VIYHRM1034Bluetooth module

User manual Product: Bluetooth module Model: HRM1034 For OEM integration only – device cannot be sold to general public. Therefore we will not supply the User’s manual, the installation manual is the official for OEM. FCC ID: VIYHRM1034 IC: 7305A-HRM1034 ■Operational Information This module has been tested and found to comply with the limits for a Class B digital device pursuant to Part15 of FCC rules. This module complies with Part15 subpart C of the FCC rules. Customers should check Part15 subpart B compliance with their own final products and conduct certification if needed. ■Caution Any changes or modifications are not expressly approved by Hosiden responsible for compliance could void the user’s authority to operate the equipment. ■Requirement of Labeling Please describe the following item on the final product including this module: or or ■Requirement of User’s Manual Statement “This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.” Contains Transmitter Module FCC ID: VIYHRM1034 Contains FCC ID: VIYHRM1034 Contains Transmitter Module IC: 7305A-HRM1034 Contains IC: 7305A-HRM1034 The following statements must be described on the user manual of the host device of this module; Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: ・For Mobile Use This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). ・For Portable Use This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption rate(SAR). This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada Statement This device complies with RSS-standard(s) of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement/ Déclaration d'exposition aux radiations: ・For Mobile Use This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-10…

Text truncated - open the document above for the full version.

External Photographs of HRM1034 <Top view> <Bottom View>

Label information Overview Top side Bottom side

External Photographs of HRM1034 <Top view> <Bottom View>

UL Japan, Inc. Ise EMC Lab 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan T:: +81.596.24.8999 / F:: +81.596.24.8124 / W:: ul.com/jp October 22, 2014 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID: VIYHRM1034 To whom it may concern, We, UL Japan, Inc, hereby declare that Bluetooth audio module, model: HRM1034 (FCC ID: VIYHRM1034) of Hosiden Corporation is exempt from RF exposure SAR evaluation as its output power meets the exclusion limits stated in KDB 447498D01(V05). KDB 447498D01(V05) has the following exclusion for portable devices: The 1g and 10g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where •f(GHz) is the RF channel transmit frequency in GHz •Power and distance are rounded to the nearest mW and mm before calculation •The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. This device has f = 2.48 GHz and distance = 5 mm (minimum separation distance: 5mm was used in the calculation) and the maximum tune-up tolerance limit was 3 mW (Measured value). So for this device: 3 mW[maximum tune-up tolerance limit]/5 mm[minimum separation distance]*√2.48 = 0.9 *This is less than 3.0, so no SAR is required. Thank you for your attention to this matter. Takayuki Shimada Engineer of Ise EMC Lab. Consumer Technology Division UL Japan, Inc.

Test report No. : 10523242H-A-R1 Page : 2 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 REVISION HISTORY Original Test Report No.: 10523242H-A Revision Test report No. Date Page revised Contents - (Original) 10523242H-A October 22, 2014 - - 1 10523242H-A-R1 November 7, 2014 P.5 Correction of explanatory note for variant model 1 10523242H-A-R1 November 7, 2014 P.45, 46 Deleted note of test data Test report No. : 10523242H-A-R1 Page : 3 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ......................................................................................................... 4 SECTION 2: Equipment under test (E.U.T.) ........................................................................................... 4 SECTION 3: Test specification, procedures & results ............................................................................ 6 SECTION 4: Operation of E.U.T. during testing .................................................................................... 9 SECTION 5: Conducted Emission .......................................................................................................... 12 SECTION 6: Radiated Spurious Emission ............................................................................................ 13 SECTION 7: Antenna Terminal Conducted Tests ................................................................................ 14 APPENDIX 1: Data of EMI test .............................................................................................................. 15 Conducted Emission ......................................................................................................................... 15 20dB Bandwidth and Carrier Frequency Separation ......................................................................... 19 Number of Hopping Frequency ........................................................................................................ 22 Dwell time ......................................................................................................................................... 24 Maximum Peak Output Power .......................................................................................................... 27 Radiated Spurious Emission ............................................................................................................. 29 Conducted Spurious Emission .......................................................................................................... 48 Conducted Emission Band Edge compliance ................................................................................... 60 99%Occupied Bandwidth ................................................................................................................. 62 APPENDIX 2: Test instruments ............................................................................................................. 64 APPENDIX 3: Photographs of test setup ............................................................................................... 66 Conducted Emission ......................................................................................................................... 66 Radiated Spurious Emission ............................................................................................................. 67 Worst Case Position .......................................................................................................................... 69 Test report No. : 10523242H-A-R1 Page : 4 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name : Hosiden Corporation Address : 1-4-33, Kitakyuhoji, Yao-city, Osaka, 581-0071, Japan Telephone Number : +81-72-924-1195 Facsimile Number : +81-72-993-0724 Contact Person : Keiji Mine SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Bluetooth audio module Model No. : HRM1034 Serial No. : Refer to Section 4, Clause 4.2 Rating : DC 2.7V to 4.2V (Typ. DC 3.7V) Receipt Date of Sample : September 8, 2014 October 15, 2014 Country of Mass-production : China Condition of EUT : Production prototype (Not for Sale: This sample is equivalent to mass-produced items.) Modification of EUT : No Modification by the test lab 2.2 Product Description Model No.: HRM1034 (referred to as the EUT in this report) is the Bluetooth audio module which is installed in the Stereo Speaker: HBG5006 (host device) manufactured by Hosiden Corporation and AV Receiver: TX-SR444 (host device) manufactured by Onkyo Corporation. All the tests were performed with EUT which is installed in the Stereo Speaker as a representative according to the customer’s request. Also, spurious emission test was only performed with EUT which is installed in the AV Receiver. General Specification Clock frequency(ies) in the system : 16MHz Radio Specification [Bluetooth Ver 3.0] Radio Type : Transceiver Frequency of Operation : 2402-2480MHz Modulation : FHSS Power Supply (radio part input) : DC1.25V Antenna type : Printed Meander antenna Antenna Gain : -1.5dBi max Test report No. : 10523242H-A-R1 Page : 5 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Variant model Test report No. : 10523242H-A-R1 Page : 6 of 69 Is…

Text truncated - open the document above for the full version.

Test report No. : 10523242H-A-R1 Page : 66 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 APPENDIX 3: Photographs of test setup Conducted Emission [Host device: Stereo Speaker] Photo 1 Photo 2 Test report No. : 10523242H-A-R1 Page : 67 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Spurious Emission [Host device: Stereo Speaker] Photo 1 Photo 2 Test report No. : 10523242H-A-R1 Page : 68 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Spurious Emission [Host device: AV Receiver] Photo 1 Photo 2 Test report No. : 10523242H-A-R1 Page : 69 of 69 Issued date : October 22, 2014 Revised date : November 7, 2014 FCC ID : VIYHRM1034 UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Worst Case Position [Host device: Stereo Speaker] Above 1GHz (Horizontal: X-axis/ Vertical:Y-axis) Below 1GHz (Horizontal: X-axis/ Vertical:X-axis) X-axis Y-axis Z-axis End of Report