TXT-F034K69P01Wireless Hand Controller

LMPL 2 0 L M P L 2 0 LMP L20 m S E L 00.000 6 + LMPL20 Pipe Laser Model 59-LMPL20 INSTRUCTION MANUAL Electronic Self-Leveling 2 • LMPL20 LMPL20 • 3 Fig. 1 Fig. 2 Fig. 3 LMPL20LMPL20LMPL20 m SEL Lock Line control / A B 00.000 6 + F D2 C D1 E2 E1 2 3 4 58 L MPL 20 L M P L 2 0 LM P L2 0 m SEL 10 2 1 3 4 567 9 8 10 00 . 000 6 + 4 • LMPL20 XY * * * ABC... XY * * * 00.000 6 + PHONE ABCDEF G IHJKL NAME A CI Y S TAT E DDRESS a b c d e f g T XXXXXXXXXXXX Fig. 4 Fig. 5 Fig. 6 Fig. 8 Fig. 7 Fig. 9 Fig. 10 X=353 510 10 234567 98 **** 000 9 Fig. 11 CHANGE RESET SECURITY CHANGE RESET SECURITY Fig. 12 XY * * * ABC... XY * * * GRADE UNITS Fig. 13 XY * * * ABC... XY * * * SECURITY Fig. 14 LMPL20 • 5 A E D B F D E C RC20 Fig. 15 Remote a b c d Fig. 18 Fig. 19 00.000 + 00.000 + a b Fig. 16 Fig. 17 Fig. 20 Fig. 21 Fig. 22 000 9 Thank you for purchasing the CST/Berger LMPL20 Electronic Self-Leveling Pipe Laser level. The LMPL20 pipe laser tool has many unique features such as a High Powered Red laser beam, which makes accurately locating the center of the beam easy. The Unique High Powered Red Laser beam also increases the visibility of the laser over long distances- inside or outside the pipe. Note: Please read this manual thoroughly before operation MODEL 59-LMPL20Pipe Laser, 12 VDC Ext. Power Cable, NiMH Battery Charger, NiMH Battery Pack, Alkaline Battery Pack, Small Target, Large Target, Target Holder, Carrying Case, Leg Set, Remote Control RC20, Instruction Manual, Warranty Card. Copyright © 2009 Robert Bosch Tool Corporation, All rights reserved. The information contained herein is proprietary information of Robert Bosch Tool Corporation and is subject to change without notice. This document shall not be copied or otherwise reproduced without Robert Bosch Tool Corporation’s written consent. SAFE OPERATING PROCEDURES CAUTION:Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure WARNING:Be sure to read and understand all instructions in this manual before using this product. Failure to follow all instructions may result in hazardous radiation exposure, electric shock, fire, and/or bodily injury. CAUTION:Use of controls or adjustments or performance of procedures other than those specified in this manual, may result in hazardous radiation exposure. CAUTION:The use of optical instruments with this product will increase eye hazard. IMPORTANT: The following labels are on your LMPL20 for your convenience and safety. They indicate where the laser light is emitted by the level. ALWAYS BE AWARE of their location when using the level. ALWAYSmake sure that any bystanders in the vicinity of use are made aware of the dangers of looking directly into the pipe laser tool . DO NOTremove or deface any warning or caution labels. Removing labels increases the risk of exposure to laser radiation. DO NOT stare directly at the laser beam or project the laser beam directly into the eyes of others. Serious eye injury could result. DO NOTplace the pipe laser tool in a position that may cause anyone to stare into the laser beam intentionally or unintentionally. Serious eye injury could result. DO NOTuse any optical instruments such as, but not limited to, telescopes or transits to view the laser beam. Serious eye injury could result. ALWAYSremove the batteries when cleaning the laser light aperture or laser lens. DO NOToperate the pipe laser tool around children or allow children to operate the pipe laser tool . Serious eye injury could result. ALWAYSturn the pipe laser tool "OFF" when not in use. Leaving the pipe laser tool "ON" increases the risk of someone inadvertently staring into the laser beam. EN 6 • LMPL20 ACCORDING TO IEC/EN 60825-1: 2007 DO NOToperate the pipe laser tool in combustible areas such as in the presence of flammable liquids, gases or dust. ALWAYSposition the pipe laser tool securely. Damage to the pipe laser tool and/or serious injury to the user could result if the pipe laser tool falls. ALWAYS use only the accessories that are recommended by the manufacturer of your pipe laser tool . Use of accessories that have been designed for use with other pipe laser tool s could result in serious injury. DO NOTuse this pipe laser tool for any purpose other than those outlined in this manual. This could result in serious injury. DO NOT leave pipe laser tool "ON" unattended in any operating mode. ALWAYSrepair and servicing must be performed by a qualified repair facility. Repairs performed by unqualified personnel could result in serious injury. DO NOTdisassemble the pipe laser tool . There are no user serviceable parts inside. Disassembling the laser will void all warranties on the product. Do not modify the product in any way. Modifying the pipe laser tool may result in hazardous laser radiation exposure. ELECTRICAL SAFETY PROCEDURES WARNING: Batteries can explode or leak, and can cause injury or fire. To reduce this risk: ALWAYSfollow all instructions and warnings on the battery label and package. DO NOTshort any battery terminals. DO NOTcharge alkaline batteries. DO NOTmix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type. DO NOTmix battery chemistries. DISPOSEof batteries per local code. DO NOTdispose of batteries in fire. KEEPbatteries out of reach of children. REMOVEbatteries if the device will not be used for several months. CERTIFICATIONS This laser complies with all applicable portions of title 21 of the Code of Federal Regulations set by the Food and Drug Administrations, Center for Devices, and Radiological Health. Complies with 21CFR 1040.10 and 10040.11 except for deviations pursuant to Laser notice No. 50, dated June 24, 2007. This LMPL20 has also been tested and complies with the CE certification requirements set forth in the EC regulations 89/336/EEC and EN 61000-6-1 (EN50082-1), EN 61000-6-3 (EN50081-1) and EN 60825-1. LMPL20 RC20 ENVIRONMENT PROTECTION Recycle …

Text truncated - open the document above for the full version.

Front Side Back Side

Back Side Removed Circuit Boards Showing Transmitter Module Front Side of Circuit Board Showing LCD Transmitter Module Back Side of Transmitter Module Transmitter Module with Shield Removed

This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. EMC Report for Robert Bosch Tool Corporation on the RC20 Page 1 of 16 731 Enterprise Drive Lexington, KY 40510 Telephone: 859-226-1000 Facsimile: 859-226-1040 www.intertek-etlsemko.com TEST REPORT Report Number: 100087801LEX-002 Project Number: G100087801 Report Issue Date: 7/12/2010 Product Name: RC20 FCCID: TXT-F034K69P01 ICIC: 909G-F03469P01 Standards: Title 47 CFR Part 15 Subpart C and RSS-210 Issue 7; June 2007 Tested by: Client: Intertek Testing Services NA, Inc. 731 Enterprise Drive Lexington, KY 40510 Robert Bosch Tool Corporation 255 West Flemming Watseka, IL 60970 Report prepared by Report reviewed by Bryan C. Taylor, Team Leader Jason Centers, Senior Project Engineer Intertek Report Number: 100087801LEX-002 Issued: 7/12/2010 EMC Report for Robert Bosch Tool Corporation on the RC20 FCCID:TXT-F034K69P01; ICID:909G-F03469P01 Page 2 of 16 TABLE OF CONTENTS 1 Introduction and Conclusion .............................................................................................................. 3 2 Test Summary ...................................................................................................................................... 3 3 Description of Equipment Under Test ............................................................................................... 4 4 Radiated Emissions Per FCC Part 15.249 (a, d) (Fundamental, Harmonics, and Spurious Emissions) ................................................................................................................................................... 6 5 Radiated Emissions per FCC Part 15.109 (Receive Mode) ............................................................ 10 6 Antenna Requirement per FCC Part 15.203..................................................................................... 14 7 Measurement Uncertainty ................................................................................................................. 15 8 Revision History................................................................................................................................. 16 Intertek Report Number: 100087801LEX-002 Issued: 7/12/2010 EMC Report for Robert Bosch Tool Corporation on the RC20 FCCID:TXT-F034K69P01; ICID:909G-F03469P01 Page 3 of 16 1 Introduction and Conclusion The tests indicated in section 2 were performed on the product constructed as described in section 3. The remaining test sections are the verbatim text from the actual data sheets used during the investigation. These test sections include the test name, the specified test method, a list of the actual test equipment used, documentation photos, results and raw data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested complied with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. The INTERTEK-Lexington is located at 731 Enterprise Drive, Lexington Kentucky, 40510. The radiated emission test site is a 10-meter semi-anechoic chamber. The chamber meets the characteristics of CISPR 16-1 and ANSI C63.4. For measurements, a remotely controlled flush-mount metal-top turntable is used to rotate the EUT a full 360 degrees. A remote controlled non-conductive antenna mast is used to scan the antenna height from one to four meters. The test site is listed with the FCC under registration number 485103. The test site is listed with Industry Canada under site number IC 2042M-1. 2 Test Summary Section Test full name Industry Canada Reference Test date Result 4 Radiated Emissions Per FCC Part 15.249 (a, d) (Fundamental, Harmonics, and Spurious Emissions) RSS-210 (2.2) 5/11/2010 – 5/21/2010 Pass 10 Radiated Emissions per FCC Part 15.109 (Receive Mode) RSS-210 (2.3); RSS-Gen 5/23/2010 Pass 14 Antenna Requirement per FCC Part 15.203 --- 5/23/2010 Pass Intertek Report Number: 100087801LEX-002 Issued: 7/12/2010 EMC Report for Robert Bosch Tool Corporation on the RC20 FCCID:TXT-F034K69P01; ICID:909G-F03469P01 Page 4 of 16 3 Description of Equipment Under Test Equipment Under Test Manufacturer Robert Bosch Tool Corporation Model Number RC20 Serial Number Test Sample 1 Receive Date 4/15/2010 Device Received Condition Good Frequency Band 2.4GHz ISM Band (2.4095MHz) Mode(s) of Operation 802.15 (Zigbee) Modulation Type QPSK Duty Cycle 8.4% (Averaged over 100mS) Transmission Control Test Commands Maximum Output Power 16.24dBm (EIRP) Test Channels 2.4095MHz Antenna Type Internal PCB Operating Voltage 12VDC Description of Equipment Under Test The RC20 is a hand held remote control for the electronic self-leveling pipe laser product (LMPL20). It is used to remotely control the functions of the laser. Operating modes of the EUT: No. Descriptions of EUT Exercising 1 The transmission was controlled by attaching a plastic clamp to one of the buttons on the RC20 in order to force continuous transmission. According to Robert Bosch Tool Corporation, the RC20 only operates on one fr…

Text truncated - open the document above for the full version.

Radiated Emissions Radiated Emissions Orthogonal Configuration (Back) Orthogonal Configuration (Side)