XBTZBM-220ZigBee Module

UIS 1 | P a g e User Manual ZBM-220 UIS 2 | P a g e Contents Certification Notices 1. Overview 2. Specification 3. Pin Assignment UIS 3 | P a g e Certification Notices FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Labeling requirements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. UIS 4 | P a g e Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. This device is intended for OEM integrators only. Please see the full Grant of Equipment document for other restrictions. This device must be operated and used with a locally approved access point. Information To Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with "Contains FCC ID:XBTZBM-220, FCC ID displayed on the label. The label text should be updated according to the table shown in Ordering Guide section of this document. UIS 5 | P a g e 1. Overview ZMB-220 is a wireless communication modem based on IEEE802.15.4, which can be widely used in home automation and security, automatic meter reading, factory automation, toys and so on. 2. SPECIFICATION General Specification Specification Transmit Frequency2405MHz to 2480MHz ModulationOQPSK Programmable Output PowerUp to 4.5 dBm Operation Voltage2.0V~3.6V Environmental Operating Temperature -10°C to 70°C Storage Temperature -40°C to 85°C Humidity90% RH Max., Non-Condensing Mechanical Specification Dimension (WxHxD, mm)26.2 x 2.0 x 16.5 2.4-GHz IEEE 802.15.4 Compliant RF Transceiver UIS 6 | P a g e 3. Pin Assignment UIS 7 | P a g e Pin NameDescriptionDirection 1GNDPower Ground I 2AVDDDC input(+2.0 ~3.6V) I 3Port 2.4/32.768 kHz XOSCI/O 4Port 2.3/32.768 kHz XOSCI/O 5P2_2Port 2.2I/O 6P2_1Port 2.1I/O 7P2_0Port 2.0I/O 8P1_7Port 1.7I/O 9P1_6Port 1.6I/O 10VDDDC input(+2.0 ~3.6V) I 11GNDPower Ground I 12P1_5Port 1.5I/O 13P1_4Port 1.4I/O 14P1_3Port 1.3I/O 15P1_2Port 1.2I/O 16P1_1I/O 17VDDDC input(+2.0 ~3.6V) I 18P1_0I/O 19P0_7Port 0.7I/O 20P0_6Port 0.6I/O 21P0_5Port 0.5I/O 22P0_4Port 0.4I/O 23P0_3Port 0.3I/O 24P0_2Port 0.2I/O 25P0_1Port 0.1I/O 26P0_0Port 0.0I/O 27RESET_NReset, active-lowI 28GNDPower Ground I 29GNDPower Ground I P2_4/XOSC3 2K_Q1 P2_3/XOSC3 2K_Q2 Port 1.1 – 20-mA drive capability Port 1.0 – 20-mA drive capability

Applicant/Grantee United Integrated Services CO., LTD./ XBT FCC ID: XBTZBM-220 Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Device is equipped with Metal shielding to cover RF section. Refer to external photos. Y 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. All inputs to the modules are buffered through logic or microprocessor inputs. Y 3 The modular transmitter must have its own power supply regulation. The transmitter has its own power supply regulator. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Device is using for Printed Antenna, so there are no any connector in the device. Refer to external photos. Y 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting EUT was tested in a stand alone configuration via an extender card. Please see section photographs of test configuration in the test report, the EUT was plugged in this extender card. Y equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. One label is to be placed on the module. Refer to FCC ID label format and location file. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Refer to “User’s Guide” Exhibit. Y

ETC Report No. : 13-01-RBF-035 FCC ID: XBTZBM-220 Sheet 1 of 2 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 1. 2.

ETC Report No. : 13-01-RBF-035 FCC ID: XBTZBM-220 Sheet 2 of 2 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 3. 4.

FCC ID: XBTZBM-220 RF Exposure Evaluation of E.U.T. : ZIGBEE MODULE FCC ID. : XBTZBM-220 MODEL : ZBM-220 for APPLICANT : United Integrated Services CO., LTD. ADDRESS : 5 F No 3 Lane 7 Paokao Road Hsintien 23144 Taipei Hsien ,Taiwan Prepared by ELECTRONICS TESTING CENTER, TAIWAN NO. 34. LIN 5. DINGFU, LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail: [email protected] Report Number : 13-01-RBF-035-MPE FCC ID: XBTZBM-220 Product Information: Type of EUT: ZIGBEE MODULE FCC ID: XBTZBM-220 Manufacturer: United Integrated Services CO., LTD. Model: ZBM-220 Description: Frequency band: 2405MHz~2480MHz Number of channels: 16 channels Channel spacing: 5MHz Transmitter antenna source: Printed Antenna Maximum conducted output power (measured): 3.44 dBm or 2.208mW The following table lists the provided authorized antennas: Antenna Gain Model Antenna Type (dBi) Numeric N/A Printed Antenna2.0 1.58 Below is an example of the RF Exposure Statement: IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. FCC ID: XBTZBM-220 Relative Requirement for Compliance According to section 1.1310 of FCC 47 CFR Part 1, limits for maximum permissible exposure (MPE) are as following: TABLE 1 – LIMITS FOR MAXIMUN PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.0 .................. 6141.63*(100) 6 3-30 ..................... 1842/f4.89/f *(900/f 2 ) 6 30-300 .................. 61.40.1631.0 6 300-1500 ............... ...................... ......................f/300 6 1500-100,000 ......... ...................... ......................5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 ............... 6141.63*(100) 30 1.34-30 ............... 824/f2.19/f*(180/f2) 30 30-300 .................. 27.50.0730.2 30 300-1500 ............... ...................... ......................f/1500 30 1500-100,000 ......... ...................... ......................1.0 30 f = frequency in MHz * = Plane-wave equivalent power density NOTE 1 TO TABLE 1: Occupational/controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when an individual is transient through a location where occupational / controlled limits apply provided he or she is made aware of the potential for exposure. NOTE 2 TO TABLE 1: General population/uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not be fully aware of the potential for exposure or can not exercise control over their exposure. FCC ID: XBTZBM-220 RF Exposure Calculations: The following information provides the minimum separation distance for the highest gain antenna provided. This calculation is based on the highest EIRP possible from the system, considering maximum power and antenna gain, and considering a 1.0 mW/cm 2 uncontrolled exposure limit. The formula shown in OET Bulletin 65 is used in the calculation. Equation from page 19 of OET Bulletin 65, Edition 97-01 is: S= PG / 4πR 2 where: S = power density (in appropriate units, e.g. mW/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) hence R= (PG / 4πS) 1/2 For our device P = 2.208mW G = 1.58 R = 20 cm S = (2.208 * 1.58) / (4*π*20 2 ) = 0.0007 mW/cm 2 < 1.0 mW/cm 2 For complying the FCC limits for general population/uncontrolled exposure, the power density limit is 1.0 mW/cm 2 . The calculation result of the power density at a distance of 20 cm of our device is less than the limit. This means that according to OET Bulletin 65 (Edition 97-01), Supplement C (Edition 01-01), the equipment fulfills the requirements on power density for general population/uncontrolled exposure and therefore fulfills the requirements of 47 CFR Part 15.247 (i).

Rev. No 2.0 FCC Part 15 EMI TEST REPORT of E.U.T. : ZIGBEE MODULE Model No. : ZBM-220 FCC ID. : XBTZBM-220 for APPLICANT : United Integrated Services CO., LTD. ADDRESS : 5F No 3 Lane 7 Paokao Road Hsintien 23144 Taipei Hsien ,Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34. LIN 5, DINGFU VIL., LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C Tel : (02)26023052 Fax : (02)26010910 http://www.etc.org.tw ; e-mail: [email protected] Report Number : 13-01-RBF-035 ETC Report No. : 13-01-RBF-035 FCC ID: XBTZBM-220 Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : United Integrated Services CO., LTD. 5F No 3 Lane 7 Paokao Road Hsintien 23144 Taipei Hsien ,Taiwan Manufacturer : United Integrated Services CO., LTD. 5F No 3 Lane 7 Paokao Road Hsintien 23144 Taipei Hsien ,Taiwan Description of EUT a) Type of EUT ZIGBEE MODULE b) Trade Name UIS c) Model No. ZBM-220 d) Power Supply : : : : DC 3V Regulation Applied : FCC Rules and Regulations Part 15 Subpart C I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Summary of Tests Test Results Radiated Emission Pass Conducted Emission Pass Emission Bandwidth Pass Output Power Pass 100 kHz Bandwidth of Band Edges Pass Power Density Pass Out-of-Band Conducted Emission Pass ETC Report No. : 13-01-RBF-035 FCC ID: XBTZBM-220 Rev. No 1.0 Date Test Item Received : Jan. 26, 2013 Date Test Campaign Completed : Feb. 06, 2013 Date of Issue : May 17, 2013 Test Engineer : ( Vincent Chang, Engineer ) Approve & Authorized : S. S. Liou, Section Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : 13-01-RBF-035 FCC ID: XBTZBM-220 Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ....................................................................................................... 1 1.1 Product Description...................................................................................................................... 1 1.2 Characteristics of Device ............................................................................................................. 1 1.3 Test Methodology ........................................................................................................................ 1 1.4 Test Facility.................................................................................................................................. 1 2 PROVISIONS APPLICABLE...................................................................................................... 2 2.1 Definition ..................................................................................................................................... 2 2.2 Requirement for Compliance ....................................................................................................... 3 2.3 Restricted Bands of Operation ..................................................................................................... 5 2.4 Labeling Requirement .................................................................................................................. 5 2.5 User Information .......................................................................................................................... 6 3. SYSTEM TEST CONFIGURATION .......................................................................................... 7 3.1 Justification .................................................................................................................................. 7 3.2 Devices for Tested System........................................................................................................... 7 4 RADIATED EMISSION MEASUREMENT .............................................................................. 8 4.1 Applicable Standard ..................................................................................................................... 8 4.2 Measurement Procedure............................................................................................................... 8 4.3 Measuring Instrument ................................................................................................................ 10 4.4 Radiated Emission Data ............................................................................................................. 11 4.5 Field Strength Calculation ......................................................................................................... 23 4.6 Photos of Radiation Measuring Setup........................................................................................ 24 5 CONDUCTED EMISSION MEASUREMENT ........................................................................ 25 5.1 Standard Applicable ................................................................................................................... 25 5.2 Measurement Procedure............................................................................................................. 25 5.3 Conducted Emission Data .......................................................................................................... 27 5.4 Result Data Calculation ............................................................................................................. 29 5.5 Conducted Measurement Equipment ......................................................................................... 29 5.6 Photos of Conduction Measuring Setup..................................................................................... 30 6 ANTENNA REQUIREMENT ...............................................................................................…

Text truncated - open the document above for the full version.

ETC Report No. : 13-01-RBF-035 FCC ID: XBTZBM-220 Sheet 18 of 44 Sheets Rev. No 2.0 4.6 Photos of Radiation Measuring Setup