TYLSM3Smoke Detector

ACCESSORIES The LS-30 system includes a full range of accessories, so you can customize many feature of your security system. All the radio transmitters used in the LS-30 system, except the Remote Controller, have a unique random code that is set by the factory with 16,777,216 combinations in total. Also with specially designed transmission timing control, the LS-30 system can effectively prevent mutual interference from other transmitters in the system. The Remote Controller uses copy-preventing hopping-code technology, changing its radio code every time you press the button. The combinations possible through this hopping-code are up to 7.3 X 10 19 . To comply with the regulations in most countries, radio power is limited to below 10mW, and effective range is about 100 meters measured at open field. The range may be somewhat less indoors, depending on the layout of building construction and furniture. You may enroll all the wireless accessories and change their related settings, either through the guidance of the interactive LCD display on the Base Unit explained in the “INSTALLATION” section that follows, or by using a computer with the proprietary software “HyperSecureLink” through an interface adapter, which offers a quicker and simpler way to perform the installation in. NOTE: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. SMOKE DETECTOR INSTALLATION 1. Loose the bottom base of the SM-3S, and insert 9V battery properly. 2. Select “Installer Mode” on the Base Unit, and enter Installer Password to gain access authority. Then select \Set Device\Enroll Device\Fire Sensor\Enter Zone No. to enroll the ID of SM-3S by pressing its TEST button. You may change its various attributes under \Set Device\Change Device Setting\Fire Sensor Change, to fulfill different requirements. 3. Locate the SM-3S properly, and keep it within effective radio range of the Base Unit. 4. Press the “TEST” button, and check if the Base Unit is activated. Notes: 1) The LED starts flashing after a few seconds when smoke is detected, then the internal buzzer sounds and activates the Base Unit after 10 seconds. 2) The LED flashes every 45 seconds to indicate the detector is in standby mode, and it beeps periodically if the 9V battery goes too low. Replace the battery when these beeps occur. 3) Maintenance at least once a year is essential. Open the cover and clean the sensing chamber with a vacuum cleaner carefully. 4) The SM-3S comes with cover latches that prevent the cover from closing if no battery is installed. PREFERRED LOCATIONS LOCATIONS TO BE AVOIDED Do NOT locate detector in: • The kitchen: Smoke from cooking might cause an unwanted alarm. • Near ventilating fan, fluorescent lamp or Air-Conditioning equipment: Air drafts from them may affect the sensitivity of the detector. • Near ceiling beams or over cabinet: Stagnant air in these areas may affect the sensitivity of the detector. • In the peak of an 'A' frame type of ceiling. SPECIFICATIONS: Detection: Photo-electric Chamber Sensitivity: meets UL 217 Power: 9V alkaline battery Temperature: 0 - 50 Relative Humidity: 10% ～ 85% Alarm Sound Level: 85dB@3m Indicator Light: LED flashes every 45 seconds Low Battery: Beep every 45 seconds Current Drain: 6.5uA @standby, 24mA @activation Battery Life: About 2 years. Actuation Indicator: LED ON, Buzzer ON Size: W 140mm x H 45mm Weight: about 288g (w/ battery) Fig. 1: Locations for placing smoke detectors for single residence with only one sleeping area. Fig. 2: Locations for placing smoke detectors for single-floor residence with more than one sleeping area. FA MI LY RO OM KITCHEN LIVING ROOM BEDROOM SECURITY SMOKE DETECTORS FOR MORE SECURITY BED ROOM BED ROOM BED ROOM KITCHEN LIVING ROOM z SMOKE DETECTORS FOR MINIMUM SECURITY { SMOKE DETECTORS FOR MORE SECURITY BEDROOM DINING ROOM BED ROOM BED ROOM ³0.6m ́ At least 0.6m from the wall

FCC ID: TYLSM3 Device Name: Smoke Detector Model No.: SM-2S Date: 2005/12/12 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, the undersigned, hereby authorize ELECTRONICS TESTING CENTER, TAIWAN, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by ELECTRONICS TESTING CENTER, TAIWAN on our behalf shall have the same effect as acts of our own. In authorizing ELECTRONICS TESTING CENTER, TAIWAN as our agent, we still recognize that we are responsible to: a)comply with the relevant provisions of the certification program; b)make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c)make claims regarding certification only in respect of the scope for which certification has been granted; d)do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e)upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f)use certification only to indicate the products are certified as being in conformity with specified standards; g)endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By:By: Kevin Wang (Signature)(Printed) Title:Marketing Manager Applicant:Scientech Electronics Co., Ltd. Address:4F, No. 501-17. Chung-Cheng Rd., Hsin-Tien City, Taipei 231, Taiwan, R.O.C. Tel:886-2-22183085 Fax:886-2-22187380

FCC ID: TYLTSM3 Federal Communications Commission Dear Sir: Pursuant to Section 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Descriptions The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. By:By: Kevin Wang (Signature)(Printed) Title:Marketing Manager Applicant: Scientech Electronics Co., Ltd. Address:4F, No. 501-17. Chung-Cheng Rd., Hsin-Tien City, Taipei 231, Taiwan, R.O.C. Tel:886-2-22183085 Fax:886-2-22187380

ETC Report No.: ET94S-09-165-04 Page A1 of A1 FCC ID.:TYLSM3 ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT

SM-3S 6mm 16mm Model: SM-3S FCC ID:TYLSM3

ETC Report No.: ET94S-09-165-04 Page B1 of B3 FCC ID.: TYLSM3 ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Inside View 1 of EUT 2. Inside View 2 of EUT ETC Report No.: ET94S-09-165-04 Page B2 of B3 FCC ID.: TYLSM3 3. Front view of PCB1 4. Rear view of PCB1 ETC Report No.: ET94S-09-165-04 Page B3 of B3 FCC ID.: TYLSM3 5. Front view of PCB2 6. Rear view of PCB2

ETC Report No. : ET94S-09-165-04 Sheet 1 of 21 Sheets FCC ID.: TYLSM3 Rev. No 1.0 CONFORMANCE TEST REPORT FOR FCC 47 CFR, Part 15 Subpart C Report No.: ET94S-09-165-04 Client: Scientech Electronics Co., Ltd. Product: Wireless Smoke Detector Model: SM-3S FCC ID: TYLSM3 Manufacturer/supplier: Scientech Electronics Co., Ltd. Date test item received: 2005/09/20 Date test campaign completed: 2005/10/31 Date of issue: 2005/11/22 The test result only corresponds to the tested sample. It is not permitted to copy this report, in part or in full, without the permission of the test laboratory. Total number of pages of this test report: 21 pages Total number of pages of photos: External photos 1 pages Internal photos 3 pages Setup photos 1 pages Test Engineer Checked By Approved By James Mark Joe Hsieh ELECTRONICS TESTING CENTER, TAIWAN NO.8, LANE 29, WENMING RD., LESHAN TSUEN, GUISHAN SHIANG, TAOYUAN COUNTY, TAIWAN 33383, R.O.C. TEL: (03) 3276170~4 INT: +886-3-3276170~4 FAX: (03) 3276188 INT: +886-3-3276188 ETC Report No. : ET94S-09-165-04 Sheet 2 of 21 Sheets FCC ID.: TYLSM3 Rev. No 1.0 Client : Scientech Electronics Co., Ltd. Address : 4F, No. 501-17, Chung-Cheng Rd., Hsin-Tien City, Taipei 231, Taiwan, R.O.C. Manufacturer : Scientech Electronics Co., Ltd. Address : 4F, No. 501-17, Chung-Cheng Rd., Hsin-Tien City, Taipei 231, Taiwan, R.O.C. EUT : Wireless Smoke Detector Trade name : LifeSOS Model No. : SM-3S Comment issues : (1) The report also apply to model: SM-3A (2) The multiple listing recognized without test basis is according to information supplied by manufacturer. A detail documentation of the above models must be verified by legal right organization for the EMC characteristic with relation to the subject model. Power Source : 9VDC Regulations applied : FCC 47 CFR, Part 15 Subpart C (2005) The testing described in this report has been carried out to the best of our knowledge and ability, and our responsibility is limited to the exercise of reasonable care. This certification is not intended to believe the sellers from their legal and/or contractual obligations. The compliance test is only certified for the test equipment and the results of the testing report relate only to the item tested. The compliance test of this report was conducted in accordance with the appropriate standards. It’s not intention to assure the quality and performance of the product. This report shall not be reproduced except in full, without the approval of ETC. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Laboratory Introduction: Electronics Testing Center, Taiwan is recognized, filed and mutual recognition arrangement as following: 1 ISO9001: TüV Product Service 2 ISO/IEC 17025: BSMI, CNLA, DGT, NVLAP, CCIBLAC, UL, Compliance 3 Filing: FCC, Industry Canada, VCCI 4 MRA: Australia, Hong Kong, New Zealand, Singapore, USA, Japan, Korea, China, APLAC through CNLA 5 FCC Registration Number: 90588, 91094, 91095 NVLAP Lab Code 200133-0 ETC Report No. : ET94S-09-165-04 Sheet 3 of 21 Sheets FCC ID.: TYLSM3 Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION ......................................................................................................................................4 1.1 PRODUCT DESCRIPTION................................................................................................................................................. 4 1.2 CHARACTERISTICS OF DEVICE: ...................................................................................................................................... 4 1.3 TEST METHODOLOGY.................................................................................................................................................... 4 1.4 TEST FACILITY............................................................................................................................................................... 4 2. DEFINITION AND LIMITS........................................................................................................................................5 2.1 DEFINITION.................................................................................................................................................................... 5 2.2 RESTRICTED BANDS OF OPERATION............................................................................................................................... 5 2.3 LIMITATION.................................................................................................................................................................... 6 2.4 LABELING REQUIREMENT.............................................................................................................................................. 7 2.5 USER INFORMATION....................................................................................................................................................... 7 3. RADIATED EMISSION MEASUREMENT..............................................................................................................8 3.1 APPLICABLE STANDARD................................................................................................................................................. 8 3.2 MEASUREMENT PROCEDURE......................................................................................................................................... 8 3.3 TEST DATA.................................................................................................................................................................. 10 3.4 FIELD STRENGTH CALCULATION.................................................................................................................................. 12 3.5 RADIATED TEST EQUIPMENT....................................................................................................................................... 12…

Text truncated - open the document above for the full version.

ETC Report No.:ET94S-09-165-04 Sheet 1 of 1 Sheets FCC ID.: TYLSM3 Radiated Measurement Photos