YJ709472-81539Cordless inspection camera

1 English The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non- skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. d) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. e) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Defi nitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury . WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury . CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury . NOTICE: indicates a practice not related to personal injury which, if not avoided, may result in property damage . IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WALT TOOL, CALL US TOLL FREE AT: 1-800-4-D E WALT (1-800-433-9258). WARNING: To reduce the risk of injury, read the instruction manual. General Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE 2 English POWER TOOL USE AND CARE a) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. b) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. c) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. d) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. e) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. BATTERY TOOL USE AND CARE a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. c) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Safety Information for Inspection Cameras WARNING: Do not disassemble or modify the inspection camera. There are no user serviceable parts inside. Serious eye injury could result. • Do not operate the inspection camera in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust . Power tools create sparks which may ignite the dust or fumes. • The inspection camera should only be used with specifically designated D E WALT batteries. Use of any other batteries may create a risk of fire. • Store the inspection camera out of reach of children and other untrained persons . Tools are dangerous in the hands of untrained users. • Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified 3 English personnel may result in injury. To locate your nearest D E WALT service center call 1-800-4-D E WALT (1-800-433-9258) or go to http://www.dewalt.com on the Internet. • Do not disassemble the inspection camera. There are no user serviceable parts inside. • Do not allow the inspection camera cable to come in contact with live wires. Shut off circuit breakers to the entire area to avoid i…

Text truncated - open the document above for the full version.

Rf-",-160, Issue 02 Declaration of Authorization W e Name Stanley Black & Decker Address 701 East Joppa Road, Towson, City: M aryland Country United States Declare that: Name Representative of agent: Ms. Cathy Wang Agent C ompany name: Neutron Engineering, Inc. Address: NO .3 Jinshagang 1 st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification, c ompleting and signing of the RF-731 form for Certification of the following product(s): Product description: Cordless inspection camera Type designation: 09472-81539 Trademark: DEWALT on our behalf. Date: 2010-8 -5 City: Maryland Name: Mr. Scott Kolodziejski Function: Manager Signature ....~ .uf.-£....... ..... Notes: (1). Required f or FCC application (2). For FCC it must be the Grantee Code "owner' or the authorized agent.

FCC, Request for non-disclosure Date 10-Aug-09 RF_501, Issue 5 Page 1 of 1 Company Name: Address: City Country: Stanley Black & Decker 701 East Joppa Road, Towson Maryland United States To: Telefication B.V , Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID YJ709472·81539 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section OA59(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application D Bill(s) of Material [2S] Block Diagrams [2S] Operational Description [2S] Schematic Diagram s D Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section OA57(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission's policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1): D Internal Photos D User's Manual D Test Set-up Photos D External Photos Justification: Planned Release Date STC (notes 2, 3, 4, 5) Date 2010-08-05 Name and signature of applicant Mr Scott Kolodziejski _~(j)f~ Notes: 1) A document or type of document can only have ONE type of confidentialityI 2) Short-Term confidentiality is in principle for 45 days from date of grant, it ca n be extended max 3 times (total time 180 days max)1 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telerication does not remind you of thisl 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC penod

Neutron Engineering Inc. Project No.: 1006C293 Page 2 of 13 TX Sample 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 2 of 13 TX Sample 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 3 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 3 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 4 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 4 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 5 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 5 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 6 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 6 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 7 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 7 of 13 1006C293 1006C293

Neutron Engineering Inc. Project No.: 1006C293 Page 8 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 8 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 9 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 9 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 10 of 13 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 11 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 11 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 12 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 12 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 13 of 13 1006C293 1006C293 Neutron Engineering Inc. Project No.: 1006C293 Page 13 of 13 1006C293 1006C293

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 2 of 35 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 3 of 35 Table of Contents Page 1 . CERTIFICATION 5 2 . SUMMARY OF TEST RESULTS 6 2.1 TEST FACILITY 7 2.2 MEASUREMENT UNCERTAINTY 7 3 . GENERAL INFORMATION 8 3.1 GENERAL DESCRIPTION OF EUT 8 3.2 DESCRIPTION OF TEST MODES 10 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 11 3.4 DESCRIPTION OF SUPPORT UNITS 12 4 . EMC EMISSION TEST 13 4.1 CONDUCTED EMISSION MEASUREMENT 13 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 4.1.2 MEASUREMENT INSTRUMENTS LIST 13 4.1.3 TEST PROCEDURE 14 4.1.4 DEVIATION FROM TEST STANDARD 14 4.1.5 TEST SETUP 14 4.1.6 EUT OPERATING CONDITIONS 14 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 17 4.2.1 RADIATED EMISSION LIMITS 17 4.2.2 MEASUREMENT INSTRUMENTS LIST 18 4.2.3 TEST PROCEDURE 19 4.2.4 DEVIATION FROM TEST STANDARD 19 4.2.5 TEST SETUP 20 4.2.6 EUT OPERATING CONDITIONS 20 4.2.7 TEST RESULTS (BETWEEN 30 – 1000 MHz) 21 4.2.8 TEST RESULTS (ABOVE 1000 MHz) 23 4.2.9 TEST RESULTS (2400 – 2483.5 MHz) 27 5 . BANDWIDTH TEST 28 5.1 MEASUREMENT INSTRUMENTS LIST 28 5.2 TEST PROCEDURE 28 5.3 DEVIATION FROM STANDARD 28 5.4 TEST SETUP 28 5.5 EUT OPERATION CONDITIONS 28 5.6 TEST RESULTS 29 6 . ANTENNA CONDUCTED SPURIOUS EMISSION 30 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 4 of 35 Table of Contents Page 6.1 APPLIED PROCEDURES / LIMIT 30 6.1.1 MEASUREMENT INSTRUMENTS LIST 30 6.1.2 TEST PROCEDURE 30 6.1.3 DEVIATION FROM STANDARD 30 6.1.4 TEST SETUP 30 6.1.5 EUT OPERATION CONDITIONS 30 6.1.6 TEST RESULTS 31 7 . EUT TEST PHOTO 34 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 5 of 35 1. CERTIFICATION E q u i p m e n t : Cordless inspection camera Brand Name : DEWALT Model Name. : 09472;81539 Applicant : Stanley Black & Decker Date of Test : Jul. 14, 2010 ~ Jul. 27, 2010 T e s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.249)/ ANSI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-1006C293) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 6 of 35 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.249) Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.209 Radiated Emission PASS 15.249 Radiated Spurious Emission PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report (2) The EUT used new battery. Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 7 of 35 2.1 TEST FACILITY The test facilities used to collect the test data in this report is DG-C03/CB03at the location of No.3,Jinshagang 1st Road, ShiXia, Dalang Town,Dong Guan, China.523792 Neutron's test firm number is 319330 2.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 A. Conducted Measurement : Test Site Method Measurement Frequency Range U，(dB) NOTE DG-C03 CISPR 150 KHz ~ 30MHz 1.94 B. Radiated Measurement : Test Site Method Measurement Frequency Range Ant. H / V U，(dB) NOTE 30MHz ~ 200MHz V 2.48 30MHz ~ 200MHz H 2.16 200MHz ~ 1,000MHz V 2.50 CB03 CISPR 200MHz ~ 1,000MHz H 2.66 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 8 of 35 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Equipment Cordless inspection camera Brand Name DEWALT Model Name. 09472;81539 OEM Brand/Model Name N/A Model Difference The difference is that the hose program (9mm/17mm) RF Module is the same. Product Description The EUT is a Cordless inspection camera . Product Type Low Power Communication Device Operation Frequency: 2468 MHz Modulation Type: GFSK Date rate: 1Mbps Number Of Channel 1CH .Please see Note 2. Antenna Designation: Integral antenna Antenna Gain(Peak) 1.0 dBi Output Power: 93.27dBuV/m (AV Max.) More…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 34 of 35 7. EUT TEST PHOTO Conducted Measurement Photos Charger for battery Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 34 of 35 7. EUT TEST PHOTO Conducted Measurement Photos Charger for battery Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 35 of 35 Radiated Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-1006C293 Page 35 of 35 Radiated Measurement Photos