W8F800922576ORPAK PAYMENT TERMINAL (OrPT) PANEL

No. 817426100 Revision A S S e e c c u u r r e e d d O O r r P P T T S S i i n n g g l l e e B B o o x x INSTALLATION MANUAL Secured OrPT Single Box Installation Manual i SAFETY CONSIDERATIONS Read all warning notes and instructions carefully. They are included to help you installing the Product safely in the highly flammable environment of the fuel station. Disregarding these warning notes and instructions could result in serious injury or property damage. It is the installer responsibility to install, operate and maintain the equipment according to the instructions given in this manual, and to conform to all applicable codes, regulations and safety measures. Failure to do so could void all warranties associated with this equipment. Remember that the fuel station environment is highly flammable and combustible. Therefore, make sure that actual installation is performed by experienced personnel, licensed to perform work in fuel station and at a flammable environment, according to the local regulations and relevant standards. WARNING - EXPLOSION HAZARD Use separate conduit for the intrinsically safe wiring. Do not run any other wires or cables through this conduit, because this could create an explosion hazard. Install the Product only in the non-hazardous area of the fuel station. Use standard test equipment only in the non- hazardous area of the fuel station, and approved test equipment for the hazardous areas. In the installation and maintenance of the Product, comply with all applicable requirements of the National Fire Protection Association NFPA-30 “Flammable and Combustible Liquids Code”, NFPA-30A “Automotive and Marine Service Station Code”, NFPA-70 “National Electric Code”, federal, state and local codes and any other applicable safety codes and regulations. Do not perform metal work in a hazardous area. Sparks generated by drilling, tapping and other metal work operations could ignite fuel vapors and flammable liquids, resulting in death, serious personal injury, property loss and damage to you and other persons. CAUTION - SHOCK HAZARD Dangerous AC voltages that could cause death or serious personal injury are used to power the Product. Always disconnect power before starting any work. The Product has more than one power supply connection port. Disconnect all power before servicing. WARNING – PASSING VEHICLES When working in any open area of fuel station, beware of passing vehicles that could hit you. Block off the work area to protect yourself and other persons. Use safety cones or other signaling devices. CAUTION Do not attempt to make any repair on the printed circuit boards residing in the Product, as this will void all warranties related to this equipment. Secured OrPT Single Box Installation Manual ii PROPRIETY NOTICE This document contains propriety and confidential information. It is the property of ORPAK SYSTEMS Ltd. It may not be disclosed or reproduced in whole or in part without written consent of ORPAK SYSTEMS. The information in this document is current as of the date of its publication, but is subject to change without notice. DISCLAIMER This document is provided for reference only. Although every effort has been made to ensure correctness, ORPAK SYSTEMS does not guarantee that there are no errors or omissions in this document. CAUTION For supply connections, use wires suitable for at least 90°C. Signal wiring connected in this box must be rated at least 300 V. FCC COMPLIANCE STATEMENT IN USER'S MANUAL This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. User information for a Class A digital device: THE FCC WANTS YOU TO KNOW: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Secured OrPT Single Box Installation Manual iii User information for a Class B digital device This document is the property of: ORPAK SYSTEMS Ltd. ISRAEL FCC Warning Modifications not expressly approved by the manufacturer responsible could void the user’s authority to operate the equipment under FCC rules. THE FCC WANTS YOU TO KNOW: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential area. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician FCC Warning Modifications not expressly approved by the manufacturer responsible could void the user’s a…

Text truncated - open the document above for the full version.

To: Federal Communications Commission From: Shaike Raz Att: Reviewing Engineer Reference No: L95213.00 Date: 16 November 2010 Subject: Intermodulation Testing of FCC ID: W8F800922576 and FCC ID W8F819539370 Transmitters To Whom it may Concern, 1. The subject transmitters were operated simultaneously for intermodulation tests. 2. Both transmitters meet FCC Part 15 requirements when operating simultaneously. 3. Please let me know if you need any additional information. I.T.L (PRODUCT TESTING) Ltd. PRODUCT SAFETY, EMC & TELECOMS LAB. Bat-Sheva St., POB 87 LOD 71100 ISRAEL Tel. 972-8-9186100 Fax. 972-8-9153101 Email: [email protected], Web Site: http://www.itl.co.il Regards Shaike Raz EMC Laboratory Manager EMC Laboratory ITL (Product Testing) Ltd. Kfar Bin Nun/Lod Israel Tel: +972-8-918-6117 Fax: +972-8-915-3101 Email: [email protected] http://www.itl.co.il

REPLACE WITH OFFICIAL COMPANY LOGO / LETTERHEAD Date: 01.11. 10 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: W8F800922576 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: CONF APPENDIX OrPT Panel BlkDia.pdf CONF APPENDIX OrPT Panel PartsLst.pdf CONF APPENDIX OrPT Panel Schem.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Thank you, Signature: ______________ Printed Name: Gidi Segal Quality Assurance Director Orpak Systems Ltd.

Date: 01.11. 10 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Shaike Raz of I.T.L. (Product Testing) Ltd (ITL) to sign FORM 731 on our behalf for the following application: FCC ID: W8F800922576 Thank you, Gidi Segal Quality Assurance Director Orpak Systems Ltd. Tel: +972-3-577-6866 Fax: +972-3-579-6310 E-mail: [email protected] Website: www.orpak.com Fueling your business for success 3 Consider the environment - do you really need to print this email? CONFIDENTIAL!

REPLACE WITH OFFICIAL COMPANY LOGO / LETTERHEAD Date: 01.11.10 To Whom It May Concern We hereby authorize I.T.L. (Product Testing) Ltd (ITL) to act on our behalf regarding the FCC ID Certification Process for the following application: FCC ID: W8F800922576 Thank you, Signature: ______________ Printed Name: Gidi Segal Quality Assurance Director Orpak Systems Ltd.

Date: November 15, 2010 Ref: LMA Compliance Letter FCC To: Federal Communications Commission Subject: LMA compliance letter This letter introduces ORPAK Systems Ltd request to approve its OrPT wireless RF module according to FCC Limited Modular Approval procedure, and to demonstrate the means to control the module as required by the LMA procedure. The module OrPT (Payment Terminal), P/N 800922576, is a 13.56MHz wireless module manufactured by ORPAK Systems Ltd. The model consists of a plastic panel & metal back cover that use as closed enclosure consists of OrPT main PCB with a header for connection to the OrPT MiFare PCB that connect to a PCB antenna via harness, Keyboard, LCD, Barcode Reader, Card Reader and OrPT Interface PCB. This model is not sold separately, and is not installed in any units other then ORPAK's Products, and currently it is used in the following hosts: OrIC, P/N 8009380850 and OrIC8, P/N 800941505. Each of these hosts has various sub-configurations which differ from the main host only by software and/or extracted components/assemblies. See Orpak Systems declarations concerning additional OrIC and OrIC8 model variations. 1) Following is the list of OrIC, P/N 8009380850, model variations. OrIC/OrIT Main Configurations for FCC P/N Product Name 800938102 OrIT (E) 800938103 OrIC (E) 800938104 OrIT (2M) 800938105 OrIC (2M) 800938106 OrIT (4M) 800938107 OrIC (4M) 800938118 OrIT (E,WGT) 800938119 OrIC (E,WGT) 800938120 OrIT (2M,WGT) 800938121 OrIC (2M,WGT) 800938122 OrIT (4M,WGT) 800938123 OrIC (4M,WGT) 800938134 OrIT (E,PRN) 800938135 OrIC (E,PRN) OrIC/OrIT Main Configurations for FCC P/N Product Name 800938136 OrIT (2M,PRN) 800938137 OrIC (2M,PRN) 800938138 OrIT (4M,PRN) 800938139 OrIC (4M,PRN) 800938150 OrIT (E,WGT,PRN) 800938151 OrIC (E,WGT,PRN) 800938152 OrIT (2M,WGT,PRN) 800938153 OrIC (2M,WGT,PRN) 800938154 OrIT (4M,WGT,PRN) 800938155 OrIC (4M,WGT,PRN) 800938166 OrIT (E,DK) 800938167 OrIC (E,DK) 800938168 OrIT (2M, DK) 800938169 OrIC (2M, DK) 800938170 OrIT (4M, DK) 800938171 OrIC (4M, DK) 800938182 OrIT (E,WGT,DK) 800938183 OrIC (E,WGT,DK) 800938184 OrIT (2M, WGT,DK) 800938185 OrIC (2M, WGT,DK) 800938186 OrIT (4M, WGT,DK) 800938187 OrIC (4M,WGT, DK) 800938198 OrIT (E,PRN,DK) 800938199 OrIC (E, PRN,DK) 800938200 OrIT (2M, PRN,DK) 800938201 OrIC (2M, PRN,DK) 800938202 OrIT (4M, PRN,DK) 800938203 OrIC (4M, PRN,DK) 800938214 OrIT (E,WGT,PRN,DK) 800938215 OrIC (E,WGT,PRN,DK) 800938216 OrIT (2M,WGT,PRN,DK) 800938217 OrIC (2M,WGT,PRN,DK) 800938218 OrIT (4M,WGT,PRN,DK) 800938219 OrIC (4M,WGT,PRN, DK) 800938358 OrIT (O,E) 800938359 OrIC (O,E) OrIC/OrIT Main Configurations for FCC P/N Product Name 800938360 OrIT (O,2M) 800938361 OrIC (O,2M) 800938362 OrIT (O,4M) 800938363 OrIC (O,4M) 800938374 OrIT (O,E,WGT) 800938375 OrIC (O,E,WGT) 800938376 OrIT (O,2M,WGT) 800938377 OrIC (O,2M,WGT) 800938378 OrIT (O,4M,WGT) 800938379 OrIC (O,4M,WGT) 800938390 OrIT (O,E,PRN) 800938391 OrIC (O,E,PRN) 800938392 OrIT (O,2M,PRN) 800938393 OrIC (O,2M,PRN) 800938394 OrIT (O,4M,PRN) 800938395 OrIC (O,4M,PRN) 800938406 OrIT (O,E,WGT,PRN) 800938407 OrIC (O,E,WGT,PRN) 800938408 OrIT (O,2M,WGT,PRN) 800938409 OrIC (O,2M,WGT,PRN) 800938410 OrIT (O,4M,WGT,PRN) 800938411 OrIC (O,4M,WGT,PRN) 800938422 OrIT (O,E,DK) 800938423 OrIC (O,E,DK) 800938424 OrIT (O,2M, DK) 800938425 OrIC (O,2M, DK) 800938426 OrIT (O,4M, DK) 800938427 OrIC (O,4M, DK) 800938438 OrIT (O,E,WGT,DK) 800938439 OrIC (O,E,WGT,DK) 800938440 OrIT (O,2M, WGT,DK) 800938441 OrIC (O,2M, WGT,DK) 800938442 OrIT (O,4M, WGT,DK) 800938443 OrIC (O,4M,WGT, DK) 800938454 OrIT (O,E,PRN,DK) 800938455 OrIC (O,E, PRN,DK) OrIC/OrIT Main Configurations for FCC P/N Product Name 800938456 OrIT (O,2M, PRN,DK) 800938457 OrIC (O,2M, PRN,DK) 800938458 OrIT (O,4M, PRN,DK) 800938459 OrIC (O,4M, PRN,DK) 800938470 OrIT (O,E,WGT,PRN,DK) 800938471 OrIC (O,E,WGT,PRN,DK) 800938472 OrIT (O,2M,WGT,PRN,DK) 800938473 OrIC (O,2M,WGT,PRN,DK) 800938474 OrIT (O,4M,WGT,PRN,DK) 800938475 OrIC (O,4M,WGT,PRN, DK) 2) Following is the list of OrIC8, P/N 800941505, model variations. OrIC 8/ OrIT 8 Main Configurations for FCC P/N Name 800941002 OrIT 8 (E) 800941003 OrIC 8 (E) 800941004 OrIT 8 (2M) 800941005 OrIC 8 (2M) 800941006 OrIT 8 (4M) 800941007 OrIC 8 (4M) 800941008 OrIT 8 (8M) 800941009 OrIC 8 (8M) 800941018 OrIT 8 (E,WGT) 800941019 OrIC 8 (E,WGT) 800941020 OrIT 8 (2M,WGT) 800941021 OrIC 8 (2M,WGT) 800941022 OrIT 8 (4M,WGT) 800941023 OrIC 8 (4M,WGT) 800941024 OrIT 8 (8M,WGT) 800941025 OrIC 8 (8M,WGT) 800941034 OrIT 8 (E,PRN) 800941035 OrIC 8 (E,PRN) 800941036 OrIT 8 (2M,PRN) 800941037 OrIC 8 (2M,PRN) 800941038 OrIT 8 (4M,PRN) OrIC 8/ OrIT 8 Main Configurations for FCC P/N Name 800941039 OrIC 8 (4M,PRN) 800941040 OrIT 8 (8M,PRN) 800941041 OrIC 8 (8M,PRN) 800941050 OrIT 8 (E,WGT,PRN) 800941051 OrIC 8 (E,WGT,PRN) 800941052 OrIT 8 (2M,WGT,PRN) 800941053 OrIC 8 (2M,WGT,PRN) 800941054 OrIT 8 (4M,WGT,PRN) 800941055 OrIC 8 (4M,WGT,PRN) 800941056 OrIT 8 (8M,WGT,PRN) 800941057 OrIC 8 (8M,WGT,PRN) 800941066 OrIT 8 (E,DK) 800941067 OrIC 8 (E,DK) 800941068 OrIT 8 (2M, DK) 800941069 OrIC 8 (2M, DK) 800941070 OrIT 8 (4M, DK) 800941071 OrIC 8 (4M, DK) 800941072 OrIT 8 (8M, DK) 800941073 OrIC 8 (8M, DK) 800941082 OrIT 8 (E,WGT,DK) 800941083 OrIC 8 (E,WGT,DK) 800941084 OrIT 8 (2M, WGT,DK) 800941085 OrIC 8 (2M, WGT,DK) 800941086 OrIT 8 (4M, WGT,DK) 800941087 OrIC 8 (4M,WGT, DK) 800941088 OrIT 8 (8M, WGT,DK) 800941089 OrIC 8 (8M,WGT, DK) 800941098 OrIT 8 (E,PRN,DK) 800941099 OrIC 8 (E, PRN,DK) 800941100 OrIT 8 (2M, PRN,DK) 800941101 OrIC 8 (2M, PRN,DK) 800941102 OrIT 8 (4M, PRN,DK) 800941103 OrIC 8 (4M, PRN,DK) 800941104 OrIT 8 (8M, PRN,DK) 800941105 OrIC 8 (8M, PRN,DK) 800941114 OrIT 8 (E,WGT,PRN,DK) OrIC 8/ OrIT 8 Main Configurations for FCC P/N Name 800941115 OrIC 8 (E,WGT,PRN,DK) 800941116 OrIT 8 (2M,WGT,PRN,DK) 800941117 OrIC 8 (2M,WGT,PRN,DK) 800941118 OrIT 8 (4M,WGT,PRN,DK) 800941119 OrIC 8 (4M,WGT,PRN, DK) 800941120 OrIT 8 (8M,WGT,PRN,DK) 800941121 OrIC 8 (8M,WGT,PRN, DK) 800941258 OrIT 8 (O,E) …

Text truncated - open the document above for the full version.

To: Federal Communications Commission From: Shaike Raz Att: Reviewing Engineer Reference No: L95210.00 Date: 15 November 2010 Subject: FCC Certification for Orpak Systems, Orpak Payment terminal (OrPT) M/N OrPT Panel, P/N 800922576 FCC ID: W8F800922576 To Whom it may Concern, 1. We are submitting an application for Limited Modular approval on behalf of Orpak systems Ltd. for the above subject device placed in the hosts whose details are submitted with this application. 2. Exploratory radiated emission tests was performed on the host configurations (OrIC and OrIC8) in order to determine the “worst case” host. Full testing was performed on the “worst case” host (OrIC8). 3. Exhibits concerning all hosts under this application are being submitted. 4. Please let me know if you need any additional information. I.T.L (PRODUCT TESTING) Ltd. PRODUCT SAFETY, EMC & TELECOMS LAB. Bat-Sheva St., POB 87 LOD 71100 ISRAEL Tel. 972-8-9186100 Fax. 972-8-9153101 Email: [email protected], Web Site: http://www.itl.co.il Regards Shaike Raz EMC Laboratory Manager EMC Laboratory ITL (Product Testing) Ltd. Kfar Bin Nun/Lod Israel Tel: +972-8-918-6117 Fax: +972-8-915-3101 Email: [email protected] http://www.itl.co.il

The OrPT (see Figure 1‐1) represents a new generation of terminals designed to address new applications at the forecourt. This versatile payment terminal provides several services besides its core function of payment and fueling authorization. The OrPT is encased in a sealed housing designed to sustain the harsh environment of a gas station. Its modular design enables adding features as requested, and can be upgraded as new capabilities are developed. Figure 1-1. OrPT in Orpak OrIC Pedestal – General View To perform as a payment terminal, the OrPT is equipped with a graphic LCD and Keyboard on its front panel. A magnetic card reader Barcode Reader and contactless MiFare card reader are also included. These payment means enable the OrPT to accept all common fueling authorization methods in home-base stations such as fueling cards, contact-less tags and others. Beside the card / tag readers, the front panel includes functional keys and a display panel. The context sensitive keys and the messages on the panel enable the user interaction with the module, and navigation between applications. The OrPT interfaces with the Station Controller on two types of communication: • RS-485 • TCP/IP over Ethernet

Date: 01.11.2010 To Whom It May Concern I hereby declare that there is no tune-up procedure for: FCC ID: W8F800922576 Thank you, Gidi Segal Quality Assurance Director Orpak Systems Ltd. Tel: +972-3-577-6866 Fax: +972-3-579-6310 E-mail: [email protected] Website: www.orpak.com Fueling your business for success 3 Consider the environment - do you really need to print this email? CONFIDENTIAL!

R.F Exposure/Safety for OrPT Panel and WGT Transmitters The typical placement of the Wireless Gateway Terminal is either wall mounted or inside an Orpak Island Fuel Controller. The placement of the Orpak Payment Terminal is inside an Orpak Island Fuel Controller. The typical distance between the two transmitters when placed in an Orpak Island Fuel Controller and the user in the worst case application, is <20 cm . Calculation of Maximum Permissible Exposure (MPE) 2 1 cm mW MHz is: Based on Section 1.1307(b)(1) Requirements (a) FCC limits at 2440 Using table 1 of Section 1.1310 limgeneral population/uncontrolled exposures, (b) ength at 3 meters is 51.6 dBμV/m, his is more than 5 orders of magnitude below the 2.4 GHz transmitter and therefore it is er density produced by the 2.4 GHz transmitter is: itted Power 5.07 mw (Peak) worst case (c) The (d) This is b it for the above level is an average over 30 minutes. For the 13.56 MHz transmitter (OrPT), the field str interpolated to 20 cm is 74.1 dBμV/m. Converting to Power Density: 22 cmm 66 100066.010066.0/1.74 mWw mVdB −− ×=×=μ T negligible. (b) The pow P t - Transm G T - Antenna Gain, 0 dBi = 1 (Numeric) R- Distance from Transmitter using 20 cm peak power density (time averaging) is : 2 4R GP S tt π = 22 )20(4 cmπ 3 100.1 107.5 mW S p − ×= × = elow the FCC limit.

DATE: 16 November 2010 I.T.L. (PRODUCT TESTING) LTD. FCC Radio Test Report for Orpak Systems Ltd. Equipment under test: Orpak Payment Terminal (OrPT) OrPT Panel Written by: _____________________________ Test Report E95215.01 Orpak Systems Ltd. Page 1 of 34 D. Shidlowsky, Documentation Approved by: For/__________________________ A. Sharabi, Test Engineer Approved by: _____________________________ I. Raz, EMC Laboratory Manager This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. FCC ACC M Ver 1.1 05Mayl 2000 Test Report E95215.01 Orpak Systems Ltd. Page 2 of 34 FCC ACC M Ver 1.1 05Mayl 2000 Measurement/Technical Report for Orpak Systems Ltd. Orpak Payment Terminal (OrPT) OrPT Panel FCC ID: W8F800922576 This report concerns: Original Grant: X Class I change: Class II change: Equipment type: Part 15 Low Power Communication Device Transmitter 47CFR15 Section 15.225 Measurement procedure used is ANSI C63.4-2003. Application for Certification Applicant for this device: prepared by: (different from "prepared by") Ishaishou Raz Gideon Segal ITL (Product Testing) Ltd. Orpak Systems Ltd. Kfar Bin Nun 31 Lechi St. D.N. Shimshon 99780 P.O.B. 1461 Israel Bnei-Brak 5114 e-mail [email protected] Israel Tel: +972- 3 - 577 - 6868 Fax: +972- 6 - 579 - 6310 e-mail: gidi@orpak .com TABLE OF CONTENTS 1. GENERAL INFORMATION ------------------------------------------------------------------------------- 5 1.1 Administrative Information ................................................................................. 5 1.2 List of Accreditations ......................................................................................... 6 1.3 Product Description ........................................................................................... 7 1.4 Test Methodology .............................................................................................. 7 1.5 Test Facility ....................................................................................................... 7 1.6 Measurement Uncertainty ................................................................................. 7 2. SYSTEM TEST CONFIGURATION --------------------------------------------------------------------- 8 2.1 Justification ........................................................................................................ 8 2.2 EUT Exercise Software ..................................................................................... 8 2.3 Special Accessories .......................................................................................... 8 2.4 Equipment Modifications ................................................................................... 9 2.5 Configuration of Tested System ........................................................................ 9 3. TEST SET-UP PHOTOS ----------------------------------------------------------------------------------10 4. CONDUCTED EMISSION DATA -----------------------------------------------------------------------11 4.1 Test Specification ............................................................................................ 11 4.2 Test Procedure ................................................................................................ 11 4.3 Test Results .................................................................................................... 11 4.4 Test Instrumentation Used, Conducted Measurement ................................... 16 5. FIELD STRENGTH OF FUNDAMENTAL ------------------------------------------------------------17 5.1 Test Specification ............................................................................................ 17 5.2 Test Procedure ................................................................................................ 17 5.3 Test Results .................................................................................................... 17 5.4 Test Instrumentation Used, Field Strength of Fundamental ........................... 19 6. SPURIOUS RADIATED EMISSION, 9 KHZ – 30 MHZ -------------------------------------------20 6.1 Test Specification ............................................................................................ 20 6.2 Test Procedure ................................................................................................ 20 6.3 Test Results .................................................................................................... 20 6.4 Test Instrumentation Used, Radiated Measurements .................................... 21 6.5 Field Strength Calculation ............................................................................... 21 7. SPURIOUS RADIATED EMISSION 30 – 1000 MHZ ----------------------------------------------22 7.1 Test Specification ............................................................................................ 22 7.2 Test Procedure ................................................................................................ 22 7.3 Test Results .................................................................................................... 22 7.4 Test Instrumentation Used, Radiated Measurements .................................... 23 7.5 Field Strength Calculation ............................................................................... 23 8. FREQUENCY TOLERANCE ----------------------------------------------------------------------------24 8.1 Test Specification ............................................................................................ 24 8.2 Test Procedure ................................................................................................ 24 8.3 Test Results .................................................................................................... 24 8.1 Test Instrumentation Used, Frequency Tolerance .......................................... 25 9. APPENDIX A - CORRECTI…

Text truncated - open the document above for the full version.