ZRQ-K3Penclic wireless keyboard

1 2 www.penclic.se 3 2 EN Welcome to the quick guide. Penclic Mini Keyboard combines ergonomically sound design with modern keyboard technology WREULQJ\RXFRPIRUWDQGHIʖFLHQF\ Penclic Mini Keyboard setup Insert the rechargeable batteries and start charging with the included micro-USB charging cable. Insert the Nano-USB receiver into the USB port, then set the keyboard power switch on the bottom of the keyboard to ON. Driver installation starts automatically. The wireless connection activates automatically. How to use your Penclic Mini Keyboard Penclic Mini Keyboard K2 (wireless) has 1 LED indicating battery status. Fn +Function F2Mute F3Lower volume F4Higher volume F9Pause/Break F10Scroll Lock F11Num Lock F12Print Screen DeleteInsert Up arrowPage Up Left arrowHome Down ArrowPage Down Right ArrowEnd LED behaviorIndication UHGʗDVKThe keyboard on/ off switch was set to on. /('ʗDVKHVUHG repeatedly Recharge your battery. (NOTE:Do not recharge non-rechargeable batteries.) /('ʗDVKHV green repeatedly Battery is currently being recharged. LED is constantly green Battery is currently being recharged. Num Lock actives the numpad functions which is the smaller orange numbers. Special functions (blue text) activated by holding the Fn key and then pressing: 4  7HFKQLFDOVSHFLʖFDWLRQV ɒThe supported platforms for Penclic Mini Keyboard are all operating systems that support HID 1.1. These include Windows XP or later, Mac OSX version 10.1 or later and most /LQX[%6'ʗDYRUV1RH[WUDVRIWZDUHGULYHU installation is needed. ɒConnection USB. ɒAAA 1.2V NiMH Recharging battery (Everyday use last approximately 2 months before charging is needed). -Charging via USB . ɒ /5$$$9$ONDOLQH1RQHUHFKDUJHDEOH batter y can be used. NOTE: DO NOT RECHARGE. ɒNano USB-receiver 2,4GHz. :LUHOHVVUHDFKPLQLPXPPHWUHV -Connection via USB . ɒEnergy saving mode starts after 10 min, press a button to start. ɒMAC operating systems do not support all the special functions. Measurements ɒHeight: 6 mm (21 mm at top), %DVH[PP ɒWeight: 381g including 1.4m cable. Troubleshooting ɒMake sure the Penclic Mini Keyboard USB FRQQHFWRULVʖUPO\DWWDFKHGWRWKHFRPSXWHUɋV USB port. ɒUn-plug and re-plug the Nano-USB receiver. ɒConnect to another USB port. ɒConnect to another computer. ɒCheck the batter y. Technical support Should you require additional technical support with your Penclic®, please use our Web site (www.penclic.se) for further information or contact our support group through e-mail. Call Technical Support during business hours, Central European time (UTC+1). Contact  [email protected] FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC WARNING This device complies with Industry Canada RSS-210 standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 EUT View 3 EUT View 4

Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 Solder Board-Component View 1 RF Antenna Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 Solder Board-Component View 2

Penclic AB Model: K2.1 REPORT NO.: STR14098056I PAGE 1 OF 30 FCC PART 15.249 FCC Part 15C Measurement and Test Report For Penclic AB Vendev. 90, Danderyd, Sweden FCC ID: ZRQ-K3 FCC Rule(s): FCC Part 15.249 Product Description: Penclic wireless keyboard Tested Model: K2.1 Report No.: STR14098056I Tested Date: 2014-09-09 to 2014-10-30 Issued Date: 2014-10-30 Tested By: Jason Su / Engineer Reviewed By: Lahm Peng / EMC Manager Approved & Authorized By: Jandy so / PSQ Manager Prepared By: Shenzhen SEM.Test Technology Co., Ltd. 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen SEM.Test Technology Co., Ltd. Penclic AB Model: K2.1 REPORT NO.: STR14098056I PAGE 2 OF 30 FCC PART 15.249 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 3 1.2 TEST STANDARDS ................................................................................................................................................... 4 1.3 TEST METHODOLOGY ............................................................................................................................................. 4 1.4 TEST FACILITY ....................................................................................................................................................... 4 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 5 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 6 3. ANTENNA REQUIREMENTS ................................................................................................................................ 7 3.1 STANDARD APPLICABLE ......................................................................................................................................... 7 3.2 TEST RESULT.......................................................................................................................................................... 7 4. RADIATED EMISSIONS ......................................................................................................................................... 8 4.1 MEASUREMENT UNCERTAINTY .............................................................................................................................. 8 4.2 STANDARD APPLICABLE ......................................................................................................................................... 8 4.3 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 8 4.4 TEST PROCEDURE ................................................................................................................................................... 9 4.5 CORRECTED AMPLITUDE & MARGIN CALCULATION .............................................................................................. 9 4.6 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 10 4.7 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 10 5. OUT OF BAND EMISSIONS ................................................................................................................................. 21 5.1 STANDARD APPLICABLE ....................................................................................................................................... 21 5.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 21 5.3 TEST PROCEDURE ................................................................................................................................................. 21 5.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 21 5.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 21 6. EMISSION BANDWIDTH ..................................................................................................................................... 24 6.1 STANDARD APPLICABLE ....................................................................................................................................... 24 6.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 24 6.3 TEST PROCEDURE ................................................................................................................................................. 24 6.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 24 6.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 24 7. CONDUCTED EMISSIONS .................................................................................................................................. 27 7.1 MEASUREMENT UNCERTAINTY ...........................................................…

Text truncated - open the document above for the full version.

Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Conducted Emission Test Setup Only Charging Radiation Emission Test Setup Only Charging Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 Radiation Emission Test Setup (Below 30MHz) Radiation Emission Test Setup (30MHz to 1GHz) Penclic AB Model: K2.1 REPORT NO.: STR14098056I FCC PART 15.249 Radiation Emission Test Setup (Above 1GHz)