VIYHRM1026AWireless Low Energy Module

User manual Product: Wireless low energy module Model: HRM1026A For OEM integration only – device cannot be sold to general public. Therefore we will not supply the User’s manual, the installation manual is the official for OEM. FCC ID: VIYHRM1026A IC: 7305A-HRM1026A ■Operational Information This module has been tested and found to comply with the limits for a Class B digital device pursuant to Part15 of FCC rules. This module complies with Part15 subpart C of the FCC rules. Customers should check Part15 subpart B compliance with their own final products and conduct certification if needed. ■Caution Any changes or modifications are not expressly approved by Hosiden responsible for compliance could void the user’s authority to operate the equipment. ■Requirement of Labeling Please describe the following item on the final product including this module: or or ■Requirement of User’s Manual Statement “This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.” Contains Transmitter Module FCC ID: VIYHRM1026A Contains FCC ID: VIYHRM1026A Contains Transmitter Module IC: 7305A-HRM1026A Contains IC: 7305A-HRM1026A Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: VIYHRM1026A”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut êtr…

Text truncated - open the document above for the full version.

FCC ID: VIYHRM1026A Report No.: RF140312C05 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch April 28, 2014 Dear Application Examiner, Hosiden Coporation, FCC ID: VIYHRM1026A would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data input, it is integrated in chip nRF51822. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is nRF51822. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT EUT with Dual crystals

Label information Overview Top side Bottom side Note) FCC ID, IC ID and model name will be displayed on the shield case by laser marking.

Page 2 EUT with Dual crystals

Report No.: SA140312C05 R1 1 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA140312C05 dated Mar. 19, 2014 RF EXPOSURE REPORT REPORT NO.: SA140312C05 R1 MODEL NO.: HRM1026A FCC ID: VIYHRM1026A IC: 7305A-HRM1026A RECEIVED: Mar. 12, 2014 TESTED: Mar. 15 ~ Mar. 18, 2014 ISSUED: May 21, 2014 APPLICANT: Hosiden Corporation ADDRESS: 4-33, Kitakyuhoji 1-chome Yao-City, Osaka 581-0071, Japan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA140312C05 R1 2 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA140312C05 dated Mar. 19, 2014 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION .............................................................................................. 4 2. EVALUATION RESULT .................................................................................... 5 3. SAR TEST EXCLUSION THRESHOLDS ......................................................... 6 Report No.: SA140312C05 R1 3 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA140312C05 dated Mar. 19, 2014 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140312C05 Original release Mar. 19, 2014 SA140312C05 R1 Changed product name May 21, 2014 Report No.: SA140312C05 R1 4 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA140312C05 dated Mar. 19, 2014 1. CERTIFICATION PRODUCT: Wireless Low Energy Module MODEL: HRM1026A BRAND: Hosiden APPLICANT: Hosiden Corporation TESTED: Mar. 15 ~ Mar. 18, 2014 TEST SAMPLE: Production Prototype STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 RSS-102 Issue 4 (2010-12) The above equipment (Model: HRM1026A) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : May 21, 2014 Pettie Chen / Senior Specialist APPROVED BY : , DATE : May 21, 2014 Ken Liu / Senior Manager Report No.: SA140312C05 R1 5 of 6 Report Format Version 5.0.0 Cancels and replaces the report No.: SA140312C05 dated Mar. 19, 2014 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where  f(GHz) is the RF channel transmit frequency in GHz .  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [(Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [(Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA140312C05 R1 6 of 6 Report Format Version 5.0…

Text truncated - open the document above for the full version.

Report No.: RF140312C05 R1 1 of 48 Report Format Version 5.2.0 Cancels and replaces the report No.: RF140312C05 dated Apr. 30, 2014. FCC TEST REPORT REPORT NO.: RF140312C05 R1 MODEL NO.: HRM1026A FCC ID: VIYHRM1026A IC: 7305A-HRM1026A RECEIVED: Mar. 12, 2014 TESTED: Mar. 15 ~ Apr. 29, 2014 ISSUED: May 21, 2014 APPLICANT: Hosiden Corporation ADDRESS: 4-33, Kitakyuhoji 1-chome Yao-City, Osaka 581-0071, Japan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140312C05 R1 2 of 48 Report Format Version 5.2.0 Cancels and replaces the report No.: RF140312C05 dated Apr. 30, 2014. Table of Contents RELEASE CONTROL RECORD .......................................................................................... 4 1. CERTIFICATION ....................................................................................................... 5 2. SUMMARY OF TEST RESULTS .............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 6 3. GENERAL INFORMATION ....................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ......................................................................... 7 3.2 DESCRIPTION OF TEST MODES ........................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................... 9 3.3 DESCRIPTION OF SUPPORT UNITS ................................................................... 10 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 11 4. TEST TYPES AND RESULTS ................................................................................ 12 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 12 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 12 4.1.2 TEST INSTRUMENTS ........................................................................................... 13 4.1.3 TEST PROCEDURES ............................................................................................ 14 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 14 4.1.5 TEST SETUP ......................................................................................................... 15 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 15 4.1.7 TEST RESULTS ..................................................................................................... 16 4.2 CONDUCTED EMISSION MEASUREMENT ......................................................... 26 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 26 4.2.2 TEST INSTRUMENTS ........................................................................................... 26 4.2.3 TEST PROCEDURES ............................................................................................ 27 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 27 4.2.5 TEST SETUP ......................................................................................................... 27 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 27 4.2.7 TEST RESULTS ..................................................................................................... 28 4.3 6dB BANDWIDTH MEASUREMENT ..................................................................... 30 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................... 30 4.3.2 TEST SETUP ......................................................................................................... 30 4.3.3 TEST INSTRUMENTS ........................................................................................... 30 4.3.4 TEST PROCEDURE .............................................................................................. 30 4.3.5 DEVIATION FROM TEST STANDARD .................................................................. 30 4.3.6 EUT OPERATING CONDITIONS .........................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST 2 3 CONDUCTED EMISSION TEST 4