X4D-SC-1SYSTEM TABLET CONTROLLER

INSTRUCTIONS System Tablet Controller SC-1 Labels and Symbols1 Important Information — Please Read Before Use6 Chapter 1 Checking the Package Contents13 Chapter 2 Nomenclature and Functions15 Chapter 3 Installation and Connection23 Chapter 4 Inspection53 Chapter 5 Operation59 Chapter 6 Reprocessing, Storage, and Disposal65 Chapter 7 Battery pack Replacement75 Chapter 8 Troubleshooting79 Appendix83 Contents i SC-1 INSTRUCTION MANUAL Contents Labels and Symbols .......................................................................................................... 1 Important Information — Please Read Before Use ......................................................... 6 Intended use .......................................................................................................................... 6 Instruction manual ................................................................................................................. 6 Instrument compatibility ......................................................................................................... 7 Repair and modification ......................................................................................................... 7 Signal words .......................................................................................................................... 7 Precautions ............................................................................................................................ 8 Chapter 1 Checking the Package Contents ....................................... 13 1.1Checking the package contents ........................................................................... 13 Chapter 2 Nomenclature and Functions ............................................ 15 2.1Symbols and descriptions ..................................................................................... 15 2.2Tablet ....................................................................................................................... 16 2.3Cradle ...................................................................................................................... 20 2.4Battery Pack ............................................................................................................ 22 Chapter 3 Installation and Connection ............................................... 23 3.1Precautions for installation and connection ....................................................... 23 3.2Installation workflow .............................................................................................. 24 3.3Mounting the cradle ............................................................................................... 25 Mounting the cradle ............................................................................................................. 25 3.4Connection to the power supply ........................................................................... 26 Connection to the power supply .......................................................................................... 27 3.5Docking the tablet .................................................................................................. 28 Docking the tablet ................................................................................................................ 28 3.6Creating an account ............................................................................................... 30 Creating an administrator account ....................................................................................... 30 Creating a standard user account ....................................................................................... 37 Deleting the default user account ........................................................................................ 37 3.7Setting the system locale ...................................................................................... 40 3.8Setting the language and time zone ..................................................................... 45 Setting the time zone ........................................................................................................... 45 Setting the language for an administrator account .............................................................. 46 Language settings for a standard user account .................................................................. 52 ii Contents SC-1 INSTRUCTION MANUAL Chapter 4 Inspection ............................................................................ 53 4.1Precautions for inspection .................................................................................... 53 4.2Inspection workflow ............................................................................................... 54 4.3Checking if the cradle is properly mounted on the system control arm ........... 55 4.4Checking if the tablet is docked correctly in the cradle ..................................... 55 4.5Power on ................................................................................................................. 55 4.6Checking the battery level and power supply ...................................................... 56 4.7Sleep mode ............................................................................................................. 57 Chapter 5 Operation ............................................................................. 59 5.1Precautions for operation ...................................................................................... 59 5.2Operation workflow ................................................................................................ 60 5.3Adjusting the tablet position ................................................................................. 61 5.4Charging .................................................................................................................. 62 5.5Power off ........................…

Text truncated - open the document above for the full version.

FCC ID: X4D-SC-1 Page: 1 / 49 Report No.: T200205D04-SF Rev.: 00 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group FCC TEST REPORT for SYSTEM TABLET CONTROLLER Model Name: SC-1 Issued to: ADLINK TECHNOLOGY INC. 9F, No.166, Jian Yi Rd., Zhonghe Dist., New Taipei City, 235 Taiwan Issued by Compliance Certification Services Inc. Wugu Lab. No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. (R.O.C.) Issued Date: 2020/05/26 Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Note: This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Page: 2 / 49 Report No.: T200205D04-SF Rev.: 00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 2020/5/26 Initial Issue ALL Edison Hu Page: 3 / 49 Report No.: T200205D04-SF Rev.: 00 Table of Contents 1 CERTIFICATE OF COMPLIANCE (SAR EVALUATION) .................................................... 5 2 DESCRIPTION OF EQUIPMENT UNDER TEST ............................................................... 6 2.1 SUMMARY OF HIGHEST SAR VALUES .............................................................................................................. 7 3 REQUIREMENTS FOR COMPLIANCE TESTING DEFINED ............................................... 8 3.1 REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC .......................................................... 8 4 DOSIMETRIC ASSESSMENT SYSTEM .......................................................................... 9 4.1 MEASUREMENT SYSTEM DIAGRAM .............................................................................................................. 10 4.2 SYSTEM COMPONENTS ................................................................................................................................... 11 5 EVALUATION PROCEDURES .................................................................................... 15 6 SAR MEASUREMENT PROCEDURES ......................................................................... 17 6.1 NORMAL SAR TEST PROCEDURE .................................................................................................................... 17 7 MEASUREMENT UNCERTAINTY .............................................................................. 19 8 ANTENNA LOCATION ............................................................................................. 20 9 SUMMARY OF SAR TEST EXCLUSION CONFIGURATIONS ........................................... 21 9.1 STANDALONE SAR TEST EXCLUSION CALCULATIONS ................................................................................. 21 9.1.1 SAR EXCLUSION CALCULATIONS FOR WI-FI ANTENNA < 50MM FROM THE USER ................................ 21 9.1.2 SAR EXCLUSION CALCULATIONS FOR WI-FI ANTENNA > 50MM FROM THE USER ................................ 22 9.1.3 SAR REQUIRED TEST CONFIGURATION ......................................................................................................... 23 10 EXPOSURE LIMIT ................................................................................................... 24 11 TISSUE DIELECTRIC PROPERTIES ............................................................................. 25 11.1 TEST LIQUID CONFIRMATION ......................................................................................................................... 25 11.2 TYPICAL COMPOSITION OF INGREDIENTS FOR LIQUID TISSUE PHANTOMS ........................................... 26 11.3 SIMULATING LIQUIDS PARAMETER CHECK RESULTS .................................................................................. 28 12 SYSTEM PERFORMANCE CHECK .............................................................................. 29 12.1 SYSTEM PERFORMANCE CHECK RESULTS .................................................................................................... 30 13 RF OUTPUT POWER MEASUREMENT ...................................................................... 31 13.1 WI-FI (2.4GHZ BAND) ....................................................................................................................................... 32 13.2 WI-FI (5GHZ BAND) ...............................…

Text truncated - open the document above for the full version.

Date: 2020/3/13 Dipole 2450 MHz_SN:727 Communication System: CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 1.83 S/m; ε r = 38.095; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient temperature: 22.1°C; Liquid temperature: 21.8°C DASY5 Configuration: • Probe: EX3DV4 - SN7466; ConvF(7.85, 7.85, 7.85) @ 2450 MHz; Calibrated: 2020/2/4 • Sensor-Surface: 2mm (Mechanical Surface Detection) • Electronics: DAE4 Sn856; Calibrated: 2019/4/24 • Phantom: ELI • DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373) Pin=250mW/Area Scan (51x61x1): Interpolated grid: dx=12 mm, dy=12 mm Maximum value of SAR (interpolated) = 22.1 W/kg Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 106.4 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 27.6 W/kg SAR(1 g) = 13.4 W/kg; SAR(10 g) = 6.24 W/kg Smallest distance from peaks to all points 3 dB below = 9.5 mm Ratio of SAR at M2 to SAR at M1 = 49.2% Maximum value of SAR (measured) = 20.4 W/kg 0 dB = 20.4 W/kg = 13.10 dBW/kg Date: 2020/3/16 Dipole 5300 MHz_SN:1023 Communication System: CW; Frequency: 5300 MHz; Duty Cycle: 1:1 Medium parameters used: f = 5300 MHz; σ = 4.578 S/m; ε r = 37.034; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient temperature: 22.4°C; Liquid temperature: 22.0°C DASY5 Configuration: • Probe: EX3DV4 - SN7466; ConvF(5.45, 5.45, 5.45) @ 5300 MHz; Calibrated: 2020/2/4 • Sensor-Surface: 2mm (Mechanical Surface Detection) • Electronics: DAE4 Sn856; Calibrated: 2019/4/24 • Phantom: ELI • DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373) Pin=100mW/Area Scan (51x51x1): Interpolated grid: dx=10 mm, dy=10 mm Maximum value of SAR (interpolated) = 16.9 W/kg Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 61.12 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 35.3 W/kg SAR(1 g) = 7.64 W/kg; SAR(10 g) = 2.18 W/kg Smallest distance from peaks to all points 3 dB below = 7.5 mm Ratio of SAR at M2 to SAR at M1 = 50% Maximum value of SAR (measured) = 16.3 W/kg 0 dB = 16.3 W/kg = 12.12 dBW/kg Date: 2020/3/17 Dipole 5600 MHz_SN:1023 Communication System: CW; Frequency: 5600 MHz; Duty Cycle: 1:1 Medium parameters used: f = 5600 MHz; σ = 4.95 S/m; ε r = 35.867; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient temperature: 22.6°C; Liquid temperature: 22.3°C DASY5 Configuration: • Probe: EX3DV4 - SN7466; ConvF(4.98, 4.98, 4.98) @ 5600 MHz; Calibrated: 2020/2/4 • Sensor-Surface: 2mm (Mechanical Surface Detection) • Electronics: DAE4 Sn856; Calibrated: 2019/4/24 • Phantom: ELI • DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373) Pin=100mW/Area Scan (51x51x1): Interpolated grid: dx=10 mm, dy=10 mm Maximum value of SAR (interpolated) = 17.4 W/kg Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 59.67 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 40.0 W/kg SAR(1 g) = 7.94 W/kg; SAR(10 g) = 2.24 W/kg Smallest distance from peaks to all points 3 dB below = 7.4 mm Ratio of SAR at M2 to SAR at M1 = 47.3% Maximum value of SAR (measured) = 17.1 W/kg 0 dB = 17.1 W/kg = 12.33 dBW/kg Date: 2020/3/18 Dipole 5800 MHz_SN:1023 Communication System: CW; Frequency: 5800 MHz; Duty Cycle: 1:1 Medium parameters used: f = 5800 MHz; σ = 5.16 S/m; ε r = 35.107; ρ = 1000 kg/m 3 Phantom section: Flat Section Ambient temperature: 21.5°C; Liquid temperature: 21.0°C DASY5 Configuration: • Probe: EX3DV4 - SN7466; ConvF(5.04, 5.04, 5.04) @ 5800 MHz; Calibrated: 2020/2/4 • Sensor-Surface: 2mm (Mechanical Surface Detection) • Electronics: DAE4 Sn856; Calibrated: 2019/4/24 • Phantom: ELI • DASY52 52.8.8(1258); SEMCAD X 14.6.10(7373) Pin=100mW/Area Scan (51x51x1): Interpolated grid: dx=10 mm, dy=10 mm Maximum value of SAR (interpolated) = 16.2 W/kg Pin=100mW/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 56.26 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 38.6 W/kg SAR(1 g) = 7.75 W/kg; SAR(10 g) = 2.18 W/kg Smallest distance from peaks to all points 3 dB below = 7.5 mm Ratio of SAR at M2 to SAR at M1 = 45.6% Maximum value of SAR (measured) = 15.8 W/kg 0 dB = 15.8 W/kg = 11.99 dBW/kg

FCC ID: X4D-SC-1 Page: 1 / 119 Report No.: T200205D04-RP1 Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C Test Standard FCC Part 15.247 Product name SYSTEM TABLET CONTROLLER Brand Name OLYMPUS Model No. SC-1 Test Result Pass Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. The test Result was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were given in ANSI C63.10: 2013 and compliance standards. The test results of this report relate only to the tested sample (EUT) identified in this report. The test Report of full or partial shall not copy. Without written approval of Compliance Certification Services Inc. (Wugu Laboratory). Approved by: Tested by: Kevin Tsai Dally Hong Deputy Manager Engineer Page: 2 / 119 Report No.: T200205D04-RP1 Rev.: 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 July 14, 2020 Initial Issue ALL Allison Chen 01 July 27, 2020 See the following note Rev.(01) P.A-1 Allison Chen Rev.(01) 1. Modify test setup photo for above 1GHz. Page: 3 / 119 Report No.: T200205D04-RP1 Rev.: 01 Table of contents 1. GENERAL INFORMATION ............................................................................................... 4 1.1 EUT INFORMATION ......................................................................................................... 4 1.2 EUT CHANNEL INFORMATION ....................................................................................... 5 1.3 ANTENNA INFORMATION ............................................................................................... 5 1.4 MEASUREMENT UNCERTAINTY .................................................................................... 6 1.5 FACILITIES AND TEST LOCATION................................................................................. 7 1.6 INSTRUMENT CALIBRATION ......................................................................................... 7 1.7 SUPPORT AND EUT ACCESSORIES EQUIPMENT ....................................................... 8 1.8 TEST METHODOLOGY AND APPLIED STANDARDS .................................................... 8 2. TEST SUMMERY .............................................................................................................. 9 3. DESCRIPTION OF TEST MODES .................................................................................. 10 3.1 THE WORST MODE OF OPERATING CONDITION ...................................................... 10 3.2 THE WORST MODE OF MEASUREMENT..................................................................... 11 3.3 EUT DUTY CYCLE ......................................................................................................... 12 4. TEST RESULT ................................................................................................................ 14 4.1 AC POWER LINE CONDUCTED EMISSION .................................................................. 14 4.2 6DB BANDWIDTH AND OCCUPIED BANDWIDTH (99%) ............................................. 17 4.3 OUTPUT POWER MEASUREMENT .............................................................................. 35 4.4 POWER SPECTRAL DENSITY ...................................................................................... 39 4.5 CONDUCTED BANDEDGE AND SPURIOUS EMISSION .............................................. 49 4.6 RADIATION BANDEDGE AND SPURIOUS EMISSION ................................................. 74 APPENDIX 1 - PHOTOGRAPHS OF EUT .............................................................................. A-1 Page: 4 / 119 Report No.: T200205D04-RP1 Rev.: 01 1. GENERAL INFORMATION 1.1 EUT INFORMATION Applicant ADLINK TECHNOLOGY INC. 9F, No.166, Jian Yi Rd., Zhonghe Dist., New Taipei City, 235 Taiwan Manufacturer ADLINK TECHNOLOGY INC. 9F, No.166, Jian Yi Rd., Zhonghe Dist., New Taipei City, 235 Taiwan Equipment SYSTEM TABLET CONTROLLER Model Name SC-1 Model Discrepancy N/A Trade Name OLYMPUS Received Date February 5, 2020 Date of Test February 17 ~ March 26, 2020 Power Supply 1. EUT Power from Adapter. FSP GROUP INC. / FSP065M-DBA I/P: 100-240Vac, 2.0-1.0A, 50-60Hz O/P: 19.0Vdc, 3.43A Max 2. Power from Rechargeable Litthium Polymer Battery. Rating: 11.1Vdc, 2300mAh HW Version A2 SW Version 7.2 Page: …

Text truncated - open the document above for the full version.

Page: 49 / 119 Report No.: T200205D04-RP1 Rev.: 01 4.5 CONDUCTED BANDEDGE AND SPURIOUS EMISSION 4.5.1Test Limit According to §15.247(d), In any 100 kHz bandwidth outside the authorized frequency band, Non-restricted bands shall be attenuated at least 20 dB/30 dB relative to the maximum PSD level in 100 kHz by RF conducted or a radiated measurement which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a). 4.5.2 Test Procedure Test method Refer as KDB 662911 D01, KDB 558074 D01. 1. EUT RF output port connected to the SA by RF cable, and the path loss was compensated to result. 2. SA setting, RBW=100kHz, VBW=300kHz, Detector=Peak, Trace mode = max hold, SWT = Auto. 3. In any 100 kHz bandwidth outside the authorized frequency band, shall be attenuated at least 20 dB relative to the maximum in-band peak PSD level in 100 kHz when conducted power procedure is used. f the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. 4.5.3 Test Setup Page: 50 / 119 Report No.: T200205D04-RP1 Rev.: 01 4.5.4 Test Result Test Data IEEE 802.11b mode Low CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 51 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11b mode Mid CH chain 0 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 52 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11b mode High CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 53 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11g mode Low CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 54 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11g mode Mid CH chain 0 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 55 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11g mode High CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 56 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT20 mode Low CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 57 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT20 mode Mid CH chain 0 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 58 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11n HT20 mode High CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 59 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT40 mode Low CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 60 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT40 mode Mid CH chain 0 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 61 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11n HT40 mode High CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 62 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11b mode Low CH chain 1 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 63 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11b mode Mid CH chain 1 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 64 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11b mode High CH chain 1 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 65 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11g mode Low CH chain 1 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 66 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11g mode Mid CH chain 0 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 67 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11g mode High CH chain 1 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 68 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT20 mode Low CH chain 1 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 69 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT20 mode Mid CH chain 1 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 70 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11n HT20 mode High CH chain 1 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 71 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT40 mode Low CH chain 1 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 72 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11 n HT40 mode Mid CH chain 1 Reference Level of PSD in 100kHz Spurious Emission 30MHz-25GHz Page: 73 / 119 Report No.: T200205D04-RP1 Rev.: 01 IEEE 802.11n HT40 mode High CH chain 0 Reference Level of PSD in 100kHz Band Edge Spurious Emission 30MHz-25GHz Page: 74 / 119 Report No.: T200205D04-RP1 Rev.: 01 4.6 RADIATION BANDEDGE AND SPURIOUS EMISSION 4.6.1 Test Limit FCC according to §15.247(d), §15.209 and §15.205, In any 100 kHz bandwidth outside the authorized frequency band, all harmonic and spurious must be least 20 dB below the highest emission level with the authorized frequency band. Radiation emission which fall in the restricted bands must also follow the FCC section 15.209 as below limit in table. Below 30 MHz Frequency Field Strength (microvolts/m) Magnetic H-Field (microamperes/m) Measurement Distance (metres) 9-490 kHz 2,400/F (F in kHz) 2,400/F (F in kHz) 300 490-1,705 kHz 24,000/F (F in kHz) 24,000/F (F in kHz) 30 1.705-30 MHz 30 N/A 30 Above 30 MHz Frequency Field Strength (microvolts/m) Measurement Distance (metres) 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 Page: 75 / 119 Report No.: T200205D04-RP1 Rev.: 01 4.6.2 Test Procedure Test method Refer as KDB 662911 D01, KDB 558074 D01. 1. The EUT is placed on a turntable, Above 1 GHz is 1.5m and below 1 GHz …

Text truncated - open the document above for the full version.

FCC ID: X4D-SC-1 Page: 1 / 42 Report No.: T200205D04-RP3 Rev.: 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw www.ccsrf.com Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group RADIO TEST REPORT FCC 47 CFR PART 15 SUBPART C Test Standard FCC Part 15.247 Product name SYSTEM TABLET CONTROLLER Brand Name OLYMPUS Model No. SC-1 Test Result Pass Statements of Conformity Determination of compliance is based on the results …

Text truncated - open the document above for the full version.