ZRQ-R4PENCLIC MOUSE

WELCOME to the quick guide Penclic Mouse combines ergonomically sound design with modern mouse technology to bring you unparalleled precision, comfort and efficiency. Mouse setup Insert the battery into the mouse Charge the battery with the included micro usb charging cable until full. Set the mouse power switch on the bottom of the mouse to ON Trouble installing your Penclic Mouse R3. Please look at www.penclic.se/troubleshooting HOW TO USE YOUR Penclic Mouse 1, Hold Penclic Mouse like a pen, the bottom part acts like a traditional mouse. 2, Let your forearm and your hand rest on a surface, while keeping your shoulders relaxed. 3, The pen part can be adjusted to suit specific grips. Fixate the bottom part with one hand and rotate the pen to the preferred angle with the other. • Left click 1 • Right click 2 • Middle click 3 • Scroll wheel 4 • On‐off switch 5 • DPI switch 6 • Connect to new receiver button 7 TROUBLESHOOTING http://www.Penclic.se/troubleshooting • Check the battery. • When the battery needs charging the LED on the mouse will show red. When the battery is fully charged a green light will be displayed. • Cursor movement may be effected by very glossy surfaces. TECHNICAL SPECIFICATIONS The supported platforms for Penclic Mouse are all operating systems that support HID 1.1. These include Windows XP or later, Mac OSX version 10.1 or later and most Linux/BSD flavors. No extra software/driver installation is needed. • Operates on almost any surface without any pad or tablet. • Implements a 3-buttons and scroll wheel mouse. • AAA 1.2V NiMH Recharging battery (Everyday use last approximately 3 months before charging is needed). • LR 03/AAA/1.5V Alkaline None rechargeable battery can be used. NOTE: DO NOT RECHARGE • Energy saving mode starts after 10 min, press left click (button 1) to activate. • Wireless reach, minimum 5 metres. • Dpi settings 800-1200-1600. Measurements: • Height: 140 mm Base: 44.1 x 20 mm • Weight: 41 g TECHNICAL SUPPORT Should you require additional technical support with your Penclic Mouse™, please use our Web site for further information or contact our support group through e- mail. Call Technical Support during business hours, central European time plus one hour. Contact: + 46 8 544 98 995 or email: [email protected] FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC WARNING This device complies with Industry Canada RSS-210 standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a PCB and maximum -1.2dBi gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. SPRÅK: ord på 13 språk Svenska, norska, danska, finska, tyska, franska, spanska, italienska, holländska, portugisiska, turkiska och grekiska. + polska

Penclic AB Vendev. 90, 7tr 182 32 Danderyd, Sweden --------------------------------------------------------------------------------------------------------------------- Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: ZRQ-R4 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics ZRQ-R4_FCCID_Schematics Block Diagram ZRQ-R4_FCCID_BlockDiagram Operational Description ZRQ-R4_FCCID_OperationalDescription The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application.

Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 EUT View 3 EUT View 4 Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 EUT View 5 EUT View 6

Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: ZRQ-R4 Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: ZRQ-R4 Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 Solder Board-Component View 1 Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 Solder Board-Component View 2 EUT Housing and Board View 2 2.4G Antenna Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 Solder Board-Component View 3 Solder Board-Component View 4 Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 Solder Board-Component View 5

Penclic AB Model: R3 REPORT NO.: STR14018573I PAGE 1 OF 30 FCC PART 15.249 FCC Part 15C Measurement and Test Report For Penclic AB Vendev. 90, 7tr 182 32 Danderyd, Sweden FCC ID: ZRQ-R4 FCC Rule(s): FCC Part 15.249 Product Description: Penclic mouse Tested Model: R3 Report No.: STR14018573I Tested Date: 2014-01-20 to 2014-02-12 Issued Date: 2014-02-12 Tested By: Lebron Wang / Engineer Reviewed By: Lahm Peng / EMC Manager Approved & Authorized By: Jandy so / PSQ Manager Prepared By: Shenzhen SEM.Test Technology Co., Ltd. 1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen SEM.Test Technology Co., Ltd. Penclic AB Model: R3 REPORT NO.: STR14018573I PAGE 2 OF 30 FCC PART 15.249 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 3 1.2 TEST STANDARDS ................................................................................................................................................... 4 1.3 TEST METHODOLOGY ............................................................................................................................................. 4 1.4 TEST FACILITY ....................................................................................................................................................... 4 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 5 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 6 3. ANTENNA REQUIREMENTS ................................................................................................................................ 7 3.1 STANDARD APPLICABLE ......................................................................................................................................... 7 3.2 TEST RESULT.......................................................................................................................................................... 7 4. RADIATED EMISSIONS ......................................................................................................................................... 8 4.1 MEASUREMENT UNCERTAINTY .............................................................................................................................. 8 4.2 STANDARD APPLICABLE ......................................................................................................................................... 8 4.3 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 8 4.4 TEST PROCEDURE ................................................................................................................................................... 9 4.5 CORRECTED AMPLITUDE & MARGIN CALCULATION .............................................................................................. 9 4.6 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 10 4.7 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 10 5. OUT OF BAND EMISSIONS ................................................................................................................................. 21 5.1 STANDARD APPLICABLE ....................................................................................................................................... 21 5.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 21 5.3 TEST PROCEDURE ................................................................................................................................................. 21 5.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 21 5.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 21 6. EMISSION BANDWIDTH ..................................................................................................................................... 24 6.1 STANDARD APPLICABLE ....................................................................................................................................... 24 6.2 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 24 6.3 TEST PROCEDURE ................................................................................................................................................. 24 6.4 ENVIRONMENTAL CONDITIONS ............................................................................................................................ 24 6.5 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 24 7. CONDUCTED EMISSIONS .................................................................................................................................. 27 7.1 MEASUREMENT UNCERTAINTY ...............................................................…

Text truncated - open the document above for the full version.

Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Conducted Emission Test Setup Only Charging Radiation Emission Test Setup Only Charging Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 Radiation Emission Test Setup (Below 30MHz) Radiation Emission Test Setup (30MHz to 1GHz) Penclic AB Model: R3 REPORT NO.: STR14018573I FCC PART 15.249 Radiation Emission Test Setup (Above 1GHz)