YW2Y-R0023LOGITECH KEYBOARD CASE BY ZAGG

Provide Protection, Bluetooth Keyboard, and integrated Stand for tablet device Storage and Protection It attaches to the front of the tablet device by inserting the tablet face first into the opening of the tray. The tablet device is safely held into position, and protected, by using a shock absorbing, friction fitting around the inside edges of the product. Use To utilize the stand and keyboard function of the product, you remove the tablet device by gently prying the tablet out of the case. You then lift up the hinge and lock it in place by choosing your desired angle and sliding the tabs down into the proper slots and pushing back to lock hinge in place. Then, simply place tablet device (either in portrait or landscape mode) into the opening, running from end to end, and rest it against the raised hinge. Bluetooth Keyboard Pairing To utilize the Bluetooth keyboard, you must pair it to the tablet. We will demonstrate this process using an iPad, however, it will be similar for all tablet devices. The pairing process is as follows: 1. On the tablet, click on Settings icon on desktop 2. On tablet, Click General 3. On tablet, Click Bluetooth 4. On the product, slide the power button to on 5. On product, Click on pair 6. The tablet will display a code 7. Type the code on the keyboard and press enter 8. Your product is now paired to your tablet device FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC ID: YW2Y-R0023 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

1234 A B C D 4 321 D C B A BCM2042 EEPROM 24 MHz Keymartix Led indicator Low battery Monitor Power supply PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn

External Photo

FCC Certification Label FCC ID: YW2Y-R0023 This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:1. This device may not cause harmful interference, and 2. This device must accept any interference received,including interference that may cause undesired operation. Label Location on EUT EUT Top View/ FCC ID Label Location

Internal Photo Antenna

Operational Description Keyboard:(1)Once a key or multi keys of keyboard are pressed or released,the signal change will be detected by MCU. (2)The MCU converts these signals into HID data packet. (3)The MCU send HID data packet to Bluetooth Module via uart interface. (4)The BT module transmits the modulation signal on frequency of 2.4GHz using FHSS modulation. Receiver:(1)Once the receiver recelves the modul ation signal,it will demodulation the signal through Bluetooth Chip and will respond with signal to Bluetooth Stack. (2)The BT Stack converts the signal into an acceptable format recelved by PC.

1 2 34 ABCD 4 3 2 1 D CBA Product Name Schematic Name Revision Page Date Drawing byAuthorize by ITON TECHNOLOGY Auditing by GND 1 GND 2 P44 3 P43 4 P14 5 P12 6 P21 7 P20 8 P13 9 P41 10 P32 11 P33 12 3P0_1 13 P40 14 P34 15 P35 16 P17 17 GND 18 P16 19 P22 20 VBATT 21 P24 22 1P8V_1 23 P31 24 P23 25 P15 26 3P0V 27 P00 28 P30 29 WP 30 P05 31 P04 32 P07 33 P06 34 UP_TX 35 UP_RX 36 P02 37 P25 38 RESET_IN 39 P03 40 P01 41 P27 42 P26 43 P42 44 P10 45 P11 46 P45 47 GND 48 U1 PA-48-V3 COLUMN0COLUMN1 C4 10uF C7 10uF C9 10uF C2 10uF VBATT2 VBATT_IN ROW0 ROW1ROW2ROW3ROW4ROW5ROW6ROW7 COLUMN2COLUMN3COLUMN4 COLUMN5COLUMN6 COLUMN7COLUMN8COLUMN9 COLUMN10COLUMN11COLUMN12 COLUMN13COLUMN14COLUMN15 P34 3P0V R5 10K 3P0V UP_TXUP_RX 1234 J1 CON4 UP_TXUP_RX VBATT R410k C140.1uF C12 10uF C8 10uF R7 100K R11 47K Connect Search button COLUMN0 ROW2 C6 0.1uF R1 330R D1 P44 P45 1 2 3 ON OFFSW-POWER VBATT Battery Monitor I S P P o r t Download eeprom configuration file Battery Monitor 3P0V Power DC BUCK OUTPUT 3P0V C110.1uF P45 P33P32 P42 P43 COLUMN16COLUMN17 BT1 BATTERY VBATT_IN 1234567891011121314151617181920212223242526 Connect1CON26 NREST ROW0ROW1ROW2ROW3ROW4ROW5ROW6ROW7COLUMN0COLUMN1COLUMN2COLUMN3COLUMN4COLUMN6COLUMN5 C2,C9,C14 ,Should be near the Pin21 of U1 VCC 1 D- 2 D+ 3 GND 4 AGND 5 MICRO USB C10 4.7UF R810K R9 470R D2 VBATT_IN C12,C6,C8 Should be VBATT Vout 5 NC 4 Vin 1 GND 2 CE 3 U3 2.8V LDO VBATT2 VBATT C310uF C1310uF Li MEI Hai Y-R0027_Ver2.0 V0 1 of 1 20011-05-03 BCM2042 Battery Cap MotionKEY Button CHRG 1 GND 2 BATT 3 Vcc 4 PROG 5 U2 4054 Vcc C150.1uF Vcc VBATT2 C10.1uF COLUMN7COLUMN8COLUMN9COLUMN10COLUMN11COLUMN12COLUMN15COLUMN14COLUMN13 RXTX R12 22R R13 22R ZD1 ZD2

FCC PART 15.249 EMI MEASUREMENT AND TEST REPORT For Wagons Digital Co., Ltd. Flat/Rm. 1701, 17/F., Henan Building, 90 Jaffe Road, Wanchai, Hong Kong FCC ID: YW2Y-R0023 May 13, 2011 This Report Concerns: Original Report Equipment Type: Logitech Keyboard Case by ZAGG Test Engineer: Eric Li Report No.: BST11050002Y-1ER-3 Receive EUT Date/Test Date: May 9, 2011/ May 10-13,2011 Reviewed By: Christina Prepared By: Shenzhen BST Technology Co.,Ltd. 3F,Weames Technology Building, No. 10 Kefa Road, Science Park, Nanshan District,Shenzhen,Guangdong,China Tel: 0755-267477513 Fax: 0755-267477513 ext.826 Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Shenzhen BST Technology Co.,Ltd. This report must not be used by the client to claim product certification,approval,or endorsement by NVLAP, NIST or any agency of the US Government. Wagons Digital Co., Ltd. FCC ID: YW2Y-R0023 BST FCC ID REPORT : BST10050286R-3 Page 2/17 TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................3 1.1. Report information ............................................................................................................3 1.2. Measurement Uncertainty .................................................................................................3 2. PRODUCT DESCRIPTION ......................................................................................................4 2.1. EUT Description ...............................................................................................................4 2.2. Block Diagram of EUT Configuration..............................................................................4 2.3. Support Equipment List ....................................................................................................5 2.4. Test Conditions .................................................................................................................5 3. FCC ID LABEL...........................................................................................................................6 4. TEST RESULTS SUMMARY ...................................................................................................7 Modifications ................................................................................................................................7 5. TEST EQUIPMENT USED .......................................................................................................8 6. ANTENNA REQUIREMENT ...................................................................................................9 6.1. STANDARD APPLICABLE............................................................................................9 6.2. ANTENNA CONNECTED CONSTRUCTION ..............................................................9 6.3. Result ................................................................................................................................9 7. CONDUCTED POWER LINE TEST .....................................................................................10 7.1. Test Equipment ...............................................................................................................10 7.2. Test Procedure ................................................................................................................10 7.3. Test Setup........................................................................................................................10 7.4. Conducted Power line Emission Limits..........................................................................10 7.5. Conducted Power Line Test Result.................................................................................11 8. RADIATED EMISSION TEST ...............................................................................................13 8.1. Test Equipment ...............................................................................................................13 8.2. Test Procedure ................................................................................................................13 8.3. Radiated Test Setup ........................................................................................................13 8.4. Radiated Emission Limit.................................................................................................14 8.5. Radiated Emission Test Result .......................................................................................15 9. BAND EDGE .............................................................................................................................17 9.1. Test Equipment ...............................................................................................................17 9.2. Test Procedure ................................................................................................................17 9.3. Band Edge FCC 15.249(d) Limit ....................................................................................17 9.4. Band Edge Test Result ....................................................................................................17 Wagons Digital Co., Ltd. FCC ID: YW2Y-R0023 BST FCC ID REPORT : BST10050286R-3 Page 3/17 1. GENERAL INFORMATION 1.1. Report information 1.1.1.This report is not a certificate of quality; it only applies to the sample of the specific product/equipment given at the time of its testing. The results are not used to indicate or imply that they are application to the similar items. In addition, such results must not be used to indicate or imply that BST approves recommends or endorses the manufacture, supplier or use of such product/equipment, or that BST in any way guarantees the later performance of the product/equipment. 1.1.2.The sample/s mentioned in this report is/are supplied by Applicant, B…

Text truncated - open the document above for the full version.

Radiated emissions test Conducted emissions test