X9P20100726BLUETOOTH KEYBOARD SILICONE

MCU Crystal Frequency: 24MHz RF Crystal Frequency: 24MHz ANTENNA EEPROM MCU&RF (BCM2042) POWER

Shenzhen Paoluy Silicone Technology Co., Ltd. Letter of Authorization FCC ID: X9P20100726 Jul. 20, 2010 Federal Communications Commission Authorization and Evaluation Divisoin 7435 Oakland Mills Road Columbia, MD 21046 To Whom It’s My Concern: We, the undersigned,hereby Authorize Anbotek Compliance Laboratory Limited (Daniel Zhu) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Anbotek Compliance Laboratory Limited (Daniel Zhu). On our behalf shall have the same effect as acts of our own. This Authorization expires on Aug. 20, 2010 This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Shenzhen Paoluy Silicone Technology Co., Ltd., are not subject to a denial of federal benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988.21 USC835a, and no party to the application is subject to a denial of federal benefits pursuant to that section.

Page 20 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F Figure 1 The EUT-Overall View Figure 2 The EUT-Inside View Page 21 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F Figure 3 The EUT-Front View Figure 4 The EUT-Back View

FCC ID Label Sample for FCC ID: X9P20100726 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

The proposed Label Location on EUT Proposed FCC ID Label Location Proposed Label Location on EUT The EUT-Back View/Proposed FCC ID Label Location

Page 22 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F Figure 5 PCB of the EUT-Front View Figure 6 PCB of the EUT-Back View Page 23 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F Figure 7 PCB of the EUT-Front View Figure 8 PCB of the EUT-Front View(RF Module) Page 24 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F Figure 9 PCB of the EUT-Back View(RF Module)

APPLICANT: Shenzhen Paoluy Silicone Technology Co., Ltd. FCC ID: X9P20100726 The theory of Bluetooth Keyboard Silicone BL-BKB76A: 1. MCU & RF module: responsible for communication with receiver to PC. 2. MCU crystal frequency is 24MHz. 3. RF module crystal frequency is 24MHz. 4. Power circuit: to provide steady power to around circuit. 5. LED display: display current state of BL-BKB76A. 6. The antenna of equipment is on the PCB. 7. The antenna gain is 0dBi.

UnRegistered

Page 1 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F FCC TEST REPORT for Shenzhen Paoluy Silicone Technology Co., Ltd. Bluetooth Keyboard Silicone Model No.: BL-BKB76A, BL-BKB76B, BL-BKB76C, BL-BKB-121A, BL-BKB-121B, BL-BKB-121C Report Number : 201007725F Date of Test : Jul. 26~Aug. 09, 2010 Date of Report : Aug. 12, 2010 Prepared for : Shenzhen Paoluy Silicone Technology Co., Ltd. Address : No.31, furong road, gushu village, xixiang town, bao’an district, shenzhen Tel: (86) 755-33819221 Fax: (86) 755-33676866 Prepared By : Anbotek Compliance Laboratory Limited Address : 2/F, Langfeng Building, Kefa Road North, Hi-tech Industrial Park, Nanshan District, Shenzhen 518057, China Tel: (86) 755-26014771 Fax: (86) 755-26014772 Page 2 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F TABLE OF CONTENT Description Page Test Report 1. GENERAL INFORMATION .........................................................................................................4 1.1. Description of Device (EUT)....................................................................................................................4 1.2. Description of Test Facility ......................................................................................................................5 1.3. Measurement Uncertainty.........................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT.................................................................... 6 3. TEST PROCEDURE ....................................................................................................................... 7 4. CONDUCTED LIMITS .................................................................................................................. 8 4.1. Block Diagram of Test Setup ...................................................................................................................8 4.2. Power Line Conducted Emission Measurement Limits (15.207) .............................................................8 4.3. Configuration of EUT on Measurement ...................................................................................................8 4.4. Operating Condition of EUT ....................................................................................................................8 4.5. Test Procedure ..........................................................................................................................................9 4.6. Power Line Conducted Emission Measurement Results ..........................................................................9 5. RADIATION INTERFERENCE.................................................................................................. 12 5.1. Requirements (15.249, 15.209): .............................................................................................................12 5.2 Test Procedure .........................................................................................................................................12 5.3 Test Results..............................................................................................................................................12 6. OCCUPIED BANDWIDTH..........................................................................................................16 6.1. Requirements (15.249): ..........................................................................................................................16 6.2 Test Results..............................................................................................................................................16 7. PHOTOGRAPH............................................................................................................................. 18 7.1. Photo of Power Line Conducted Emission Measurement ......................................................................18 7.2. Photo of Radiation Emission Test ..........................................................................................................18 APPENDIX I (Photos of EUT) (5 Pages) Page 3 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F TEST REPORT Applicant : Shenzhen Paoluy Silicone Technology Co., Ltd. Manufacturer : Shenzhen Paoluy Silicone Technology Co., Ltd. EUT : Bluetooth Keyboard Silicone Model No. : BL-BKB76A, BL-BKB76B, BL-BKB76C, BL-BKB-121A, BL-BKB-121B, BL-BKB-121C Serial No. : N/A Rating : DC 3.7-4.2V via Lithium Battery Trade Mark : N/A Measurement Procedure Used: FCC Part15 Subpart C, Paragraph 15.207, 15.249 & 15.209 The device described above is tested by Anbotek Compliance Laboratory Limited to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and Anbotek Compliance Laboratory Limited is assumed full of responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC Part 15 Subpart C requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of Anbotek Compliance Laboratory Limited Date of Test : Jul. 26~Aug. 09, 2010 Prepared by : (Engineer) Reviewer : (Project Manager) Approved & Authorized Signer : (Manager) Page 4 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F 1. GENERAL INFORMATION 1.1. Description of Device (EUT) EUT : Bluetooth Keyboard Silicone Model Number : BL-BKB76A, BL-BKB76B, BL-BKB76C, BL-BKB-121A, BL-BKB-121B, BL-BKB-121C (Note: The above samples are same except the model number & Shape of appliances, so we prepare “BL-BKB76A” for Radio test only.) Test Power Supply : AC 120V, 60Hz for PC; DC 3…

Text truncated - open the document above for the full version.

Page 18 of 24 FCC ID: X9P20100726 Anbotek Compliance Laboratory Limited Report No.201007725F 7. PHOTOGRAPH 7.1. Photo of Power Line Conducted Emission Measurement 7.2. Photo of Radiation Emission Test