WP3KP141PG2NRemote keypad

D-303015 KP-140 PG2, KP-141 PG2 Installation Instructions 1 KP-140 PG2/KP-141 PG2 Portable Remote Wireless 2-Way Keypad User’s Guide 1. INTRODUCTION KP-140 PG2 and KP-141 PG2 are 2-way PowerG wireless keypads for the PowerMaster family control panels. The KP-141 PG2 is the same as the KP-140 PG2 but also includes a built-in proximity RFID tag reader. Both keypads enable most common everyday user functions:  Arm and Disarm the alarm system.  Initiate Emergency, Fire and Panic alarms.  Control X-10 devices and PGM output (not to be enabled in UL Listed product).  Perform one of the AUX (auxiliary) predefined functions.  Review system Status. When authorization is required, for example, to arm or disarm the system, the user can enter his PIN Code via the built-in numerical keypad or alternatively present a valid proximity tag to the built-in tag reader (only with KP-141PG2) located at "N" in Figure 1. In addition, the KP-140 PG2/KP-141 PG2 keypad supports panels featuring Partitions. Partitioning allows you to have up to three controllable areas; each partition can be armed and disarmed independently regardless of the status of the other two partitions by the same or different users (see buttons marked "E" in Figure 1). The keypads can be wall mounted using the supplied bracket or be used as portable units. For compliance with various international standards, the keypads are equipped with two tamper switches that can be configured to detect when the cover of the battery compartment is removed or when the unit is removed from its mounting bracket. Note: For UL Listed Product, unit is not intended to be portable. Other features of the KP-140 PG2/KP-141 PG2 keypad include:  Status, alarm memory, trouble and Ready / Not-Ready indications.  Automatic reporting of low battery voltage.  Keypad back lighting.  Exit/entry beeps  Tag reader can also be used to enroll proximity tags into the panel.  Long-life 4-5 years battery life expectancy (for typical use), 3 VDC lithium battery. Note: For UL Listed product, the proximity feature may only be used to arm or disarm the system. Note: For UL Listed product, Models KP-140 PG2 and KP-141 PG2 are for Supplemental Use only. B A C D E F G H I J K L M N A. ARM HOME H. AUX / ENROLLMENT B. ARM AWAY I. EMERGENCY ALARM C. DISARM J. FIRE ALARM D. X-10 / PGM K. PANIC ALARM E. PARTITION SELECTION L. BUZZER INDICATOR F. ARM INSTANT M. LED INDICATOR G. STATUS / ESCAPE N. TAG READER Figure 1 - External View 2. INSTALLATION 2.1 Mounting and Battery Replacement 3 A 1 2 1. Drill 2 holes in mounting surface, insert wall anchors and fasten the bracket with 2 screws. 2. Place the "Visual Indications" sticker within the frame. 3. Slide the keypad into the bracket. A. Magnet (activates back tamper when bracket is removed from the wall). Figure 2 - Mounting 2 1 A 1. Slide out the cover. 2. Replace the battery (verify proper polarity) and close the cover. A. Battery compartment tamper switch Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to manufacturer's instructions. Figure 3 - Battery Replacement 2.2. ENROLLMENT Refer to the PowerMaster panel's Installer Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu a general description of which is provided in the following flow chart. Step 1 Step 2 Step 3 Step 4 Enter the Installer menu and select “02:ZONES/DEVICES” Select "ADD NEW DEVICE" See Note 1 Enroll the keypad by holding the button and release it as soon as the yellow LED lights. Alternatively, enter the device ID (printed on the back of the keypad) Select the desired keypad Number for the new keypad See Note 2      MODIFY DEVICES ID No. 370-XXXX K06:Keypad ENTR ID:XXX-XXXX ENROLL NOW or ADD NEW DEVICES02:ZONES/DEVICES 2 D-303015 KP-140 PG2, KP-141 PG2 Installation Instructions Step 5 Step 6 Step 7 Step 8 Configure Location parameter Enter PARTITIONS. See Note 3 Assign partitions to the keypad by pressing the , and buttons on the panel Continue to section 2.3     means scroll and select Notes: 1. If the keypad is already enrolled, you can configure the keypad parameters and assign partitions via the “Modify Devices” option – see Step 2. 2. The first three digits of the Device ID No. "370-XXXX" refer to KP-140 PG2. For KP-141 PG2, the first three digits of the device ID No. are "371-XXXX". 3. PARTITIONS will appear only if PARTITIONING was previously enabled in the panel (for further details, see "Partitioning" in the PowerMaster Installer Guide). 2.3. Configuring the Keypad Parameters Enter the menu and follow the configuration instructions for the KP-140 PG2/KP-141 PG2 keypad as described in the following table. Option Configuration Instructions Here you determine which of the two tampers (i.e. battery compartment cover or all of the tampers) will be active. Optional settings: Disabled (default); all tampers; Battery cover. Note: For UL Listed product, set to “all tampers”. Here you determine whether or not the control panel will monitor supervision messages sent by the keypad or not (see Note). Optional settings: ON (default) or OFF. Notes: 1. Every 5 minutes the keypad performs a communication test session with the control panel (i.e. "Supervision signal) to check the integrity and quality of the Radio link. If the keypad does not report a supervision signal at least once within a predefined time window, a “MISSING” trouble alert is initiated. Therefore, if you intend to take the keypad out of the protected premises you must switch the Supervision OFF to avoid the trouble alert. 2. For UL Listed product, set to “ON”. Here you determine whether the keypad will sound the exit and entry beeps, or not, or whether the keypad will sound the beeps only when the system is armed AWAY and not when it is armed HOME. Optional settings: ON; OFF (default) and OFF @ Home. Note: For UL Listed product, the sounder cannot be used as the only annunciator for the system. Here y…

Text truncated - open the document above for the full version.

Rev 11/20/07 To: Timco Engineering, Inc. To Whom It May Concern We the undersigned, hereby authorize Mr. Michael Nikishin of Hermon Laboratories to act on behalf of Visonic Ltd. in all manners relating to application for certification of FCC ID:WP3KP141PG2N, IC:1467C-KP141PG2N. Any and all acts carried out by Hermon Laboratories, on our behalf shall have the same legal authority as acts of our own. This authorization is valid until further written notice from Visonic Ltd. Sincerely, Arik Elshtein

Rev 11/20/07 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID:WP3KP141PG2N. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block diagram KP-141_BlkDia Schematic diagrams KP-141_Schem, KP-141_PROX_Schem Operational description KP-141_OpDes The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Arik Elshtein

Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 1 of 4 EXTERNAL PHOTOGRAPHS This document contains 3 photographs Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 2 of 4 Photograph No.1 Remote keypad front view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 3 of 4 Photograph No.2 Remote keypad rear side view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 4 of 4 Photograph No.3 Remote keypad rear side with cover removed

Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 1 of 1 Label of KP-141 PG remote keypad Label location Label with FCC ID:WP3KP141PG2N and IC:1467C-KP141PG2N will be located at the rear side panel. The statement according to FCC part 15 §15.19(a)(3) is placed in User’s Guide, page 4 (Application exhibit KP-141_UserMan).

Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 1 of 12 INTERNAL PHOTOGRAPHS This document contains 11 photographs Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 2 of 12 Photograph No.1 Remote keypad internal view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 3 of 12 Photograph No.2 Remote keypad internal view, second side Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 4 of 12 Photograph No.3 Main PCB front view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 5 of 12 Photograph No.4 RF modules close view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 6 of 12 Photograph No.5 RF modules close side view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 7 of 12 Photograph No.6 Main PCB with RF modules removed Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 8 of 12 Photograph No.7 Main PCB second side view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 9 of 12 Photograph No.8 RF module Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 10 of 12 Photograph No.9 RF module second side view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 11 of 12 Photograph No.10 Proximity module front view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 12 of 12 Photograph No.11 Proximity module second side view

Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 1 of 1 RF exposure information according to FCC CFR 47 part 15, §15.247(i) and RSS-102 The remote keypad may be wall mounted or used as a portable device operating in 912.750 – 919.106 MHz band. It is equipped with an integrated internal antenna. Maximum measured transmitter power: Pout conducted Maximum antenna gain, dBi Pout EIRP dBm mW dBm mW 20.08 101.9 -3 17.08 51 According to the manufacturer’s declaration in every 6 min the device transmits 2 supervision messages of 6 ms duration each and 2 messages following a key press of 10 ms duration each. Total duration is 32 ms. The duty cycle is 9 x10 –5 . Maximum conducted power is 101.9 mW. Equivalent averaged conducted power is 101.9 mW x duty cycle = 101.9 mW x 9 x10 –5 = 917 x10 –5 mW. According to KDB 447498 D01 v05r02 and RSS-102 section 2.5.1 the device is excluded from SAR evaluation.

Hermon Laboratories Ltd. Harakevet Industrial Zone, Binyamina 30500, Israel Tel. +972-4-6288001 Fax. +972-4-6288277 E-mail: [email protected] Page 1 of 85 Report ID: VISRAD_FCC_IC.25007.docx Date of Issue: 23-Jun-14 ELECTRICAL TESTING 0839.01 TEST REPORT ACCORDING TO: FCC 47CFR part 15 subpart C § 15.247 (FHSS), RSS-210 issue 8 Annex 8 FOR: Visonic Ltd. Remote Keypad 1) Model: KP-140 PG2 (915) FCC ID:WP3KP140PG2N IC:1467C-KP140PG2N 2) Model: KP-141 PG2 (915) FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N This report is in conformity with ISO/ IEC 17025. The "A2LA Accredited" symbol endorsement applies only to the tests and calibrations that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: VISRAD_FCC_IC.25007.docx Date of Issue: 23-Jun-14 Page 2 of 85 Table of contents 1 Applicant information ..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details .................................................................................................................................................................... 3 5 Tests summary .............................................................................................................................................................. 4 6 EUT description ............................................................................................................................................................. 5 6.1 General information ....................................................................................................................................................... 5 6.2 Test configuration .......................................................................................................................................................... 5 6.3 Changes made in the EUT ............................................................................................................................................ 5 6.4 EUT positions during testing ......................................................................................................................................... 6 6.5 Transmitter characteristics ............................................................................................................................................ 7 7 Transmitter tests according to 47CFR part 15 subpart C and RSS-210 Annex 8 requirements ................................... 8 7.1 20 dB bandwidth ........................................................................................................................................................... 8 7.2 Carrier frequency separation ....................................................................................................................................... 12 7.3 Number of hopping frequencies .................................................................................................................................. 15 7.4 Average time of occupancy ......................................................................................................................................... 19 7.5 Peak output power ...................................................................................................................................................... 23 7.6 Band edge radiated emissions .................................................................................................................................... 35 7.7 Field strength of spurious emissions ........................................................................................................................... 40 7.8 Antenna requirements ................................................................................................................................................. 71 8 APPENDIX A Test equipment and ancillaries used for tests ....................................................................................... 72 9 APPENDIX B Measurement uncertainties ................................................................................................................... 73 10 APPENDIX C Test laboratory description ................................................................................................................... 74 11 APPENDIX D Specification references ....................................................................................................................... 74 12 APPENDIX E Test equipment correction factors ......................................................................................................... 75 13 APPENDIX F Abbreviations and acronyms ................................................................................................................. 85 Report ID: VISRAD_FCC_IC.25007.docx Date of Issue: 23-Jun-14 Page 3 of 85 1 Applicant information Client name: Visonic Ltd. Address: 24 Habarzel street, Tel Aviv 69710, Israel Telephone: +972 3 645 6714 Fax: +972 3645 6788 E-mail: [email protected] Contact name: Mr. Arick Elshtein 2 Equipment under test attributes Product name: Wireless remote keypad Product type: Transceiver Model: KP141 PG2 Serial number: 3913557900 Cataloque number: 0-101843 Hardware version: 90-204024 Software release: JS-701795 PCB number: 8-303107 Receipt date 17-Oct-13 3 Manufacturer information Manufacturer name: Visonic Ltd. Address: 24 Habarzel street, Tel Aviv …

Text truncated - open the document above for the full version.

Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 1 of 10 SETUP PHOTOGRAPHS This document contains 9 photographs Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 2 of 10 Photograph No.1 Setup for spurious emission field strength measurements in the anechoic chamber below 30 MHz Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 3 of 10 Photograph No.2 Setup for hopping frequencies and spurious emission field strength measurements in the anechoic chamber in 30 – 1000 MHz range Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 4 of 10 Photograph No.3 Setup for spurious emission field strength measurements in the anechoic chamber above 1000 MHz range Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 5 of 10 Photograph No.4 Setup for spurious emission field strength measurements in the anechoic chamber, EUT close view Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 6 of 10 Photograph No.5 Setup for carrier field strength measurements at the OATS in 30 – 1000 MHz range, EUT in X-axis position Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 7 of 10 Photograph No.6 Setup for carrier field strength measurements at the OATS in 30 – 1000 MHz range, EUT in Y-axis position Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 8 of 10 Photograph No.7 Setup for carrier field strength measurements at the OATS in 30 – 1000 MHz range, EUT in Z-axis position Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 9 of 10 Photograph No.8 Setup for OBW measurements Visonic Ltd. FCC ID:WP3KP141PG2N IC:1467C-KP141PG2N Page 10 of 10 Photograph No.9 Setup for band edge emissions and hopping parameters measurements