation: To verify that driver install ation has completed successfully, you can open the ³ 'HYLFH0DQDJHU ́ ULJKW -click My Computer, select Properties). In the System Properties windows, selec t Hardware, Device Manager. One ³ USB Serial &RQYHUWHU$ ́ should be listed under MY-PC\Ports (lib usb- win32 devices) DONE Confidential 6-1. Install Cygwin ᒳᇆׂᐙދ 10 Install Cygwin: 1. Install Cygwin from: http://www.cygwin.co m/setup_x86.exe (for x86 32-bit systems) or http://www.cygwin.com/setup_x86_64.exe (for x86 64-bit systems) 2. Select the option Install from Internet 3. Use default installation path: c:\cygwin. If you chose an alternate instal lation directory, please make sure that there are no spaces in the path. 4. Pick the Local Package Director y (this is the download cache directory) 5. Select the option Direct Connection 6. Select any mirror you want to use 7. Add additional packages to the default selection: &OLFN³1H[W ́7KH Cygwin Setup window will show the progress as each package gets installed. Note: If you are not familiar with cygwin, plea se visit http://cygwin.com/ for additional information and details. In particular, the Cygwin User Guide (http://cygwin.com/cygwin-ug-net/) is a good resource for new users. Confidential 6-2. Install Cygwin ᒳᇆׂᐙދ 11 DONE Confidential 7- ,QVHUWILOH³2SHQ2&']LS ́ ᒳᇆׂᐙދ 12 8Q]LS³&8B2SHQ2&']LS ́DQGSXW ³UHDGHOIH[H ́WR& \cygwin\bin Confidential ᒳᇆׂᐙދ 13 8Q]LS³&8B2SHQ2&']LS ́DQGSXWWKHPWR& \cygwin\ 7- ,QVHUWILOH³2SHQ2&']LS ́ Confidential ᒳᇆׂᐙދ 14 Process C:\cygwin\Cygwin.bat 7- ,QVHUWILOH³2SHQ2&']LS ́ Confidential ᒳᇆׂᐙދ 15 Key in command : cd /cygdrive/c/cygwin/OpenOCD 7- ,QVHUWILOH³2SHQ2&']LS ́ Confidential 8-1. Burning Normal F/W ᒳᇆׂᐙދ 16 Check config8801.txt, layout.txt « files in OpenOCD folder Check files name Confidential 8-2. Burning Normal F/W ᒳᇆׂᐙދ 17 Key in command : ./flashprog.sh -l layout.txt -b config8801.txt Confidential ᒳᇆׂᐙދ 18 Burning information print as followed: Note : Please restart DUT after burning (Plug- in and Plug-out USB) 8-3. Burning Normal F/W Confidential 9-1. Run normal F/W ᒳᇆׂᐙދ 19 Open OS terminal and set USB comport (reference to page9 ), set baud- rate as 115200 off off 115200 Confidential ᒳᇆׂᐙދ 20 That will scan around AP 9-2. Run normal F/W EX: wlan-scan Enter help on the screen to see a ful l list of commands available for use Confidential 10-1. Burning MFG F/W ᒳᇆׂᐙދ 21 Check config8801_mfg.txt, layout.txt «ILOHV in OpenOCD folder Check files name Confidential ᒳᇆׂᐙދ 22 Command : ./flashprog.sh ± l layout.txt ± b config8801_mfg.txt 10-2. Burning MFG F/W Confidential ᒳᇆׂᐙދ 23 Burning information print as followed: Note : Please restart DUT after burning (Plug-in and Plug-out USB) 10-3. Burning MFG F/W Confidential Set USB comport Run Marvel 88w8801 MFG tool 11-1. Run Marvel 88w8801 WIFI MFG tool Confidential 11-2. Run Marvel 88w8801 WIFI MFG tool ᒳᇆׂᐙދ 25 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not exp…

Text truncated - open the document above for the full version.

FCC ID: TLZ-CU288 Report No.: RF140620E01 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch August 8, 2014 Dear Application Examiner, AzureWave Technologies, Inc., IEEE 802.11b/g/n Smart Energy Module, FCC ID: TLZ-CU288, would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip 88W8801. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is 88W8801. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Hank Chung Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Report No.: 140620E01 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 140620E01 Page 2 Antenna: ANT3216LL00R2400A Report No.: 140620E01 Page 3 Antenna: NanoBlue-IP04 Report No.: 140620E01 Page 4 Report No.: 140620E01 Page 5 Antenna: MS-A4008-25GC1-A1 Report No.: 140620E01 Page 6 Report No.: 140620E01 Page 7 Antenna: EDA_1313_2G4C1-A16

FCC ID： TLZ-CU288 LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label Here

Report No.: 140620E01 Page 1 CONSTRUCTION PHOTOS OF EUT

Report No.: SA140620E01 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA140620E01 MODEL NO.: AW-CU288 FCC ID: TLZ-CU288 RECEIVED: June 20, 2014 TESTED: July 10, 2014 ISSUED: Aug. 07, 2014 APPLICANT: AzureWave Technologies, Inc. ADDRESS: 8 F., No. 94, Baozhong Rd., Xindian,Taipei, Taiwan 231 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA140620E01 2 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. ANTENNA GAIN....................................................................................................... 5 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 6 Report No.: SA140620E01 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140620E01 Original release Aug. 07, 2014 Report No.: SA140620E01 5 of 6 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 5. ANTENNA GAIN The antennas provided to the EUT, please refer to the following table: No. Antenna Brand Model Gain (dBi) include cable loss Frequency range (MHz to MHz) Antenna Type Connecter Type Cable Length (mm) 1 Internal AzureWave ANT3216LL00 R2400A 3.17 2400-2500 CHIP NA NA 2 External NanoBlue NanoBlue-IP04 2 2400-2500 Monopole I-PEX 100 3 External MAG.LAYERS MS-A4008-25G C1-A1 2.98 2400-2500 PIFA I-PEX 150 4 External MAG.LAYERS EDA_1313_2G 4C1-A16 2.03 2400-2500 Dipole I-PEX 150 Report No.: SA140620E01 6 of 6 Report Format Version 5.0.0 6. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For WLAN FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2472 176.604 3.17 20 0.07290 1.00 --- END ---

Report No.: RF140620E01 1 of 84 Report Format Version 5.2.1 FCC TEST REPORT (15.247) REPORT NO.: RF140620E01 MODEL NO.: AW-CU288 FCC ID: TLZ-CU288 RECEIVED: June 20, 2014 TESTED: June 20 to July 14, 2014 ISSUED: Aug. 07, 2014 APPLICANT: AzureWave Technologies, Inc. ADDRESS: 8 F., No. 94, Baozhong Rd., Xindian,Taipei, Taiwan 231 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF140620E01 2 of 84 Report Format Version 5.2.1 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 4 1. CERTIFICATION .................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 7 3. GENERAL INFORMATION ..................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ....................................................................... 8 3.2 DESCRIPTION OF TEST MODES ....................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 14 3.4 DUTY CYCLE OF TEST SIGNAL ......................................................................... 15 3.5 DESCRIPTION OF SUPPORT UNITS .................................................................. 16 3.6 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 16 4. TEST TYPES AND RESULTS .............................................................................. 17 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 17 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 17 4.1.2 TEST INSTRUMENTS .......................................................................................... 17 4.1.3 TEST PROCEDURES .......................................................................................... 18 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 18 4.1.5 TEST SETUP ....................................................................................................... 18 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 19 4.1.7 TEST RESULTS ................................................................................................... 20 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 22 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 22 4.2.2 TEST INSTRUMENTS .......................................................................................... 23 4.2.3 TEST PROCEDURES .......................................................................................... 25 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 25 4.2.5 TEST SETUP ....................................................................................................... 26 4.2.6 EUT OPERATING CONDITIONS ......................................................................... 26 4.2.7 TEST RESULTS (MODE 1) .................................................................................. 27 4.2.8 TEST RESULTS (MODE 2) .................................................................................. 37 4.2.9 TEST RESULTS (MODE 3) .................................................................................. 47 4.2.10 TEST RESULTS (MODE 4) .................................................................................. 57 4.3 6DB BANDWIDTH MEASUREMENT ................................................................... 67 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ................................................. 67 4.3.2 TEST INSTRUMENTS .......................................................................................... 67 4.3.3 T…

Text truncated - open the document above for the full version.

Report No.: 140609E04 1 of 14 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 140609E04 2 of 14 RADIATED EMISSION TEST (Below 1GHz, CHIP antenna) Report No.: 140609E04 3 of 14 Report No.: 140609E04 4 of 14 RADIATED EMISSION TEST (Above 1GHz, CHIP antenna) Report No.: 140609E04 5 of 14 Report No.: 140609E04 6 of 14 RADIATED EMISSION TEST (Below 1GHz, Monopole antenna) Report No.: 140609E04 7 of 14 RADIATED EMISSION TEST (Above 1GHz, Monopole antenna) Report No.: 140609E04 8 of 14 Report No.: 140609E04 9 of 14 RADIATED EMISSION TEST (Below 1GHz, PIFA antenna) Report No.: 140609E04 10 of 14 RADIATED EMISSION TEST (Above 1GHz, PIFA antenna) Report No.: 140609E04 11 of 14 Report No.: 140609E04 12 of 14 RADIATED EMISSION TEST (Below 1GHz, Dipole antenna) Report No.: 140609E04 13 of 14 RADIATED EMISSION TEST (Above 1GHz, Dipole antenna) Report No.: 140609E04 14 of 14