XZB-MAXR7202802.11a/b/g/n WLAN mini-PCI card

Arada Systems, Inc. 4633 Old Ironsides Drive, Suite 415, Santa Clara, CA95054, USA MaxR-7202 Mini PCI User’s Manual 1. Product Overview The MaxR-7202 series PCI adapter cards contain an Atheros AR9220 chip for IEEE 802.11a/b/g/n Wireless LAN applications. The mini PCI adapter cards support key security features like Wi-Fi Protected Access (WPA), WPA2, WEP and 802.1x. 2. Packaging Contents The mini PCI card package contains the following item(s): 1 x Wireless Mini PCI Adapter 3. Installation guide
Shut down the power of the platform
Align the PCI adapter with the Mini PCI socket on the platform
Adjust and push down the PCI adapter gently until the metal locking levers on the Mini PCI socket is latched. (Please take note that the PCI adapter can only fit in one direction due to the keyed notch. Wrong orientation will cause improper installation and may damage the Mini PCI socket)
Connect the antenna(s) on the mini PCI module
Reboot on the platform
Install drivers if necessary 4. Frequency 802.11b/g/n: 2412 ~ 2472 MHz 802.11an: 5180 ~ 5240MHz, 5725 ~ 5850MHz 5. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Arada Systems, Inc. 4633 Old Ironsides Drive, Suite 415, Santa Clara, CA95054, USA
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. 6. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only. 7. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 8. Important Notes This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for a population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Arada Systems, Inc. 4633 Old Ironsides Drive, Suite 415, Santa Clara, CA95054, USA 9. Label for end product must include “Contains FCC ID: XZB-MAXR7202” or “A RF transmitter inside, FCC ID: XZB-MAXR7202”

AradaSystems,Inc 4633OldIronsldesDriveSuite415SantaClaraCalifornia95054UnitedStates Tel:4087739298 Fax:4087163238 ConfidentialLetter Date:2011/7111 FederalCommunicationsCommission AuthorizationandEvaluationDivision FCCID: XZB-MAXR7202 ConfidentialityRequest PursuanttoSections0.457and0.459oftheCommission'sRules,theApplicantHerebyrequestsconfidential treatmentofInformationaccompartingthisApplicationAsoutlinedbelow: 1.BlockDiagram 2.CircuitDiagram 3.OperationalDescription Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleasedtothepublic. ThepublicdisclosureofthesemattersmightbeharmfultotheApplicantandprovideunjustifiedbenefitstoits competitors. TheApplicantunderstandsthatpursuanttoRule0.457,disclosureofthisApplicationandallaccompanying documentationwillnotbemadebeforethedateoftheGrantforthisapplication Sincerely, Applicant'scompanynameAradaSystems,Inc 4633 OldIronsldesDriveSuite415SantaClaraCalifornia 95054UnitedStates Applicant'scompanyaddress Signature r JobTItleandDept. E-Mail PraveenSingh/ CEO [email protected] Tel.4087739298

AradaSystems,Inc 4633OldIronsldesDriveSuite415SantaClaraCalifornia95054UnitedStates Tel:4087739298 Fax:4087163238 DoCAttestationLetter Date:2011/7111 WeAradaSystems,Inc,asthegranteeofthisprojectFCCID:XZB-MAXR7202,wouldliketodeclarethatthe compositeportioncategorizedascomputerperipheralhasbeenauthorizedundertheDeclarationof Conformityprocedures. Regards, FCCGranteecontactpersoninformation. Applicant'scompanyname: AradaSystems,Inc 4633OldIronsidesDriveSuite415SantaClaraCalifornia Applicant'scompanyaddress 95054UnitedStates Signature JobTitleandDept. E-Mail PraveenSingh/ CEO [email protected] Tel. 4087739298

Page No. : 19 Limited Module Approval Request Letter Subject: Limited Module Approval Date: 2011/7/11 FCC ID: XZB-MAXR7202 Dear Reviewer, We, Sporton International Inc., are authorized by Arada Systems, Inc to have their state-of-the-art 802.11a/b/g/n WLAN mini-PCI card approved under limited module approval authorization. The application of this module is specified to mobile host equipment. The requirements regulated in Public Notice DA00-1407 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip AR922x. 3. The requirement of power supply regulation: The part number of the power regulator is AME88052EFTZ 2.0V. 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Company name : Sporton International Inc. Company Address : No.8, Lane 724, Bo-ai St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Signature : Name : Leo Huang Job Title : Manager

AradaSystems,Inc 4633OldIronsldesDriveSuite415SantaClaraCalifornia95054UnitedStates Tel:4087739298Fax:4087163238 PowerofAttorney Date:2011/7/11 DearSir, I herebyhaveentrustedthefollowingpersontobea proxyregardingapplicationforTypeCertification. SportonInternationalInc. Address: No.8,Lane724,Bo-aiSt.,JhubeiCity,HslnChuCounty302,Taiwan,R.O.C. Name: LeoHuang JobTitle: Manager e-mail:[email protected] I amthereforeresponsibleforthecontentsoftheapplication. Brandnameandmodeltypeofthespecifiedradioequipment:AradaIMaxR-7202 FCCID:XZB-MAXR7202 Productname:802.11O/b/g/nWLANmlnl-PCIcard FCCGranteecontactpersonInformation. Applicant'scompanyname: AradaSystems,Inc 4633 OldIronsldesDriveSuite415SantaClaraCalifornia Applicant'scompanyaddress 95054UnitedStates Signature JobTitleandDept. PraveenSingh/ CEO E-Mail [email protected] Tel. 4087739298

SPORTON International Inc. PAGE NUMBER : A1 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A4 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A5 OF A5 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255

MaxR-7202 Mini PCI Label 35.4 mm 14.7 mm

SPORTON International Inc. PAGE NUMBER : A1 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255 APPENDIX A. Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A4 OF A4 TEL : 886-2-2696-2468 ISSUED DATE : Jul. 08, 2011 FAX : 886-2-2696-2255

Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : C1 of C3 Appendix C. Maximum Permissible Exposure Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : C2 of C3 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.25 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) ＝ d GP30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Peak RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 377 30 d GP   From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : C3 of C3 1.3. Calculated Result and Limit For 5GHz UNII Band: Antenna Type : Dipole Antenna Max Conducted Power for IEEE 802.11n 20MHz MCS8 : 16.74dBm Antenna Gain (dBi) Antenna Gain (numeric) Average Output Power (dBm) Average Output Power (mW) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 3.80 2.3988 16.7445 47.2548 0.022563 1 Complies For 5GHz ISM Band: Antenna Type : Dipole Antenna Max Conducted Power for IEEE 802.11n 20MHz MCS8: 22.06dBm Antenna Gain (dBi) Antenna Gain (numeric) Average Output Power (dBm) Average Output Power (mW) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 3.80 2.3988 22.0597 160.6821 0.076722 1 Complies For 2.4GHz Band: Antenna Type : Dipole Antenna Max Conducted Power for IEEE 802.11b: 24.30 dBm Directional Antenna Gain (dBi) Antenna Gain (numeric) Average Output Power (dBm) Average Output Power (mW) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 4.81 3.0271 24.3010 269.2177 0.162212 1 Complies Note: Directional Antenna Gain = Test Antenna Gain + 10 log (Antenna quantity) CONCULSION: Both of the WLAN 2.4GHz Band and WLAN 5GHZ Band can transmit simultaneously, the formula of calculatedthe MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density Therefore, the worst-case situation is 0.076722 / 1 + 0.162212 / 1 = 0.238934, which isless than “1”. This confirmed that the device comply with FCC 1.1310 MPE limit.

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: 01 FCC RADIO TEST REPORT Applicant’s company Arada System, Inc Applicant Address 4633 Old Ironsides Drive, Suite 415 Santa Clara, CA 95054 FCC ID XZB-MAXR7202 Manufacturer’s company Arada System, Inc Manufacturer Address 4633 Old Ironsides Drive, Suite 415 Santa Clara, CA 95054 Product Name 802.11a/b/g/n WLAN mini-PCI card Brand Name Arada Model Name MaxR-7202 Test Rule Part(s) 47 CFR FCC Part 15 Subpart C § 15.247 Test Freq. Range 2400 ~ 2483.5MHz / 5725 ~ 5850MHz Received Date Feb. 17, 2011 Final Test Date Jun. 23, 2011 Submission Type Original Equipment Statement Test result included is only for the IEEE 802.11n, IEEE 802.11b/g part and IEEE 802.11a (5725 ~ 5850MHz) of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.10-2009 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report No.: FR121723-01AB Report Format Version: 01 Page No. : i of ii FCC ID: XZB-MAXR7202 Issued Date : Jul. 08, 2011 Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories .........................................................................................................................................................................................5 3.3. Table for Filed Antenna.......................................................................................................................................................................6 3.4. Table for Carrier Frequencies .............................................................................................................................................................7 3.5. Table for Test Modes ...........................................................................................................................................................................8 3.6. Table for Testing Locations..................................................................................................................................................................9 3.7. Table for Supporting Units ...................................................................................................................................................................9 3.8. Table for Parameters of Test Software Setting ...................................................................................................................................10 3.9. Test Configurations ...........................................................................................................................................................................12 4. TEST RESULT ................................................................................................................................................... 14 4.1. AC Power Line Conducted Emissions Measurement.........................................................................................................................14 4.2. Peak Output Power Measurement ....................................................................................................................................................18 4.3. Average Output Power Measurement ..............................................................................................................................................26 4.4. Power Spectral Density Measurement ..............................................................................................................................................29 4.5. 6dB Spectrum Bandwidth Measurement ..........................................................................................................................................38 4.6. Radiated Emissions Measurement ....................................................................................................................................................44 4.7. Band Edge Emissions Measurement .................................................................................................................................................70 4.8. Antenna Requirements .....................................................................................................................................................................82 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 83 6. TEST LOCATION.............................................................................................................................................. 85 7. TAF CERTIFICATE OF ACCREDITATION ............................................................................................................. 86 APPENDIX A. PHOTOGRAPHS OF EUT.......................................................................................................... A1 ~ A9 APPENDIX B. …

Text truncated - open the document above for the full version.

Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : 1 of 7 Appendix B. Test Photos Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : 2 of 7 1. Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : 3 of 7 SIDE VIEW SIDE VIEW Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : 4 of 7 2. Photographs of Radiated Emissions Test Configuration Test Configuration: 9kHz ~30MHz FRONT VIEW REAR VIEW Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : 5 of 7 Test Configuration: 30MHz~1GHz FRONT VIEW REAR VIEW Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : 6 of 7 SIDE VIEW Report No.: FR121723-01 FCC ID: XZB-MAXR7202 Page No. : 7 of 7 Test Configuration: Above 1GHz FRONT VIEW REAR VIEW