WONSA91004000SA TAG 915 MHz

Precyse Technologies, Inc. Date: 12 June 2011 Page 1 of 9 P.W.Wireless Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Document No.:20110706-1 Revision: 1.1 Badge tag 915MHz User Manual Release Date: ‏0383/813// Prepared by: Lior Bilia Distribution (Check all appropriate): [ ] Precyse Only [ ] Project Team Only [ ] Customer and Supplier C:\hardwareWS\Production\PD-915\Badge Tag\Human\Documents\SA91004100 user manual.docx Precyse Technologies, Ltd.. Date: 27 June 2012 Page 2 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Revision Record Rev. Effective Date Description 1.0 1.1 30/8/2011 Updated part number, model number and product name. Reference documents # Doc # Description 1 Precyse Technologies, Ltd.. Date: 27 June 2012 Page 3 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 TABLE OF CONTENTS Section/Title Page Introduction ........................................................................................................... 4 Regulatory Information/disclaimers ....................................................................... 4 Product description ............................................................................................... 6 AGPS tag: .......................................................................................................... 6 Technical Parameters ........................................................................................... 6 Models: .............................................................................................................. 6 Performance: ..................................................................................................... 6 Communication: ................................................................................................. 6 Electrical: ........................................................................................................... 6 Environmental: ................................................................................................... 7 Block diagram ....................................................... Error! Bookmark not defined. Precyse Technologies, Ltd.. Date: 27 June 2012 Page 4 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Introduction This document provides you with technical support information, and sources for additional product information. Regulatory Information/disclaimers Installation and use of this Wireless Radio device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The Manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, of the substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Instructions concerning human exposure to radio frequency electromagnetic fields: To comply with FCC Section 1.307 (b) (1) for human exposure to radio frequency electromagnetic fields, implement the following instruction: A distance of at least 20cm. between the equipment and all persons should be maintained during the operation of the equipment. The minimum distance will be determined after testing has been completed. This document is confidential and proprietary. No part of this document may be reproduced, stored, or transmitted in any form or by any means without prior written permission from Precyse technologies Inc. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation." Precyse Technologies, Ltd.. Date: 27 June 2012 Page 5 of 9 P.W.Precyse WirelessLtd. Rosh Ha’ayin 48092 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 The FCC Wants You to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: a) Reorient or relocate the receiving antenna. b) Increase the separation between the equipment and receiver. c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. d) Consult the dealer or an experienced radio/TV technician. FCC Warning Modifications not expressly approved by the manufacturer could void the user authority to operate the equipment under FCC Rules. Precyse Technologies, Ltd.. Date: 27 June 2012 Page 6 of 9 P.W.Precys…

Text truncated - open the document above for the full version.

Ha’amal 11, Park Afek Rosh Ha’ayin Israel 48092 To: Tim co Engineering Inc. To Whom It May Concern We hereby authorize Mr. Shaike Raz of I.T.L. (Product Testin g) Ltd (I TL) to act on our behalf regarding the FCC ID Certific ation Process for the following appli cation: FCC ID: WONSA91004000 Tha nk you, Lior Bilia Hardware engineer Precyse Technologies Tel: 972-3-9227093 Mobile: 972-54-2 467600 Fax: 972-3-9227515

Precyse Technologies 100 Ashford Center North Suite 360 Atlanta, GA 30338 To: Timco Engineering Inc. To Whom It May Concern We hereby authorize Mr. Shaike Raz of I.T.L. (Product Testing) Ltd (ITL) to sign FORM 731 on our behalf for the following application: FCC ID: WONSA91004000 Thank you, Lior Bilia HW engineer Precyse technologies LTD Tel: 972-3-9227093 Mobile: 972-54-2467600 Fax: 972-3-9227515

P.O. Box 3032 Petah Tikva, Israel 49130 Tel: +972 (0)3 9227093 Fax: +972 (0)3 9227515 Fede ral Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of F CC ID: WONSA91004000. Pur suant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential t reatment of information accompanying this appl ication as outlined below: CONF APPENDIX S A91004000 BlkDia.pdf CONF APPENDIX S A91004000 Sche m.pdf CONF APPENDIX S A91004000 PartsLst.pdf The a bove materials contain trade s ecrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the a pplicant and provide unjustified be ne fits to its competitors. The a pplicant underst ands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this appl ication. Sincerely, Lior Bilia Hardware engineer 1 www.PrecyseTech.com

One Stamford Plaza, 263 Tresser Blvd Suite 957, Stamford, CT 06901 Tel: 203.564.1526 attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: The SA91004000 FCC ID: WONSA91004000 and label is so small that it cannot include the statement specified in FCC Part 15 Sub-part A, Section 15.19 (a) (3) “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation." Due to this reason, we are using the provisions of Part 15 Sub-part A, Section 15.19 (a) (5) and this testament appears in a prominent location in the user manual. Please contact me if there is any information you may need. Sincerely, Lior Bilia HW engineer Precyse Technologies Inc Tel: 972-3-9227093 Mobile: 972-54-2467600 Fax: 972-3-9227515

Theory of operation The SAT method of communication is synchronized event based reporting, the SAT spends most of its time in low power sleep mode. When an event happens, the SAT sends a report to the base station. In order to avoid packet collisions and associated detection methods, the system uses a synchronous protocol, that is, An SAT can transmit data only after receiving a synchronization signal from the base station

attn: Reviewing Engineer Fede ral Communications Commission 7435 Oakland Mills Roa d Columbia, MD 21046 To Whom It May Concern: Precyse Technologies 100 Ashford Center North Suite 360 Atla nta, GA 30338 I hereby declare that there is no tune-up procedure for FCC ID: WONSA91004000. Please c ontact me i f there is any infor mation you may need. Sincerely, Lior Bilia HW e ng ineer Precyse T echnologies Inc Tel: 972-3- 9227093 Mobile: 972-54-2467600 Fax: 972-3- 9227515

Test Report E112210.00 Precyse Technologies Inc. Page 1 of 44 FCC ACC M Ver 1.1 05Mayl 2000 DATE: 28 June 2012 I.T.L. (PRODUCT TESTING) LTD. FCC Radio Test Report for Precyse Technologies Inc. Equipment under test: Badge Tag 915MHz E3-HuTag-AGPS Written by: _____________________________ I. Smilansky, Documentation Approved by: _____________________________ I. Siboni, Test Engineer Approved by: _____________________________ I. Raz, EMC Laboratory Manager This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. Test Report E112210.00 Precyse Technologies Inc. Page 2 of 44 FCC ACC M Ver 1.1 05Mayl 2000 Measurement/Technical Report for Precyse Technologies Inc. Badge Tag 915MHz E3-HuTag-AGPS FCC ID: WONSA91004000 This report concerns: Original Grant: X Class I Change: Class II Change: Equipment type: Digital Transmission System Limits used: 47CFR15 Section 15.247 Measurement procedure used is KDB 558074 D01 18 January 2012 and ANSI C63.4-2003. Application for Certification Applicant for this device: prepared by: (different from "prepared by") Ishaishou Raz Lior Bilia ITL (Product Testing) Ltd. Precyse Technologies Ltd. Kfar Bin Nun 94 Em Hamoshavot St. D.N. Shimshon 99780 Petach Tikva 49527 Israel Israel e-mail [email protected] Tel: +972-3- 922-7093 Fax: +972-3- 922-7515 e-mail: [email protected] Test Report E112210.00 Precyse Technologies Inc. Page 3 of 44 FCC ACC M Ver 1.1 05Mayl 2000 TABLE OF CONTENTS 1. GENERAL INFORMATION ------------------------------------------------------------------------------- 5 1.1 Administrative Information ................................................................................. 5 1.2 List of Accreditations ......................................................................................... 6 1.3 Product Description ........................................................................................... 7 1.4 Test Methodology .............................................................................................. 7 1.5 Test Facility ....................................................................................................... 7 1.6 Measurement Uncertainty ................................................................................. 7 2. SYSTEM TEST CONFIGURATION --------------------------------------------------------------------- 8 2.1 Justification ........................................................................................................ 8 2.2 EUT Exercise Software ..................................................................................... 8 2.3 Special Accessories .......................................................................................... 8 2.4 Equipment Modifications ................................................................................... 8 2.5 Configuration of Tested System ........................................................................ 8 3. TEST SETUP PHOTOGRAPH --------------------------------------------------------------------------- 9 4. 6DB MINIMUM BANDWIDTH --------------------------------------------------------------------------- 10 4.1 Test Specification ............................................................................................ 10 4.2 Test Procedure ................................................................................................ 10 4.3 Test Results..................................................................................................... 10 4.4 6dB Minimum Bandwidth Test Equipment Used ............................................. 13 5. RADIATED MAXIMUM POWER OUTPUT ----------------------------------------------------------- 14 5.1 Test Specification ............................................................................................ 14 5.2 Test Procedure ................................................................................................ 14 5.3 Test Results..................................................................................................... 15 5.4 Radiated Maximum Power Output Test Equipment Used. .............................. 18 6. BAND EDGE ------------------------------------------------------------------------------------------------- 19 6.1 Test Specification ............................................................................................ 19 6.2 Test Procedure ................................................................................................ 19 6.3 Test Results..................................................................................................... 19 6.4 Band Edge Test Equipment Used. .................................................................. 21 7. SPURIOUS RADIATED EMISSION, 9 KHZ – 30 MHZ ------------------------------------------- 22 7.1 Test Specification ............................................................................................ 22 7.2 Test Procedure ................................................................................................ 22 7.3 Test Results..................................................................................................... 22 7.4 Spurious Radiated Emission, 9 kHz – 30 MHz Test Equipment Used ............ 23 7.5 Field Strength Calculation ............................................................................... 23 8. SPURIOUS RADIATED EMISSION 30 MHZ – 10 GHZ ------------------------------------------ 24 8.1 Test Specification ............................................................................................ 24 8.2 Test Procedure ................................................................................................ 24 8.3 Test Results..................................................................................................... 25 8.4 Spurious Radiated Emission 30 MHz – 10 GHz, Test Equipment Used ......... 28 8.5 Field Streng…

Text truncated - open the document above for the full version.