U6XFU2SPHearing Aid

Bernafon Radio Model - Quick Installation Guide Bernafon Model Name: FUSION 2 SP The FUSION 2 SP radio model is a low power, inductive radio transceiver working at 3.84 MHz consisting of an RF Engine Block (incl. DSP, radio & memory), antenna coil, motherboard (incl. small passive components) and intended to be installed as a module into Bernafon wireless hearing aid devices only. The module also has all voltage regulators included inside the engine block. The module requires a battery, one or two microphones on a flex PCB and a speaker to be attached and must be mounted in an external plastic shell. It is possible for authorized personnel only to program the module through a flex I/O. The module is depicted below: FUSION 2 SP Radio Model (seen from the top side) FUSION 2 SP Radio Model (seen from the bottom) RF Engine Block Antenna Motherboard Battery - Battery + Program flex I/O Speaker unit connectors Mic flex 1 Bernafon Radio Model - Quick Installation Guide Radio Model Name: FUSION 2 SP FUSION 2 SP Radio Model (seen from the side) FCC ID: U6XFU2SP IC: 7031A-FU2SP 2 Bernafon Radio Model - Regulatory Label Information Radio Model Name: FUSION 2 SP Contains: FCC ID: U6XFU2SP IC: 7031A-FU2SP NOTICE: This device complies with Part 15 of the FCC Rules and with the license exempt standard RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Bernafon may void the FCC authorization to operate this equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 3

Test report no.: 1-8930_14-01-01_AnnexB Page 1 of 6 Annex B This test report annex is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report annex authorised: Tobias Wittenmeier Radio Communications & EMC Test report no.: 1-8930_14-01-01_AnnexB Page 2 of 6 Internal photos of the EUT Photo 1: Photo 2: Test report no.: 1-8930_14-01-01_AnnexB Page 3 of 6 Photo 3: Photo 4: Test report no.: 1-8930_14-01-01_AnnexB Page 4 of 6 Photo 5: Photo 6: Test report no.: 1-8930_14-01-01_AnnexB Page 5 of 6 Photo 7: Test report no.: 1-8930_14-01-01_AnnexB Page 6 of 6 Document history Version Applied changes Date of release Initial release 2015-01-28

Bernafon Radio Model - Regulatory Label Information Radio Model Name: FUSION 2 SP Contains: FCC ID: U6XFU2SP IC: 7031A-FU2SP NOTICE: This device complies with Part 15 of the FCC Rules and with the license exempt standard RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Bernafon may void the FCC authorization to operate this equipment. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 3

Test report no.: 1-8930_14-01-01_AnnexB Page 1 of 6 Annex B This test report annex is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report annex authorised: Tobias Wittenmeier Radio Communications & EMC Test report no.: 1-8930_14-01-01_AnnexB Page 2 of 6 Internal photos of the EUT Photo 1: Photo 2: Test report no.: 1-8930_14-01-01_AnnexB Page 3 of 6 Photo 3: Photo 4: Test report no.: 1-8930_14-01-01_AnnexB Page 4 of 6 Photo 5: Photo 6: Test report no.: 1-8930_14-01-01_AnnexB Page 5 of 6 Photo 7: Test report no.: 1-8930_14-01-01_AnnexB Page 6 of 6 Document history Version Applied changes Date of release Initial release 2015-01-28

TEST REPORT Test report no.: 1-8930/14-01-04-A Testing laboratory Applicant CETECOM ICT Services GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: http://www.cetecom.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2005) by the Deutsche Akkreditierungsstelle GmbH (DAkkS) The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12076-01-00 Bernafon AG Morgenstraße 131 3018 Bern / SWITZERLAND Phone: +41 31 9 98 15 15 Fax: -/- Contact: Stefan Beelte e-mail: -/- Phone: +41 3 19 98 15 18 Manufacturer Bernafon AG Morgenstraße 131 3018 Bern / SWITZERLAND Test standard/s 47 CFR Part 15 Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 210 Issue 8 Spectrum Management and Telecommunications Radio Standards Specification - Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment RSS - Gen Issue 4 Spectrum Management and Telecommunications Radio Standards Specifications - General Requirements and Information for the Certification of Radio ApparatusSpectrum Management and Telecommunications Radio Standards Specifications - General Requirements and Information for the Certification of Radio Apparatus For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: Hearing Instrument Model name: Fusion 2 SP (FU2SP) FCC ID: U6XFU2SP IC: 7031A-FU2SP Frequency: 3.84 MHz Technology tested: Magnetic coupling Antenna: Integrated coil antenna Power supply: 1.4V DC by zinc-air battery Temperature range: 0°C to +40°C This test report is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorised: Test performed: p.o. Marco Bertolino Tobias Wittenmeier Radio Communications & EMC Radio Communications & EMC Test report no.: 1-8930/14-01-04-A Page 2 of 28 1 Table of contents 1 Table of contents ............................................................................................................................................ 2 2 General information ....................................................................................................................................... 3 2.1 Notes and disclaimer ......................................................................................................................... 3 2.2 Application details ............................................................................................................................. 3 3 Test standard/s ............................................................................................................................................... 3 4 Test environment ............................................................................................................................................ 4 5 Test item .......................................................................................................................................................... 4 5.1 Additional information ...................................................................................................................... 4 6 Test laboratories sub-contracted ................................................................................................................. 4 7 Description of the test setup ......................................................................................................................... 5 7.1 Radiated measurements ................................................................................................................... 5 7.2 Conducted measurements ................................................................................................................ 6 8 Summary of measurement results ............................................................................................................... 7 9 Additional comments ..................................................................................................................................... 8 10 Measurement results ................................................................................................................................. 9 10.1 Timing of the transmitter .................................................................................................................. 9 10.2 Bandwidth of the modulated carrier .............................................................................................. 10 10.3 Field strength of the fundamental .................................................................................................. 14 10.4 Field strength of the harmonics and spurious ............................................................................. 15 10.5 Receiver spurious emissions ......................................................................................................... 22 10.6 Conducted limits .............................................................................................................................. 25 11 Test equipment and ancillaries used for tests ..................................................................................... 26 12 Observations ............................................................................................................................................ 26 Annex A Document history ............................................................................................................................ 27 Annex B Further information ......................................................................................................................... 27 Annex C Accreditation Certificate ..........…

Text truncated - open the document above for the full version.

Test report no.: 1-8930_14-01-01_AnnexD Page 1 of 7 Annex D This test report annex is electronically signed and valid without handwriting signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report annex authorised: Tobias Wittenmeier Radio Communications & EMC Test report no.: 1-8930_14-01-01_AnnexD Page 2 of 7 EUT Test setup photos Photo 1: Photo 2: Test report no.: 1-8930_14-01-01_AnnexD Page 3 of 7 Photo 3: Photo 4: Test report no.: 1-8930_14-01-01_AnnexD Page 4 of 7 Photo 5: Photo 6: Test report no.: 1-8930_14-01-01_AnnexD Page 5 of 7 Photo 7: Photo 8: Test report no.: 1-8930_14-01-01_AnnexD Page 6 of 7 Photo 9: Test report no.: 1-8930_14-01-01_AnnexD Page 7 of 7 Document history Version Applied changes Date of release Initial release 2015-01-28