YLI720002011BColor Effects Remote Control

USE AND CARE INSTRUCTIONS • When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water. • If the product is placed on a tree, the tree should be well secured and stable. • Before using, or reusing, inspect product carefully. Discard any products that have cut, damaged or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire. • When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections and wires. • When not in use, store neatly in a cool, dry location protected from sunlight. Install Class 2 Power Supply To String: NOTE: Use only this GE branded, Class 2 Power Supply, Model SA3A-050-3000, manufactured by TDC that was provided with this product. DO NOT use this adapter with any other product. 1. Remove the Power Supply from its packing box. 2. The LED string is fitted with a 2-pronged fitting. 3. Align the notch in fitting with the inner tab on end of Power Supply {Fig. 1} 4. Fully insert the fitting into the Power Supply {Fig. 2} 5. Screw the collar completely onto the Power Supply turning clockwise {Fig. 3} Operate the Remote: 1. Remove the remote from its packing box. Note: The batteries were pre-installed at the factory. 2. Pull out the plastic film from the battery cover to energize the remote. {Fig. 1} 3. The remote has two buttons {Fig. 2}: a. ON/OFF – Press to turn the set OFF; press again to turn the set ON. b. Function – Press to change the light pattern to the next mode. NOTES: 1. Fully inserting the plug on the Class 2 Power Supply into a working outlet energizes the string. 2. When using the remote to turn ON your set there may be up to a 2 second delay before the light pattern starts working. 3. To change light patterns it is recommended to wait 2 seconds each time after pressing the Function button until you reach the desired pattern. 4. If for any reason the signal from the remote (transmitter) to the control box (receiver) hangs up, please turn off and then restart the power to the set. 5. If a power interruption, the system’s memory keeps the last light pattern displayed. 6. The effective operating distance of the remote is 33′(10m) Setting Same Light Pattern On Multiple Sets Before installing your sets you will need to preset each string to the same light pattern. 1. Plug one set into a working 120V outlet. 2. Using any remote press the Function button until you have selected the desired lighting effect and note that pattern from the remote. 3. Unplug the set and then plug in the next set into the same outlet for ease of controlling. 4. With the remote follow Steps 2 and 3 setting the same light pattern (same function ) as the previous set. 5. When the strings are all set to the same function, power up all sets using multiple outlets. They will all light displaying the same pattern as the control module contains a built-in memory function. Once plugged in each set will start through their pattern. 6.To have all sets start together, press OFF on your remote and now press ON. 7. Install your sets. Follow step 6 to get all your sets operating on the same light pattern. Notes: 1. With all sets lighted, pressing the Function button will change all sets to the same (next) pattern. 2. These are Radio Frequency controlled devices. ALL sets within the effective range will be affected and controlled using any one remote. 3. To have different lighting patterns, in Step 2 set each string to a different function. 4. To group sets together to their own function follow the above setting one group to its same function and then the second to their same yet different function. 5. If used with a mechanical/digital timer, only one timer must control all sets. In this case, do not turn sets off using the remote or sets will not turn on with timer. Fig. 2 Fig. 3 Fig.1 Fig. 1 Fig. 2 6. Setting the same light pattern works ONLY with lights sets having the same number of LEDs. 7. Due to component tolerances there will be cycle time differences between sets. BATTERY CAUTION: • Always purchase the correct size and grade of battery most suitable for the intended use. • Replace all batteries of a set at the same time. • Clean the battery contacts and also those of the device prior to battery installation. • Ensure the batteries are installed correctly with regard to polarity (+ and -). • Remove batteries from equipment which is not to be used for an extended period of time. •Remove used batteries promptly. NOTE: LEDs in this set are non-replaceable. Tampering with this set will void the warranty. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ＊ Reorient or relocate the receiving antenna. ＊ Increase the separation between the equipment and the receiver. ＊ Connect the equipment into an outlet on a circuit different …

Text truncated - open the document above for the full version.

Page: 1

Page: 2 Page: 3 Page: 4 Page: 5

FCC ID: YLI720002011B Report No.: RF110609D04 Operational Description The transmitter of the EUT (Color Effects TM Remote Control) is powered by 3Vdc from batteries. The type of antenna is PCB antenna. The output power of this device is very low. Under normal use condition, the transmitter and the receiver are quite close, so high EIRP power is neither necessary nor allowed because of interference.

Report No.: RF110609D04 1 Report Format Version 4.0.0 FCC TEST REPORT REPORT NO.: RF110609D04 MODEL NO.: 720002011B FCC ID: YLI720002011B RECEIVED: Jun. 9, 2011 TESTED: Jun. 10, 2011 ISSUED: Jun. 15, 2011 APPLICANT: H.S. CRAFT MANUFACTURING CO. ADDRESS: 10F, NO. 35, GUANG FU N. ROAD, TAIPEI, TAIWAN ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan This test report consists of 25 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF110609D04 2 Report Format Version 4.0.0 Table of Contents RELEASE CONTROL RECORD..............................................................................3 1. CERTIFICATION..........................................................................................4 2. SUMMARY OF TEST RESULTS..................................................................5 2.1 MEASUREMENT UNCERTAINTY...............................................................5 3. GENERAL INFORMATION..........................................................................6 3.1 GENERAL DESCRIPTION OF EUT............................................................6 3.2 DESCRIPTION OF TEST MODES..............................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST.........................................7 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:.............8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS...........................10 3.4 DESCRIPTION OF SUPPORT UNITS......................................................10 4. TEST TYPES AND RESULTS....................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT............................................11 4.2 RADIATED EMISSION MEASUREMENT.................................................11 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...............................11 4.2.2 TEST INSTRUMENTS..............................................................................12 4.2.3 TEST PROCEDURES...............................................................................13 4.2.4 DEVIATION FROM TEST STANDARD.....................................................13 4.2.5 TEST SETUP............................................................................................14 4.2.6 EUT OPERATING CONDITIONS..............................................................14 4.2.7 TEST RESULTS........................................................................................15 4.3 20dB OCCUPIED BANDWIDTH MEASUREMENT...................................18 4.3.1 LIMITS OF EMISSION BANDWIDTH MEASUREMENT...........................18 4.3.2 TEST INSTRUMENTS..............................................................................18 4.3.3 TEST PROCEDURE.................................................................................18 4.3.4 DEVIATION FROM TEST STANDARD.....................................................19 4.3.5 TEST SETUP............................................................................................19 4.3.6 TEST RESULTS........................................................................................20 4.4 DEACTIVATION TIME...............................................................................21 4.4.1 LIMITS OF DEACTIVATION TIME MEASUREMENT................................21 4.4.2 TEST INSTRUMENTS..............................................................................21 4.4.3 TEST PROCEDURES...............................................................................21 4.4.4 DEVIATION FROM TEST STANDARD.....................................................21 4.4.5 TEST SETUP............................................................................................21 4.4.6 TESE RESULTS........................................................................................22 5. PHOTOGRAPHS OF THE TEST CONFIGURATION.................................23 6. INFORMATION ON THE TESTING LABORATORIES...............................24 7. APPENDIX A – MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB......................................................25 Report No.: RF110609D04 3 Report Format Version 4.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF110609D04 Original release Jun. 15, 2011 Report No.: RF110609D04 4 Report Format Version 4.0.0 1. CERTIFICATION PRODUCT: Color Effects TM Remote Control BRAND NAME: GE MODEL NO.: 720002011B APPLICANT: H.S. CRAFT MANUFACTURING CO. TESTED: Jun. 10, 2011 TEST SAMPLE: MASS-PRODUCTION STANDARDS: FCC Part 15, Subpart C (Section 15.231) ANSI C63.4-2003 ANSI C63.10-2009 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: ( Jessica Cheng / Specialist ) APPROVED BY : , DATE: ( Ken Liu / Manager ) Report No.: RF110609D04 5 Report Format Version 4.0.0 2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15, Subpart C (Section 15.231) STANDARD SECTION TEST TYPE AND LIMIT RESULT REMARK 15.207 Conducted Emission Test N/A Power supply is 3Vdc from batteries 15.209 15.231(b) Radiated Emission Test PASS Minimum passing margin is –14.0dB at 3037.20MHz 15.231(c) Emission Bandwidth Measurement PASS Meet the requ…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST