V36WL-700N-ART802.11N WIRELESS ADAPTER

55 44 33 22 11 D D C C B B A A TitleSize Document Number Rev Date: Sheet of BLOCK-1X1-24G.SCH 3.3 Block Diagram - 2.4GHz USB 1T1R RALINK TECHNOLOGY, CORP. C 66 Thursday, May 27, 2010 TitleSize Document Number Rev Date: Sheet of BLOCK-1X1-24G.SCH 3.3 Block Diagram - 2.4GHz USB 1T1R RALINK TECHNOLOGY, CORP. C 66 Thursday, May 27, 2010 TitleSize Document Number Rev Date: Sheet of BLOCK-1X1-24G.SCH 3.3 Block Diagram - 2.4GHz USB 1T1R RALINK TECHNOLOGY, CORP. C 66 Thursday, May 27, 2010 USB Interface 3.3V 5V Interface Signals 2.4G TX02.4G RX0 Antenna PA RTL8188SU Switching Regulator EEPROM Crystal40MHZ

External Photo External Photo External Photo External Photo

FCC ID LABEL FCC ID:V36WL-700N-ART Label Location on EUT EUT Bottom View/ FCC ID Label Location

Internal Photo Internal Photo Antenna Internal Photo

1. U3 is regulates power, which reguates power from 5V to 3.3V and supply for MCU 2. U1 inclludes RF single chip,PA 3. CON3 is conneting PC USB 4. X1 is provide 40MHZ crystal clock

1 2 3 4 5 6 78 ABCD 8 7 6 5 4 3 2 1 D CBA 1 23 4 X140MHz C3620pF C3520pF WU8188 / 07 EECS VDD33VDD18VDD33VDD18 VDD33 VDD18 VDD15 VDD12VDD18VDD25VDD33 VDD33 VDD33 VDD12 R324KR XI_40M XO_40M XI_40M XO_40M C41p2FC31p2F L52n7HL42n7H C11u0F TX2G_PA[0]-TX2G_PA[0]+RX2G[0]+RX2G[0]- C181u0F C151u0FC111u0F L86n8H C51u0FC60u1FC90u1FC100u1F C170u1F C120u1FC131u0FC140u1F C2010uF C2122uF C20u1F L26u8H VDD18 C160u1F L96n8H C2510pFC2610pF VDD33VDD33 C272p7FC282p7F L63n3H C311n0HC321n0H L124n7H C231p0F C240p8F L33n3H C2210uF VDD33 1234 CON3USB 5V HSDNHSDP EN 1 GND 2 SW 3 VIN 4 FB 5 U3CAT7103 L334u7H C3822uF R6680KRR7150KR C4010nF 5V VDD33 C3710uF R5100KR C3910nF 5V HSDNHSDP R8NP R910KR C41NP GPIO[0] GPIO[1] VDD33 VDD33 VDD33 R101K0R C810pF R126K2R EESK EEDI EEDO CON1 R220 R21NPR23NP LED1LED LED0LED R2560R R1560R LED[0] LED[1] VDD33 C48100pF CHIP_SELECT 1 DATA_ CLK 2 DATA_IN 3 DATA_OUT 4 GND 5 ORG 6 X 7 VCC 8 U2NP EECSEESKEEDIEEDO VDD33 TRSWP[0] 2 VD33_PA 3 PAPE[0] 1 TX2G_PAON[0] 4 TX2G_PAOP[0] 5 PAPE[1] 10 RX2G_IN[0] 9 XO 26 ANT_SEL_P 17 EECS 63 TRSWN[0] 6 VD33R 11 NC 12 EESK 62 EEDI / GPIO[7] / USOUT 61 EEDO / GPIO[6] / USIN 60 RX2G_IP[0] 8 NC 13 VD18R[1] 14 VD18D 34 VDD12_D 58 NC 46 GND_D 28 VD33IO 55 GGPIO[4] 56 VD33U 36 PDn 48 NC 54 NC 53 GND_D 59 TSSI _0 64 HSDP 38 NC 16 NC 15 ANT_SEL_N 18 BT_PRI / GPIO[3] 32 LED[1] 20 NC 44 LED[0] 19 VD12S 40 NC 42 VD33A 21 GND_SPS_0 49 REXT 22 XI 25 NC 27 WL_ACT / GPIO[0] / EEPROM 29 HSDM 39 NC 52 VD33_SPS_0 51 NC 47 LX_SPS_0 50 VD18A 23 VDD15A 24 GPIO[5] 57 BT_FREQ / GPIO[1] / HCI_SEL 30 VD25E 35 VD12D 33 RREF 37 GND_S 41 NC 43 NC 45 BT_STA / GPIO[2] 31 VD18R[0] 7 GND_RF 65 U1RTL8188SU

FCC PART 15 CLASS B EMI MEASUREMENT AND TEST REPORT For Blupont Limited Tianfa Building CD 218 RM, Tian’An Cyber Park, Tairan 5 Road, Futian District, Shenzhen, China FCC ID:V36WL-700N-ART Jun. 15, 2010 This Report Concerns: Original Report Equipment Type 802.11N WIRELESS ADAPTER Test Engineer: Jack Liu Report No.: BST10050553R-3 Receive EUT Date/Test Date: Jun. 08,2010/ Jun. 08-Jun. 15,2010 Reviewed By: Christina Prepared By: Shenzhen BST Technology Co.,Ltd. 3F,Weames Technology Building, No. 10 Kefa Road,Science Park, Nanshan District,Shenzhen,Guangdong,China Tel: 0755-267477513 Fax: 0755-267477513 ext.826 Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Shenzhen BST Technology Co.,Ltd. This report must not be used by the client to claim product certification,approval,or endorsement by NVLAP, NIST or any agency of the US Government. Blupont Limited FCC ID: V36WL-700N-ART BST FCC ID REPORT : BST10050553R-3 Page 2/13 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1. Report information............................................................................................................ 3 1.2. Measurement Uncertainty................................................................................................. 3 2. PRODUCT DESCRIPTION ...................................................................................................... 4 2.1. EUT Description ............................................................................................................... 4 2.2. Block Diagram of EUT Configuration ............................................................................. 4 2.3. Support Equipment List .................................................................................................... 4 2.4. Test Conditions .................................................................................................................4 3. FCC ID LABEL........................................................................................................................... 5 4. TEST RESULTS SUMMARY ................................................................................................... 6 Modifications ................................................................................................................................ 6 5. TEST EQUIPMENT USED ....................................................................................................... 7 5.1. For Conducted Emission Test ........................................................................................... 7 5.2. For Radiated Emission Measurement ............................................................................... 7 6. CONDUCTED EMISSION TEST............................................................................................. 8 6.1. Block Diagram of Test Setup............................................................................................ 8 6.2. Test Standard .................................................................................................................... 8 6.3. Conducted Emission Limit(Class B) ................................................................................ 8 6.4. EUT Configuration on Test .............................................................................................. 8 6.5. Operating Condition of EUT ............................................................................................ 8 6.6. Test Procedure ..................................................................................................................9 6.7. Test Result ........................................................................................................................ 9 7. RADIATED EMISSION MEASUREMENT ......................................................................... 10 7.1. Block Diagram of EUT Configuration ........................................................................... 10 7.2. Test Standard ..................................................................................................................10 7.3. Radiated Emission Limit(Class B) ................................................................................. 10 7.4. EUT Configuration on Test ............................................................................................ 11 7.5. Operating Condition of EUT .......................................................................................... 11 7.6. Test Procedure ................................................................................................................ 11 7.7. Test Result ...................................................................................................................... 11 APPENDIX I ......................................................................................................................................... 12 Blupont Limited FCC ID: V36WL-700N-ART BST FCC ID REPORT : BST10050553R-3 Page 3/13 1. GENERAL INFORMATION 1.1. Report information 1.1.1.This report is not a certificate of quality; it only applies to the sample of the specific product/equipment given at the time of its testing. The results are not used to indicate or imply that they are application to the similar items. In addition, such results must not be used to indicate or imply that BST approves recommends or endorses the manufacture, supplier or use of such product/equipment, or that BST in any way guarantees the later performance of the product/equipment. 1.1.2.The sample/s mentioned in this report is/are supplied by Applicant, BST therefore assumes no responsibility for the accuracy of information on the brand name, model number, origin of manufacture or any information supplied. Additional copies of the report are available to the Applic…

Text truncated - open the document above for the full version.

FCC PART 15.247 EMI MEASUREMENT AND TEST REPORT For Blupont Limited Tianfa Building CD 218 RM, Tian’An Cyber Park, Tairan 5 Road, Futian District, Shenzhen, China FCC ID:V36WL-700N-ART Jun. 15, 2010 This Report Concerns: Original Report Equipment Type 802.11N WIRELESS ADAPTER Test Engineer: Jack Liu Report No.: BST10050552ER-3 Receive EUT Date/Test Date: Jun. 08,2010/ Jun. 08-Jun. 15,2010 Reviewed By: Christina Prepared By: Shenzhen BST Technology Co.,Ltd. 3F,Weames Technology Building, No. 10 Kefa Road,Science Park, Nanshan District,Shenzhen,Guangdong,China Tel: 0755-267477513 Fax: 0755-267477513 ext.826 Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Shenzhen BST Technology Co.,Ltd. This report must not be used by the client to claim product certification,approval,or endorsement by NVLAP, NIST or any agency of the US Government. Blupont Limited FCC ID: V36WL-700N-ART BST FCC ID REPORT : BST10050552ER-3 Page 2/48 TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................4 1.1. Report information ............................................................................................................4 1.2. Measurement Uncertainty .................................................................................................4 2. PRODUCT DESCRIPTION ......................................................................................................5 2.1. EUT Description ...............................................................................................................5 2.2. Block Diagram of EUT Configuration..............................................................................5 2.3. Support Equipment List ....................................................................................................5 2.4. Test Conditions .................................................................................................................6 3. FCC ID LABEL...........................................................................................................................6 4. TEST RESULTS SUMMARY ...................................................................................................7 Modifications ................................................................................................................................7 5. TEST EQUIPMENT USED .......................................................................................................8 6. §15.247 (I) AND §1.1307 (B) (1) - MAXIMUM PERMISSIBLE EXPOSURE (MPE)............9 6.1. Standard Applicable..........................................................................................................9 6.2. Test Data ...........................................................................................................................9 6.3. Test Result ......................................................................................................................11 7. §15.203 - ANTENNA REQUIREMENT .................................................................................12 7.1. Standard Applicable........................................................................................................12 7.2. Antenna Connector Construction....................................................................................12 8. §15.207 - CONDUCTED EMISSIONS....................................................................................13 8.1. Applicable Standard........................................................................................................13 8.2. Test Procedure ................................................................................................................13 8.3. Conducted Power line Emission Limits..........................................................................13 8.4. Conducted Power Line Test Result.................................................................................13 9. §15.209, §15.205, §15.247(D) - SPURIOUS EMISSIONS .....................................................14 9.1. Test Equipment ...............................................................................................................14 9.2. Test Procedure ................................................................................................................14 9.3. Radiated Test Setup ........................................................................................................14 9.4. Radiated Emission Limit.................................................................................................14 9.5. Radiated Emission Test Result .......................................................................................15 10. §15.247(A) (2) – 6DB BANDWIDTH TESTING....................................................................28 10.1. Test Equipment ...............................................................................................................28 10.2. Test Procedure ................................................................................................................28 10.3.Applicable Standard ............................................................................................................28 10.3. Test Result:Pass. .............................................................................................................28 11. §15.247(B) (3) - MAXIMUM PEAK OUTPUT POWER ......................................................35 11.1. Test Equipment ...............................................................................................................35 11.2. Test Procedure ................................................................................................................35 11.3. Applicable Standard.....................................................................…

Text truncated - open the document above for the full version.