YCPSTM32WLCDLRF Control Kit

February 2011Doc ID 18433 Rev 11/8 UM1050 User manual STM32W-RFCKIT Low-cost RF control kit for STM32W108xx microcontrollers 1 Introduction The STM32W-RFCKIT low-cost RF control kit is an easy-to-use tool for STM32W108xx RF microcontrollers. This family of microcontrollers integrates a 32-bit ARM® Cortex™-M3 microprocessor and a 2.4 GHz, IEEE 802.15.4-compliant transceiver. The kit demonstrates plug and play 2.4GHz RF point-to-point communications targeting general-purpose wireless control systems. The STM32W-RFCKIT RF control kit provides demonstration applications and documentation which serve as a reference for creating your own applications and re- programming the STM32W108xx microcontroller. You can run the STM32W-RFCKIT RF control kit in several ways using the dedicated software libraries (Simplified MAC, ZigBee RF4CE and ZigBee PRO). This kit provides access to a set of straightforward HAL APIs enabling application engineers to easily develop RF control capabilities such as LEDs, serial communication channels (virtual COM through USB), MEM enabled pointers, etc. Moreover, thanks to the flexibility of STM32W microcontrollers, developers will also be able to use the kit with other available protocol network libraries: MAC based, RF4CE, ZigBee PRO or 6LowPan. This manual provides information about: ■STM32W-RFCKIT RF control kit components ■How to install the related hardware, software and documentation trees ■How to run the preprogrammed demonstration applications Note:For more information, visit the STM32W 32-bit RF microcontroller webpages at www.st.com/stm32w_rfcontrol These webpages provide full access to all STM32W108xx resources (kits, software packages and documents). www.st.com ContentsUM1050 2/8Doc ID 18433 Rev 1 Contents 1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1Kit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1.1Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1.2Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1.3Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2Software libraries and demonstration applications . . . . . . . . . . . . . . . . . . . 4 2.3Kit setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3.1Powering on the boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3.2Installing the ST Virtual COM port driver USB drive . . . . . . . . . . . . . . . . 4 2.3.3Setting up the application serial communication channel . . . . . . . . . . . . 4 3Running the STM32W-RFCKIT RF control kit . . . . . . . . . . . . . . . . . . . . . 5 3.1Installing the STM32W-RFCKIT RF control kit software tree . . . . . . . . . . . 5 3.1.1Building and download the Simple MAC talk demonstration application . 5 3.1.2Basic RF communication using the talk demonstration application . . . . . 6 4STM32W-RFCKIT utilities and software tools . . . . . . . . . . . . . . . . . . . . . 7 4.1stm32w_flasher utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5List of acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 UM1050Getting started Doc ID 18433 Rev 13/8 2 Getting started This section provides a complete description of the STM32W-RFCKIT RF control kit's hardware and software. 2.1 Kit description 2.1.1 Hardware The STM32W-RFCKIT RF control kit's package contains the following hardware components: ●One STM32W108xx MB950 remote application board ●One STM32W108xx MB951 USB dongle Note:For information concerning the STM32W108xx MB950 and MB951 boards, refer to the documentation included with all available software and the documentation tree installer file (see Section 2.2: Software libraries and demonstration applications). 2.1.2 Software The STM32W-RFCKIT RF control kit does not contain any CD-ROMs. 2.1.3 Documentation The STM32W-RFCKIT RF control kit contains a welcome letter which briefly describes its components and targeted applications. Figure 1.MB950 remote application boardFigure 2.MB951 USB dongle Getting startedUM1050 4/8Doc ID 18433 Rev 1 2.2 Software libraries and demonstration applications The following installer files are available on the STM32W 32-bit RF microcontroller webpages: ●ST Simple MAC-1.0.2.0-STM32W108: installer file which provides the STM32W108 Simple MAC software library and demonstration applications targeting point-to-point communication scenarios based on the IEEE 802.15.4 protocol. ●ST ZigBee RF4CE-1.2.0.0-STM32W108: installer file which provides the STM32W108 ZigBee RF4CE software library and demonstration applications for controlling an RF4CE-compliant TV using an RF4CE-compliant remote control. ●EmberZNet-4.3.0.0-STM32W108: installer file which provides the EmberZNet™ 4.3.0 GA software libraries and demonstration applications targeting the mesh network scenarios based on the ZigBee PRO protocol stack. Note:1For a detailed description of software and documentation trees, refer to the related documentation (starting from the HTML index file, that comes with each installer file). 2Each installer file also provides a set of prebuilt binary images (applications and utilities). 3For the most recent installer file versions, visit the STM32W 32-bit RF microcontroller webpages at www.st.com/stm32w_rfcontrol 2.3 Kit setup 2.3.1 Powering on the boards The MB950 application board can be powered as follows: ●Via batteries ●Via USB To power on the MB951 USB dongle, simp…

Text truncated - open the document above for the full version.

Impedance Matching Network RF Transceiver Crystal Oscillator MAC and Baseband GPIO / ADC Timers other periph. Power On Reset Power Manager nRESETVSS VCC STM32W108 Decoupling B953 Embedded PCB Antenna GPIO M 24MHz

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007

Date:2011.5.24 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: YCPSTM32WLCDL To Whom It May Concern: This letter is to ascertain that STMicroelectronics SAS Product RF Control Kit has been the units used for conducting FCC compliance testing, the DoC part will be tested by FCC recognized test lab. If you have any question or concerns, pls. contact us. Sincerely,

FCC Test Report Report No.: RF-D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Attachment 2 External Photographs of EUT FCC Test Report Report No.: RF-D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : A2-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546

FCC Test Report Report No.: RF-D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 0 Attachment 3 Internal Photographs of EUT FCC Test Report Report No.: RF-D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. Page : A3- TEL. : 886-2-25984542 FAX. : 886-2-25984546 1

MB953 Module 1. Hardware Description Impedance Matching Network RF Transceiver Crystal Oscillator MAC and Baseband GPIO / ADC Timers other periph. Power On Reset Power Manager nRESETVSS VCC STM32W108 Decoupling B953 Embedded PCB Antenna GPIO M Fig. 1 Block Diagram of the Module The MB953 Module is low-power, highly sensitivity IEEE 802.15.4 / ZigBee-compliant module. This multi-functional device is based on the STMicroelectronics STM32W108 fully integrated System-on- Chip (STM32W108CBU6x version). This STM32W108 SoC integrates a 2.4 GHz IEEE 802.15.4-compliant transceiver, a 32-bit ARM® Cortex™- M3 microprocessor, Flash and RAM memory, as well as peripherals for use by designers of ZigBee-based systems. The MB953 comes with 128 Kbytes of embedded Flash memory and 8 Kbytes of integrated RAM for data and program storage. The STM32W108 IC offers a number of advanced power management features that enables long battery life. A high-frequency internal RC oscillator allows the processor core to begin code execution quickly upon waking. Various deep sleep modes are available with less than 1 μs power consumption while retaining RAM contents. I/O Peripherals To support user-defined applications, on-chip peripherals include UART, SPI, TWI, ADC, general- purpose timers, and up to 24 GPIOs. Additionally, an integrated voltage regulator, power-on-reset circuit, and sleep timer are available. The STM32W108 IC utilizes standard Serial Wire and JTAG interfaces for powerful software debugging and programming of the ARM Cortex-M3 core. The STM32W108 IC integrates the standard ARM system debug components including Flash Patch and Breakpoint (FPB), Data Watch-point and Trace (DWT), and Instrumentation Trace Macrocell (ITM). May 2011 Doc ID:DZ MD-MB953 MOD rev0. 1 2 Firmware Protocol Stacks Three protocols stacks are available: • RF4CE (Radio Frequency for Consumer Electronics) stack, which is used primarily for a wide range of remotely-controlled audio/visual consumer electronics products.32-bit ARM® Cortex™ -M3 microprocessor • Proprietary stack, which is a robust application user interface package for wireless control and monitoring applications • EmberZNet PRO stack, which is a complete ZigBee protocol software package containing all the elements required for robust and reliable mesh networking applications Figure 4 below shows the a block diagram of the three optional ZigBee stacks Fig. 2 Available protocol stacks. © 2011 DiZiC Co. Ltd. Subject to change without notice.

FCC Test Report Report No.:RF- D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : A-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Maximum Permissible Exposure Evaluation FCC Test Report Report No.:RF- D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : A-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Maximum Permissible Exposure Evaluation Power Density at Specific Separation: S = PG/(4R 2 π) Where S = Maximum power density (mW/cm 2 ) P = Power input to the antenna (mW) G = Numeric power gain of the antenna R = Distance to the center of the antenna = 20 cm Measured maximum output power (P) is -8.99dBm = 0.126mW The Numeric power gain of the antenna (G) is 1.95dB = 1.57 S = (0.126* 1.57) / (4 * 20 2 * π) S = 0.000039 (mW/cm 2 ) The maximum permissible exposure (MPE) for the general population is 1 mW/cm 2 . The power density at 20 cm distance to the center of the antenna does not exceed the 1 mW/cm 2 . Therefore, the exposure condition is compliant with FCC rules.

11 22 33 44 D D C C B B A A DiZiC Co., Ltd.3F, N°4-2, Jin Xi StreetZhong Shan DistrictTaipei City 104TAIWAN Title:Size: Number: Date:File: Revision:Sheet of Time: A4 MB953 2 Layers module PCB antenna A 12/10/2010 1:46:08 PM 1 1 MB953 rev A.SchDoc L23.3nH C612pF C512pF X1 24MHz GND GND C38pF +1V8 C2110nF C201uF R4 180K(1%) GND GND GND GND GND VDDA 1 VDDA 2 RF P 3 RF N 4 VDD RF 5 RF TX ALT P 6 RF TX ALT N 7 VDD IF 8 BIAS R 9 VDDA 10 GPIO21 11 GPIO22 13 GPIO23 14 VREG OUT 15 VDD PADS 16 VDD CORE 17 GPIO7 18 GPIO11 19 GPIO12 20 GPIO0 21 GPIO1 22 VDD PADS 23 GPIO19 34 GPIO20 35 GPIO3 25 GPIO4 26 GPIO5 27 VDD PADS 28 GPIO6 29 GPIO9 30 GPIO10 31 JTCK 32 GPIO18 33 VDDA 45 VDDA 46 OSCB 47 VDD PADS 37 GPIO17 38 VDD MEM 39 GPIO16 40 GPIO15 41 GPIO14 42 GPIO13 43 VDD CORE 44 RSTB 12 GPIO2 24 GPIO8 36 OSCA 48 EPAD IC1STM32W108 +1V2 +1V2 C4470nF GND C210nF GND C110nF GND R610K R1 10R C2210nF GND C1610nF GND R51R C192.2uF GND +1V8 nRST +VBRD +VBRD C18100nF GND C17100nF GND C11100nF GND C7100nF GND 15 423 + - T1WE748-421-245 L1 0R C9 C8 0R GND GND C128pF GND C10 GND 4 2 1 GND 3 FLT1WE748-351-124 GND GPIO10GPIO08GPIO06GPIO09GPIO20GPIO18JTCKGPIO19 1 PA6 1 PB2 1 PC2 1 PC4 1 PB0 1 PC3 1 SWCLK 1 PB1 GPIO04GPIO05GPIO03 1 PA4 1 PA5 1 PA3 1 nRST GPIO14 GPIO15 GPIO13 GPIO16 1 PB6 1 PC0 1 PB7 1 PB5 GPIO12 GPIO11 GPIO07 GPIO00 GPIO01 1 PA7 1 PB4 1 PA1 1 PB3 1 PA0 GPIO02 1 PA2 1 VCC 1 GND GND +VBRD ANT

FCC Test Report Report No.:RF- D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : 1/63 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 FCC Test Report for RF Control Kit Model Number : MB953 FCC ID : YCPSTM32WLCDL Report Number : RF-D230-1103-093 Date of Receipt : March 15, 2011 Date of Report : May 12, 2011 Prepared for STMicroelectronics SAS 190 Avenue Célestin Coq, 13106 Rousset Cedex, France Prepared by Central Research Technology Co. EMC Test Laboratory No.11, Lane41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. NVLAP LAB CODE 200575-0 This report shall not be reproduced, except in full, without the written approval of Central Research Technology Co.. It may be duplicated completely in its entirely for legal use with the permission of the applicant. It should not be used to claim product endorsement by NVLAP, NIST or any U.S. government agency. The test result in the report applies only to the sample tested. FCC Test Report Report No.:RF- D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : 2/63 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Verification of Compliance Equipment under Test : RF Control Kit Model No. : MB953 FCC ID : YCPSTM32WLCDL Manufacturer : DIZIC Co. Ltd. Applicant : STMicroelectronics SAS Address : 190 Avenue Célestin Coq, 13106 Rousset Cedex, France Applicable Standards : 47 CFR part 15, Subpart C Date of Testing : March 15 ~ April 16, 2011 Deviation : N/A Condition of Test Sample : Engineering Sample We, Central Research Technology Co., hereby certify that one sample of the designated product was tested in our facility during the period mentioned above. The test records, data evaluation and Equipment Under Test (EUT) configurations shown in the present report are true and accurate representation of the measurements of the sample’s RF characteristics under the conditions herein specified. The test results show that the EUT as described in the present report is in compliance with the requirements set forth in the standards mentioned above and apply to the tested sample identified in the present report only. The test report shall not be reproduced, except in its entirety, without the written approval of Central Research Technology Co. FCC Test Report Report No.:RF- D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : 3/63 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Contents 1 General Description ..............................................................................................5 1.1 General Description of EUT..................................................................................5 1.2 Applied standards.................................................................................................6 1.3 The Support Units.................................................................................................8 1.4 Layout of Setup.....................................................................................................8 1.5 Test Capability.......................................................................................................8 1.6 Measurement Uncertainty..................................................................................10 2 Maximum Peak Output Power ............................................................................11 2.1 Applied standard................................................................................................. 11 2.2 Test Instruments................................................................................................. 11 2.3 Measurement Procedure....................................................................................12 2.4 Test configuration...............................................................................................12 2.5 Test Data..............................................................................................................13 3 Band Edge ...........................................................................................................17 3.1 Applied standard.................................................................................................17 3.2 Test Instruments.................................................................................................17 3.3 Measurement Procedure....................................................................................17 3.4 Test configuration...............................................................................................17 3.5 Test Data..............................................................................................................18 4 6dB Bandwidth ....................................................................................................26 4.1 Applied standard.................................................................................................26 4.2 Test Instruments.................................................................................................26 4.3 Measurement Procedure....................................................................................27 4.4 Test configuration...............................................................................................27 4.5 Test Data..............................................................................................................28 5 Power Spectral Density ......................................................................................30 5.1 Applied standard.................................................................................................30 5.2 Test Instruments.................................................................................................30 5.3 Measurement Procedure..................................................................................…

Text truncated - open the document above for the full version.

FCC Test Report Report No.: RF- D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : A1-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Attachment 1 Photographs of the Test Configurations FCC Test Report Report No.: RF- D230-1103-093 CENTRAL RESEARCH TECHNOLOGY CO. Page : A1-1 No. 11, Lane 41, Fushuen St., Jungshan Chiu, Taipei, Taiwan, 104, R.O.C. TEL. : 886-2-25984542 FAX. : 886-2-25984546 Radiated Emission Measurement