YLF7S6300Wi-Fi 6/6E Sensor

EYE SENSOR DEPLOYMENT GUIDE 7SIGNAL 7S6300 Wi-Fi 6/6E Sensor Deployment Guide Draft Prerelease 0.94 Preface i 7SIGNAL, Inc., 6155 Rockside Road, Suite 110, Independence, Ohio 44131, USA, 216- 777-2900, [email protected], www.7signal.com 7SIGNAL 7S6300 Deployment Guide Draft Prerelease 0.94 PREFACE Document scope This document is aimed at people familiarizing themselves with the 7Signal Sensor system before deployment and to aid with the deployment. After completion of the steps in this document, the 7Signal Sensor should be installed, up and running and ready for Wi-Fi performance management. This document does not describe how the software operates, how to configure testing or how to read the measurements. The actual use of 7Signal Sensor applications is explained in documents 7signal Sapphire Carat User Guide, 7signal Sapphire Analyzer User Guide and 7signal Sapphire EyeQ and REST API User Guide. FCC: FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This equipment is a slave device, the device does not detect radar and does not support ad-hoc operation in the DFS band. FCC regulations restrict the operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Preface ii 7SIGNAL, Inc., 6155 Rockside Road, Suite 110, Independence, Ohio 44131, USA, 216- 777-2900, [email protected], www.7signal.com 7SIGNAL 7S6300 Deployment Guide Draft Prerelease 0.94 ISED : Industry Canada Equipment Standard for Digital Equipment (ICES) – Canada Compliance Statement This Class B digital apparatus complies with Canadian ICES‐003. CAN ICES-003 (B)/NMB-003(B) Cet appareil numérique de la classe B est conforme à la norme NMB‐003 du Canada. ICES-003 CAN ICES-003(B) / NMB-003(B) Innovation, Science and Economic Development Canada (ISED) Compliance Statement This device complies with ISED’s license-exempt RSS standard(s). Cet appareil est conforme aux normes RSS exemptes de licence d'ISED. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Caution: User should also be advised that: (i) the device for operation in the band 5150‐5250 MHz is only for indoor use to reduce the potential for harmful interference to co‐channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250‐5350 MHz and 5470‐ 5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725‐5825 MHz shall comply with the e.i.r.p. limits specified for point‐to‐point and non point‐to‐point operation as appropriate. High‐power radars are allocated as primary users (i.e. priority users) of the bands 5250‐5350 MHz and 5650‐5850 MHz and that these radars could cause interference and/or damage to LE‐LAN devices. Les utilisateurs devraient aussi être avisés que (i) les dispositifs fonctionnant dans la bande 5150‐5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250‐5350 MHz et 5470‐5725MHz doit se conformer à la limite de p.i.r.e.; (iii) le gain maximal d’antenne…

Text truncated - open the document above for the full version.

Date: October 17, 2023 Federal Communications Commission Authorization and Evaluation Division FCC ID: YLF7S6300 Product description: Wi-Fi 6/6E Sensor We, 7signal attest that this device under FCC ID: YLF7S6300 complies with device protocol requirements and operational restrictions for Indoor Client 6XD: 1. Device Protocol Attestation Statement: a. Contention-Based Protocol, as demonstrated in the test report, is permanently embedded in the module and is not host-dependent. b. The device will only associate and connect with a low-power indoor access point or subordinate device and never directly connect to other client devices. c. This device will always initiate transmission under the control of a low-power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. d. Transmissions will be lower or equal to the power advertised by the indoor low- power access point or subordinate and never above the maximum output power allowed by the FCC grant for equipment class 6XD. e. Contention-based protocol as demonstrated in the test report is permanently embedded in the module and is not host-dependent. This device is prohibited for control of or communications with unmanned aircraft systems, including drones. Best regards ------------------------------------------------------ Ted Schneider / CTO 7signal

Certification Application Attestation Statements 7signal 6155 Rockside Road, Suite 110, Independence, Ohio 44131 United States Subject: FCC ID: YLF7S6300 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) 7signal certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) 7signal certifies that, as of the date of the filing of this application, the applicant - is / - is not (3) identified on the Covered List as an entity producing “covered” equipment. Date: October 17, 2023 City: Independence Name (2) : Ted Schneider Function: CTO Telephone number: 216-777-2900 Email address: [email protected] Signature: 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . (2): For FCC it must be the Grantee Code “owner” or the authorized agent. (3): double click on the appropriate box and select ‘’checked” then “OK”

U.S. Agent DesignaƟon for Service of Process TO: Federal CommunicaƟons Commission AuthorizaƟon and EvaluaƟon Division 7435 Oakland Mills Rd Columbia MD 21046-1609 ATTENTION: FCC CerƟficaƟon – SecƟon 2.911(d)(7) InformaƟon This leƩer is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year aŌer terminaƟng all markeƟng and importaƟon OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent informaƟon changes. Applicant: Company name: 7SIGNAL, Inc. FRN: 0034269696 Contact person name: Ted Schneider Street address: 6155 Rockside Rd. Suite 110, City/ZIP/State Independence, 44131, Ohio Telephone number: 216-777-2900 Email address: [email protected] Signature: Date: October 20, 2023

Date: July 24, 2023 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: YLF7S6300 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below: Type of Confidentiality Requested Exhibit ☒ Permanent Block Diagrams ☒ Permanent Operation Description/NII Security info. ☒ Permanent Schematics The above materials contain trade secrets and proprietary information not customarily Released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Type of Confidentiality Requested Exhibit ☒ Short Term External Photos ☒ Short Term Internal Photos ☒ Short Term Test Setup Photos ☒ Short Term User’s Manual Note: Release date of short term confidentiality is 180 days from grant date marked. (FCC must be informed when marketing begins earlier.) Sincerely, ------------------------------------------------------ Ted Schneider / CTO [email protected]

Date: October 17, 2023 Product: Wi-Fi 6/6E Sensor Model: 7S6300 FCC ID: YLF7S6300 Declaration Letter for Data Reuse This application is intended to reuse the test data from FCC ID: A8J-ECW336, certified on 07/08/2022, due to the fact that this products is hardware-wise identical and only the following changes have been made: 7S6300 (FCC ID: YLF7S6300), use the same MCU chipset(IPQ8072A), share the same chipset baseline, hardware design, support same bands, the difference is only on software version change from master mode to slave mode. Base on above condition, below are summary table for data reuse and spot checks according to KDB 484596 D01. DTS Test Item Data Reused Remark Conducted Emission Yes N/A Radiated Band Edge Yes Verify worst-case channel Radiated Spurious Emission Yes Verify worst-case channel 6dB Bandwidth Yes N/A Peak Power Output Yes Verify all output power RF Antenna Conducted Test Yes N/A Power Spectral Density Yes N/A Duty Cycle Yes N/A UNII-1, 3 Test Item Data Reused Remark Conducted Emission No Re-test Radiated Band Edge No Re-test Radiated Spurious Emission No Re-test 6dB / Occupied Bandwidth No Re-test Maximum Conducted Output Power No Re-test Power Spectral Density No Re-test Duty Cycle No Re-test UNII-2A, 2C Test Item Data Reused Remark Conducted Emission Yes N/A Radiated Band Edge Yes Verify worst-case channel Radiated Spurious Emission Yes Verify worst-case channel Occupied Bandwidth Yes N/A Maximum Conducted Output Power Yes Verify all output power Power Spectral Density Yes N/A Duty Cycle Yes N/A DFS No Re-test slave mode Wi-Fi 6E Test Item Data Reused Remark Conducted Emission No Re-test Radiated Band Edge No Re-test Radiated Spurious Emission No Re-test Occupied Bandwidth No Re-test Transmit Output Power No Re-test Power Spectral Density No Re-test In-Band Emission (Mask) No Re-test Contention Based Protocol No Re-test Duty Cycle No Re-test Sincerely, ------------------------------------------------------ Ted Schneider / CTO 7signal

Declaration of Authorization We Name: 7signal Address: 6155 Rockside Road, Suite 110, City: Independence State: Ohio 44131 Country: United States Declare that: Name Representative of agent: Stanley Wu Agent Company name: DEKRA Testing and Certification Co., Ltd. Address: No. 26, Huaya 1 st Rd., Guishan Dist., City: Taoyuan City 33341 Country: Taiwan. is authorized to apply for FCC certifications of the following product(s): Product Name: Wi-Fi 6/6E Sensor Model: 7S6300 FCC ID: YLF7S6300 Trademark: 7SIGNAL, Inc. on our behalf. Date: October 17, 2023 Name: Ted Schneider Function: CTO Email: [email protected] Signature:

Report No.: 2360570R-Product Photos Page: 1 of 3 (1) EUT Photo (2) EUT Photo Report No.: 2360570R-Product Photos Page: 2 of 3 (3) EUT Photo (4) EUT Photo Report No.: 2360570R-Product Photos Page: 3 of 3 (5) EUT Photo (6) EUT Photo

2023/08/09 機構外觀課 Michael Bear 7S6300 emplus Technologies, Inc. Ted 機種名稱 尺寸刀模料號參考 1 1 - Dimension : 61.4 *51.4 mm - Tolerance : ±0.1 mm - Ink : 單色黑 - Coating: Printable Matt Polyester 打字霧P - Material : 50 番反銀龍+一般黏膠 +打字霧膜 Code : HTLSMI50 Adhesive : △ 黏著力 Peel Adhesion: 0.8 kgf/25mm ↑ Coating : 25番霧面無鹵打印 PET △ 黏著力 Peel Adhesion: 0.6 ↑ kgf / 25mm △ 適用溫度Service Temperature: ≧ 110 °C 15.9 15.9 15.9 15.9 + 34.8mm 35mm 34.8mm 35mm 61.4 3-1.8R 51.4 61.4 51.4 ® Wi-Fi 6/6E Sensor Model : 7S6300 Rating: 12V 2.5A 802.3at PoE+ FCC ID: YLF7S6300 IC: 11766A-7S6300 CAN ICES-3(B)/NMB-3(B)

±Redcolorfor reference and willbe printedby factory. 61.4 3-1.8R 51.4 NOTE - 公差部分不符合左列標準 。 - 印刷如有不清、斷字或滲墨現象 。 - 印刷色如與PANTONE色不符合 。 - 印刷位置與圖比例印刷不符合 。 ※廠商須無條件重新製作! 6710A6873591 6710A6873590 2023/10/03 機構外觀課 Michael Bear emplus Technologies, Inc. Ted 1 1 機種名稱 參考料號 7S6300 - Dimension : 61.4 *51.4 mm - Tolerance : ±0.1 mm - Ink : 單色黑 - Coating: Printable Matt Polyester 打字霧P - Material : 50 番反銀龍+一般黏膠 +打字霧膜 Code : HTLSMI50 Adhesive : △ 黏著力 Peel Adhesion: 0.8 kgf/25mm ↑ Coating : 25番霧面無鹵打印 PET △ 黏著力 Peel Adhesion: 0.6 ↑ kgf / 25mm △ 適用溫度Service Temperature: ≧ 110 °C ® Wi-Fi 6/6E Sensor Model: 7S6300 Rating: 12V 2.5A 802.3at PoE+ FCC ID: YLF7S6300 IC: 11766A-7S6300 CAN ICES-003(B)/NMB-003(B) 7SIGNAL, Inc. 6155 Rockside Road, Suite 110, Independence, Ohio 44131, USA

Report No.: 2360570R-Product Photos Page: 1 of 21 (1) EUT Photo (2) EUT Photo Report No.: 2360570R-Product Photos Page: 2 of 21 (3) EUT Photo (4) EUT Photo Report No.: 2360570R-Product Photos Page: 3 of 21 (5) EUT Photo (6) EUT Photo Report No.: 2360570R-Product Photos Page: 4 of 21 (7) EUT Photo (8) EUT Photo Report No.: 2360570R-Product Photos Page: 5 of 21 (9) EUT Photo (10) EUT Photo Report No.: 2360570R-Product Photos Page: 6 of 21 (11) EUT Photo (12) EUT Photo Report No.: 2360570R-Product Photos Page: 7 of 21 (13) EUT Photo (14) EUT Photo Report No.: 2360570R-Product Photos Page: 8 of 21 (15) EUT Photo (16) EUT Photo Report No.: 2360570R-Product Photos Page: 9 of 21 (17) EUT Photo (18) EUT Photo Report No.: 2360570R-Product Photos Page: 10 of 21 (19) EUT Photo (20) EUT Photo Report No.: 2360570R-Product Photos Page: 11 of 21 (21) EUT Photo (22) EUT Photo Report No.: 2360570R-Product Photos Page: 12 of 21 (23) EUT Photo (24) EUT Photo Report No.: 2360570R-Product Photos Page: 13 of 21 (25) EUT Photo (26) EUT Photo Report No.: 2360570R-Product Photos Page: 14 of 21 (27) EUT Photo (28) EUT Photo Report No.: 2360570R-Product Photos Page: 15 of 21 (29) EUT Photo (30) EUT Photo Report No.: 2360570R-Product Photos Page: 16 of 21 (31) EUT Photo (32) EUT Photo Report No.: 2360570R-Product Photos Page: 17 of 21 (33) EUT Photo (34) EUT Photo Report No.: 2360570R-Product Photos Page: 18 of 21 (35) EUT Photo (36) EUT Photo Report No.: 2360570R-Product Photos Page: 19 of 21 (37) EUT Photo (38) EUT Photo Report No.: 2360570R-Product Photos Page: 20 of 21 (39) EUT Photo (40) EUT Photo Report No.: 2360570R-Product Photos Page: 21 of 21 (41) EUT Photo (42) EUT Photo

Report No.: 2360570R-RFUSV17S-A Page: 1 of 8 Test report No.: 2360570R-RFUSV17S-A RF Exposure Report Product Name Wi-Fi 6/6E Sensor Trademark 7SIGNAL, Inc. Model and /or type reference 7S6300 FCC ID YLF7S6300 Applicant ́s name / address 7signal 6155 Rockside Road, Suite 110, Independence, Ohio 44131, United States Manufacturer ́s name 7SIGNAL, Inc. Test method requested, standard KDB 447498 D01 v06 Minimum test separation distance ≥ 20 cm For low power devices Verdict Summary IN COMPLIANCE Documented By (Senior Project Specialist / Genie Chang) Tested By (Senior Engineer / Alan Chen) Approved By (Manager / Tim Sung) Date of Receipt 2023/06/17 Date of Issue 2023/09/05 Report Version V1.0 Report No.: 2360570R-RFUSV17S-A Page: 2 of 8 Competences and Guarantees DEKRA is a testing laboratory competent to carry out the tests described in this report. In order to assure the traceability to other national and international laboratories, DEKRA has a calibration and maintenance program for its measurement equipment. DEKRA guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated in the report and it is based on the knowledge and technical facilities available at DEKRA at the time of performance of the test. DEKRA is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Test Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA. General conditions 1. The test results relate only to the samples tested. 2. The test results shown in the test report are traceable to the national/international standard through the calibration report of the equipment and evaluated measurement uncertainty herein. 3. This report must not be used to claim product endorsement by TAF or any agency of the government. 4. The test report shall not be reproduced without the written approval of DEKRA Testing and Certification Co., Ltd. 5. Measurement uncertainties evaluated for each testing system and associated connections are given here to provide the system information for reference. Compliance determinations do not take into account measurement uncertainties for each testing system, but are based on the results of the compliance measurement. Report No.: 2360570R-RFUSV17S-A Page: 3 of 8 Revision History Report No. Ve r s i o n Description Issued Date 2360570R-RFUSV17S-A V1.0 Initial issue of report. 2023/09/05 Report No.: 2360570R-RFUSV17S-A Page: 4 of 8 1. General Information 1.1. EUT Description Product Name Wi-Fi 6/6E Sensor Trademark 7SIGNAL, Inc. Model and /or type reference 7S6300 Note: For more detailed information please refer to report No.: 2360570R-RFUSV01S-A, 2360570R-RFUSV03S-A, 2360570R-RFUSV03S-B and 2360570R-RFUSV18S-A. Report No.: 2360570R-RFUSV17S-A Page: 5 of 8 2. Test Facility USA FCC Registration Number: TW0033 Canada CAB Identifier Number: TW3023 / Company Number: 26930 Site Description Accredited by TAF Accredited Number: 3023 Test Laboratory DEKRA Testing and Certification Co., Ltd. Linkou Laboratory Address No.5-22, Ruishukeng Linkou District, New Taipei City, 24451, Taiwan, R.O.C Performed Location No. 26, Huaya 1st Rd., Guishan Dist.,Taoyuan City 333411, Taiwan, R.O.C. Phone Number +886-3-275-7255 Fax Number +886-3-327-8031 Report No.: 2360570R-RFUSV17S-A Page: 6 of 8 3. RF Exposure Evaluation 3.1. Standard Applicable According to KDB 447498 D01 (7.1), A minimum test separation distance ≥ 20 cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. 3.2. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 0.3-3.0 614 1.63 *(100) 6 3.0-30 1842/f 4.89/f *(900/f2) 6 30-300 61.4 0.163 1.0 6 300-1,500 f/300 6 1,500-100,000 5 6 (B) Limits for General Population/ Uncontrolled Exposures 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f2) 30 30-300 27.5 0.073 0.2 30 300-1,500 f/1500 30 1,500-100,000 1.0 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneously transmitting antennas incorporated in a host device is ≤ 1.0 Report No.: 2360570R-RFUSV17S-A Page: 7 of 8 3.3. Test Result of RF Exposure Evaluation Product Wi-Fi 6/6E Sensor Test Item RF Exposure Evaluation CDD Mode Band Frequency (MHz) E.I.R.P (dBm) E.I.R.P (mW) Power Density at R = 20 cm (mW/cm2) Limit (mW/cm2) 2.4 GHz 2437 30.44 1106.624 0.220 1 5 GHz 5825 29.46 883.080 0.176 1 6 GHz 6345 14.40 27.542 0.005 1 Note: The conducted output power is refer to report No.: 2360570R-RFUSV01S-A, 2360570R-RFUSV03S-A and 2360570R-RFUSV03S-B from the DEKRA. Calculations for Multi-Transmitter Wo r s t C a s e Mode Maximum E.I.R.P (dBm) Power Density (mW/cm 2 ) Power Density Limit (mW/cm 2 ) Safety Distance (cm) Ratios Result Limit 2.4G WLAN 30.44 0.220 1 20 0.220 0.401 1 5G WLAN 29.46 0.176 1 0.176 6G WLAN 14.40 0.005 1 0.005 Ratios = Power Density / Power Density Limit Report No.: 2360570R-RFUSV17S-A Page: 8 of 8 Beamforming Mode Band Frequenc…

Text truncated - open the document above for the full version.

7S6300 Antenna Test Report CustomerEnGenius Project7S6300 Project Description 2.4G antenna *4 5G antenna *4 6G antenna *4 Date2023/08/11 Prepared byKenny CheckedTony Report VersionA01 Executive Summary •Purpose Antenna verification for 7S6300 device, result as following. •Agenda –Placement and Specification –Return Loss & Isolation –Radiation Pattern –Combine Pattern –Efficiency and Gain Return Loss Return Loss Freq. (MHz)2G12G22G32G4 2400 -14.96-14.52-12.91-19.54 2450 -15.35-24.73-19.33-14.22 2500 -13.72-14.43-13.08-11.79 Return Loss Return Loss Freq. (MHz)5G15G25G35G46G16G26G36G4 5150 -15.01-17.19-17.00-12.23-10.20-23.85-8.66-9.94 5500 -23.72-15.69-17.89-15.58-14.16-18.63-10.41-11.03 5850 -15.79-14.46-34.29-14.65-15.03-19.09-13.24-21.94 5925 -13.96-12.64-23.00-15.06-15.31-20.92-12.62-20.04 6500 -13.90-13.95-20.22-12.77-10.46-18.62-13.97-16.86 7125 -14.67-13.56-12.23-17.97-18.07-14.90-16.46-10.25 Isolation Isolation Freq. (MHz)2G1-2G22G1-2G32G1-2G42G2-2G32G2-2G42G3-2G4 2400 -25.38-27.61-24.98-19.48-26.34-21.87 2450 -23.25-23.74-26.36-15.69-26.96-25.09 2500 -21.57-23.90-26.82-15.53-26.37-24.99 Isolation Isolation Freq. (MHz)5G1-5G25G1-5G35G1-5G45G2-5G35G2-5G45G3-5G4 5150 -55.18-38.14-31.13-35.10-36.76-27.30 5500 -37.20-39.66-25.61-32.25-33.94-29.10 5850 -33.94-35.35-28.77-31.76-48.86-32.08 Isolation Isolation Freq. (MHz)6G1-6G26G1-6G36G1-6G46G2-6G36G2-6G46G3-6G4 5925 -20.62-30.79-37.48-41.12-37.63-22.95 6500 -32.93-45.38-34.18-37.39-52.77-22.60 7125 -28.08-53.82-35.38-39.52-49.15-23.97 Isolation Isolation Freq. (MHz) 5G1-6G15G1-6G25G1-6G35G1-6G45G2-6G15G2-6G25G2-6G35G2-6G4 5150 -32.71-27.97-32.29-42.44-45.91-41.14-28.48-26.41 5500 -35.88-32.18-33.59-38.20-53.21-41.13-28.24-36.38 5850 -32.14-61.19-29.69-37.25-47.72-39.00-30.09-44.67 5925 -32.12-42.92-31.54-35.75-47.92-43.37-32.99-33.40 6500 -33.20-33.21-38.90-31.06-37.80-43.71-33.02-29.60 7125 -47.95-37.07-29.60-33.98-53.67-46.14-31.80-30.19 Isolation Isolation Freq. (MHz) 5G3-6G15G3-6G25G3-6G35G3-6G45G4-6G15G4-6G25G4-6G35G4-6G4 5150 -36.74-34.72-45.10-38.06-33.44-49.43-28.86-41.17 5500 -37.92-37.23-38.99-33.42-27.26-39.81-33.51-36.64 5850 -42.83-45.49-35.03-32.40-32.09-36.73-28.99-34.25 5925 -37.70-43.91-37.72-35.42-31.72-40.45-31.22-33.65 6500 -40.10-40.52-32.31-28.62-34.41-30.00-44.07-35.16 7125 -44.90-37.61-33.97-31.48-37.95-35.84-35.53-41.02 2D Radiation Pattern – 2G1 @ 2.45GHz Front side LED Front side LED I/O port 2G1 I/O port X Z Y LEDI/O port I/O port 2D Radiation Pattern – 2G2 @ 2.45GHz Front side LED I/O port 2G2 X Z Y Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 2G3 @ 2.45GHz Front side LED I/O port 2G3 X Z Y Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 2G4 @ 2.45GHz Front side LED I/O port 2G4 X Z Y Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 5G1 @ 5.55GHz 5G1 X Z Y Front side LED I/O port Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 5G2 @ 5.55GHz 5G2 X Z Y Front side LED I/O port Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 5G3 @ 5.55GHz 5G3 X Z Y Front side LED I/O port Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 5G4 @ 5.55GHz 5G4 X Z Y Front side LED I/O port Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 6G1 @ 6.5GHz Front side LED I/O port 6G1 X Z Y Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 6G2 @ 6.5GHz Front side LED I/O port 6G2 X Z Y Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 6G3 @ 6.5GHz Front side LED I/O port 6G3 X Z Y Front side LED I/O port LEDI/O port I/O port 2D Radiation Pattern – 6G4 @ 6.5GHz Front side LED I/O port X Z Y 6G4 Front side LED I/O port LEDI/O port I/O port Combine pattern – 2G @ 2.45 GHz +Y +X +X +Z +Y +Z LEDI/O port LED I/O port Front side I/O port LED I/O port Front side Combine pattern – 5G @ 5.55 GHz +Y +X +X +Z +Y +Z LEDI/O port LED I/O port Front side I/O port LED I/O port Front side Combine pattern – 6G @ 6.5 GHz +Y +X +X +Z +Y +Z LEDI/O port LED I/O port Front side I/O port LED I/O port Front side Antenna Efficiency and Gain Antenna Performance 2G12G22G32G4 Freq. (MHz) Peak Gain (dBi) Peak Gain (dBi) Peak Gain (dBi) Peak Gain (dBi) Efficiency (%)Efficiency (%)Efficiency (%)Efficiency (%) 240061.73.0060.73.5163.63.8964.82.22 2450 67.23.3067.54.1162.53.7172.02.90 250069.34.0772.14.2663.73.8073.93.15 Antenna Performance 5G15G25G35G4 Freq. (MHz) Peak Gain (dBi) Peak Gain (dBi) Peak Gain (dBi) Peak Gain (dBi) Efficiency (%)Efficiency (%)Efficiency (%)Efficiency (%) 515061.24.8761.84.0152.64.3653.13.59 550059.84.7358.22.5553.34.4953.53.18 585060.35.0961.53.0454.34.5656.44.01 Antenna Performance 6G16G26G36G4 Freq. (MHz) Peak Gain (dBi) Peak Gain (dBi) Peak Gain (dBi) Peak Gain (dBi) Efficiency (%)Efficiency (%)Efficiency (%)Efficiency (%) 592555.65.3060.84.6655.84.6857.15.44 650055.23.7157.54.7455.14.4457.55.38 7125 65.75.0653.83.9662.25.4358.45.48

Report No.: 2360570R-RFUSV03S-B Page: 1 of 149 Test report No.: 2360570R-RFUSV03S-B TEST REPORT Product Name Wi-Fi 6/6E Sensor Trademark 7SIGNAL, Inc. Model and /or type reference 7S6300 FCC ID YLF7S6300 Applicant ́s name / address 7signal 6155 Rockside Road, Suite 110, Independence, Ohio 44131, United States Manufacturer ́s name 7SIGNAL, Inc. Test method requested, standard FCC CFR Title 47 Part 15 Subpart E ANSI C63.4: 2014, ANSI C63.10: 2013 KDB Publication 987594, KDB Publication 789033 Verdict Summary IN COMPLIANCE Documented By (Senior Project Specialist / Genie Chang) Tested By (Senior Engineer / Ivan Chuang) Tested By (Senior Engineer / Alan Chen) Date of Receipt 2023/06/17 Date of Issue 2023/09/05 Report Version V1.0 Report No.: 2360570R-RFUSV03S-B Page: 2 of 149 INDEX Page 1. Summary of Reference Test Data ................................................................................................... 6 1.1. Introduction ............................................................................................................................................. 6 1.2. Difference Description ............................................................................................................................ 6 2. General Information ........................................................................................................................ 7 2.1. EUT Description .....…

Text truncated - open the document above for the full version.