Y8AMIP669AWireless Speaker

iLive2 WARNING: Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode. WARNING: Shock hazard - Do Not Open. AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the Mains Plug or Direct plug-in adapter should be disconnected from the mains socket outlet completely. La fiche d’alimentation ou adaptateur de courant est utilisé comme dispositif de déconnexion et doit rester accessible pendant l’utilisation. Pour mettre l’appareil hors tension, la fiche ou adaptateur de courant doit être débranché de la prise de courant. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries. No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.). CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité. CAUTION: Use of any controls or adjustments or performance of procedures other than those herein specified may result in hazardous radiation exposure. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. PRÉCAUTION: Danger d’explosion si les piles sont remplacées de façon incorrect. Remplacer les piles seulement par le même type de pile ou l’équivalent. WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in the unit. Only use rechargeable NiMH batteries. WARNING: The battery, batteries, and battery pack shall not be exposed to excessive heat such as sunshine, fire, or the like. 7KHOLJKWQLQJÀDVKZLWKDUURZKHDGV\PEROZLWKLQ DQHTXLODWHUDOWULDQJOHLVLQWHQGHGWRDOHUWWKHXVHU WRWKHSUHVHQFHRIXQLQVXODWHGGDQJHURXVYROWDJH ZLWKLQWKHSURGXFW VHQFORVXUHWKDWPD\EHRI VXI¿FLHQWPDJQLWXGHWRFRQVWLWXWHDULVNRIHOHFWULF VKRFNWRSHUVRQV WARNING: TO REDUCE THE RISK OF (/(&75,&6+2&.'21275(029( &29(5 25%$&. 1286(5 6(59,&($%/(3$576,16,'(5()(5 6(59,&,1*7248$/,),('6(59,&( 3(56211(/ 0CC4=C8>= A8B@D43q;42CA>2DC8>= =4?0B>DEA8A 20DC8>= A8B:>54;42CA82B7>2: 3>=>C>?4= 7KHH[FODPDWLRQSRLQWZLWKLQDQHTXLODWHUDOWULDQJOH LVLQWHQGHGWRDOHUWWKHXVHUWRWKHSUHVHQFHRI LPSRUWDQWRSHUDWLQJDQGPDLQWHQDQFH VHUYLFLQJ  LQVWUXFWLRQVLQWKHOLWHUDWXUHDFFRPSDQ\LQJWKH DSSOLDQFH Warnings and Precautions Important Safety Instructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. FCC Warnings WARNING approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC RF radiation exposure …

Text truncated - open the document above for the full version.

Date:March 18, 2011 Federal Communications Commission Authorization and Evaluation Division FCC ID: Y8AMIP669A Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this application as outlined below: 1. Block diagram 2. Schematics 3. Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might to harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Sincerely, （Liming Jiang） （Certification Engineer） （NGAI LIK ELECTRONICS ENTERPRISES LIMITED） Tel: 86-769-87771430 EXT. 5275 Fax: 86-769-87771430 EXT. 5265 Web site: www.ngailik.com E-mail: [email protected]

AGENCY AUTHORIZATION LETTER FCC ID: Y8AMIP669A Date: March 18, 2011 To whom it may concern: We, the undersigned, hereby authorize NS Technology Co., Ltd. NS to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by NS within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months form original date. If you have any Questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, （Liming Jiang） （Certification Engineer） （NGAI LIK ELECTRONICS ENTERPRISES LIMITED） Tel: 86-769-87771430 EXT. 5275 Fax: 86-769-87771430 EXT. 5265 Web site: www.ngailik.com E-mail: [email protected]

Label location

Antenna location

FCC ID:Y8AMIP669A Report No.:FC110128N05 1 Report Format Version 0.0.1 FCC TEST REPORT REPORT NO.: FC110128N05 MODEL NO.: MIP669A,ITPW891B(See Item 3.1) RECEIVED: Jan.28, 2011 TESTED: Mar.10~Mar.15, 2011 ISSUED: Mar.18, 2011 APPLICANT: NGAI LIK ELECTRONICS ENTERPRISES LIMITED ADDRESS: FLAT 29-32,8/F., BLOCK B, FOCAL INDUSTRIAL CENTRE, 21 MAN LOK STREET, HUNG HOM, KOWLOON, HONG KONG ISSUED BY: NS Technology Co., Ltd. LAB ADDRESS: Chenwu Industrial Zone, Houjie Town, Dongguan, Guangdong, China This test report consists of 4 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by A2LA, or any government agency. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Test Lab Cert 2951.01 FCC ID:Y8AMIP669A Report No.:FC110128N05 2 Report Format Version 0.0.1 PRODUCT: IPhone/iPod bar speaker MODEL: MIP669A,ITPW891B (see Item 3.1) BRAND: iLIVE APPLICANT: NGAI LIK ELECTRONICS ENTERPRISES LIMITED TESTED: Mar.10~Mar.15, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 15, Subpart C (Section 15.247) ANSI C63.4-2003 47 CFR FCC Part 2 Subpart J, section 2.1091 The above equipment has been tested by NS Technology Co., Ltd., and found compliance with the requirements of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. REVIEWED BY : DATE: Mar.18, 2011 Henry Wang / Supervisor APPROVED BY : DATE: Mar.18, 2011 Chris Du / Manager FCC ID:Y8AMIP669A Report No.:FC110128N05 3 Report Format Version 0.0.1 Maximum Permissible Exposure 1 Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user and the device. (a) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density(S) (mW/cm 2 ) Averaging Times ︱E︱ 2 ,︱H︱ 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100000 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density(S) (mW/cm2) Averaging Times ︱E︱ 2 ,︱H︱ 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100000 1.0 30 Note: f=frequency in MHz; *Plane-wave equivalent power density 2 MPE Calculation Method E (V/m) = (30*P*G) 0.5 /d Power Density: Pd (W/m 2 ) = E 2 /377 E = Electric Field (V/m) P = Peak RF output Power (W) G = EUT Antenna numeric gain (numeric) d = Separation distance between radiator and human body (m) The formula can be changed to Pd = (30*P*G) / (377*d 2 ) From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. FCC ID:Y8AMIP669A Report No.:FC110128N05 4 Report Format Version 0.0.1 3 Calculated Result and Limit Mode CH Output power (dBm) Output power (mW) Antenna Gain (dBi) MPE estimation result (mW/cm²) at 20cm Limit of MPE Estimation (mW/cm²) Test result CH1:2406MHz 14.68 29.37 0.5 0.0066 1 Compiles CH16:2436MHz 13.74 23.66 0.5 0.0053 1 Compiles TX Mode CH34:2472MHz 13.05 20.18 0.5 0.0045 1 Compiles

FCC ID:Y8AMIP669A Report No.:FC110128N05 1 Report Format Version 0.0.1 FCC TEST REPORT REPORT NO.: FC110128N05 MODEL NO.: MIP669A, ITPW891B(See Item 3.1) RECEIVED: Jan.28, 2011 TESTED: Mar.10~Mar.15, 2011 ISSUED: Mar.18, 2011 APPLICANT: NGAI LIK ELECTRONICS ENTERPRISES LIMITED ADDRESS: FLAT 29-32,8/F., BLOCK B, FOCAL INDUSTRIAL CENTRE, 21 MAN LOK STREET, HUNG HOM, KOWLOON, HONG KONG ISSUED BY: NS Technology Co., Ltd. LAB ADDRESS: Chenwu Industrial Zone, Houjie Town, Dongguan, Guangdong, China This test report consists of 39 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by A2LA, or any government agency. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Test Lab Cert 2951.01 FCC ID:Y8AMIP669A Report No.:FC110128N05 2 Report Format Version 0.0.1 TABLE OF CONTENTS 1. CERTIFICATION .................................................................................................................. 4 2. SUMMARY OF TEST RESULTS.......................................................................................... 5 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 5 3. GENERAL INFORMATION................................................................................................... 6 3.1 GENERAL DESCRIPTION OF EUT ................................................................................ 6 3.2 DESCRIPTION OF TEST MODES .................................................................................. 6 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................................. 7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL.................................. 8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................... 10 3.4 DESCRIPTION OF SUPPORT UNITS ..........................................................................10 4. TEST TYPES AND RESULTS ....................................................................................... 11 4.1 RADIATED EMISSION MEASUREMENT ..................................................................... 11 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................................... 11 4.1.2 TEST INSTRUMENTS ................................................................................................... 12 4.1.3 TEST PROCEDURES ................................................................................................... 13 4.1.4 DEVIATION FROM TEST STANDARD..........................................................................13 4.1.5 TEST SETUP ................................................................................................................. 14 4.1.6 EUT OPERATING CONDITIONS .................................................................................. 14 4.1.7 TEST RESULTS............................................................................................................. 15 4.2 CONDUCTED EMISSION MEASUREMENT ................................................................ 20 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................................. 20 4.2.2 TEST INSTRUMENTS ................................................................................................... 20 4.2.3 TEST PROCEDURES ................................................................................................... 21 4.2.4 DEVIATION FROM TEST STANDARD..........................................................................21 4.2.5 TEST SETUP ................................................................................................................. 22 4.2.6 EUT OPERATING CONDITIONS .................................................................................. 22 4.2.7 TEST RESULTS............................................................................................................. 23 4.3 6dB BANDWIDTH MEASUREMENT.............................................................................25 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .......................................................... 25 4.3.2 TEST INSTRUMENTS ................................................................................................... 25 4.3.3 TEST PROCEDURE ...................................................................................................... 25 4.3.4 DEVIATION FROM TEST STANDARD..........................................................................25 4.3.5 TEST SETUP ................................................................................................................. 26 4.3.6 EUT OPERATING CONDITIONS .................................................................................. 26 4.3.7 TEST RESULTS............................................................................................................. 27 4.4 MAXIMUM OUTPUT POWER ....................................................................................... 29 4.4.1 LIMITS OF MAXIMUM OUTPUT POWER MEASUREMENT ....................................... 29 4.4.2 INSTRUMENTS ............................................................................................................. 29 4.4.3 TEST PROCEDURES ................................................................................................... 29 FCC ID:Y8AMIP669A Report No.:FC110128N05 3 Report Format Version 0.0.1 4.4.4 DEVIATION FROM TEST STANDARD..........................................................................29 4.4.5 TEST SETUP ................................................................................................................. 30 4.4.6 EU…

Text truncated - open the document above for the full version.

1.1. Set-up for conducted emission at the mains terminals test 1.2. Set-up for radiated emission test(30MHz~1000MHz) 1.3. Set-up for radiated emission test(above 1GHz) 1.4. Set-up for Peak output Power Test 1.5. Set-up for 6dB bandwith Test