ZY4CM49Transmitter

CM-49 Hand-held remote 15 channel English 2 CM-49 is a hand-held remote with 15 channels for operating and programming blinds at the push of a button. Blinds can be moved to any desired position or to a preset favourite position. The wall mounting clip for this remote control is included by default. For the latest information and updated manuals, visit rtube.nl/cm-49 15 433 .92MHz 2.32dBm CR2430 3.0V 120 mm45 mm14 mm-10°C~50°C ChannelsMax. blinds FrequencyRange Frequency emission power Power supply LengthWidthHeightWorking temperature Certificates unlimited 30 m with 1 concrete wall 3 Safety WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury. Do not let children play with the blind and/or remote control. Take care that the blind can move freely and is not blocked by any objects. Do not paint the device. Keep the device dry. Do not drop, knock, or shake the device. Rough handling can break internal circuit boards. Do not ingest battery, Chemical Burn Hazard This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children.If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Replacement of a battery with an incorrect type that can defeat a safeguard. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. Leaving a battery in an extremely high temperature surround- ing environment that can result in an explosion or the leakage of flammable liquid or gas. A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. 4 Cleaning Follow these general rules when cleaning the outside of the device and its components: Use a damp, soft, lint-free cloth. Avoid getting moisture in openings. Do not use aerosol sprays, solvents, alcohol, or abrasives. Service & Support Do not perform repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside. Warranty Service First follow the advice in this manual. If the product appears to be damaged or does not function properly, go to your local dealer for instructions on how to obtain warranty service. Recycle This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collec-tion systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. EU Declaration Hereby, Coulisse declares that the radio equipment type CM-49 is in compliance whith directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: support.motionblinds.com 5 FCC Manual I FCC ID ZY4CM49 Regulatory Information 1 FCC Information for User This product does not contain any user-serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. 2 FCC Electronic Emission Notices This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2. This device must accept any interference received, including interference that may cause undesired operation. 3 FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio-frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 6 Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interference at their own expense. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the distance separating the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help 7 1 Buttons/control Up Channel indicator Down Previous Channel Next Channel Centre (stop/favourite) Pair button The center button has two functions: press to stop the blind, hold to move the blind to its favorite position. 1. BUTTONS/CONTROL 8 2 + - CR2430 3,0V Changing the battery The battery indicator will show when the battery needs to be replaced. 2. CHANGING THE BATTERY 9 3 Remote holder Different materials require different types of fittings. Always choose screws and plugs that are specially suited to the material. 3. REMOTE HOLDER 10 4 Pair a remote 4. PAIR A REMOTE 11 4.1 4.2 4.3 Shortly press the program button on the motor. The blind will start stepping, indicating that program mode has been activated. (The blind keeps stepping until the program mode is deactivated) Repeat steps 4.1 - 4.3 to remove a blind from a channel…

Text truncated - open the document above for the full version.

Coulisse B.V. Vonderweg 48, Enter, 7468 DC, Netherlands Date: August 09, 2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: ZY4CM49 US Agent – Attestation Statement / Part 2.911(d)(7) Coulisse B.V. certifies, that as of August 09, 2024, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: ZY4CM49. Coulisse B.V., accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Coulisse B.V. for FCC ID: ZY4CM49. Designated Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Company: Coulisse B.V. Designated Agent: FCC US Agent, LLC Company Representative: Bas Klein Tuente Designated Agent Representative: Tim Payne Signature: Signature:

Applicant Company Header TO WHOM IT MAY CONCERN: Product name: Transmitter Model: CM-49 FCC ID: ZY4CM49 We place the FCC label under the equipment cover due to below reasons: 1. The FCC label is visible when user open the cover and install the batteries, otherwise, the equipment doesn’t work. 2. The equipment is separated from the battery in the packing box; users can read the FCC ID information at the time of open the cover to install the battery. 3. Label placed on the exterior of the equipment affect the appearance according to design requirements; otherwise, it would be easily removed or damaged. Yours sincerely, Contact name: Bas klein Tuente Company name: Coulisse B.V. Address: Vonderweg 48, 7468 DC Enter, THE NETHERLANDS E-mail: Tel: +86 310547 855 831

External Photos Documentation Applicant: Coulisse B.V. Page 1 of 4 Product: Transmitter FCC ID: ZY4CM49 Model: CM-49 External Photos Documentation Applicant: Coulisse B.V. Page 2 of 4 Product: Transmitter FCC ID: ZY4CM49 Model: CM-49 External Photos Documentation Applicant: Coulisse B.V. Page 3 of 4 Product: Transmitter FCC ID: ZY4CM49 Model: CM-49 External Photos Documentation Applicant: Coulisse B.V. Page 4 of 4 Product: Transmitter FCC ID: ZY4CM49 Model: CM-49

Label & Location Label position Label

Report No: 709502404395-00C EMC_SHA_F_R_02.06E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 1 of 2 Rev. 171.00 RF Exposure Estimation 1. Introduction Applicant: Coulisse B.V. Address: Vonderweg 48, 7468 DC Enter, THE NETHERLANDS Product: Transmitter FCC ID: ZY4CM49 Model No.: CM-49 Reference RF report # 709502404395-00B 2. B.2 Blanket 1 mW Blanket Exemption According to KDB 447498 D04, the 1 mW Blanket Exemption of § 1.1307(b)(3)(i)(A) applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power of no more than 1 mW, regardless of separation distance. The 1 mW blanket exemption applies at separation distances less than 0.5 cm, including where there is no separation. This exemption shall not be used in conjunction with other exemption criteria other than those for multiple RF sources in paragraph § 1.1307(b)(3)(ii)(A). The 1 mW exemption is independent of service type and covers the full range of 100 kHz to 100 GHz, but it shall not be used in conjunction with other exemption criteria or in devices with higher-power transmitters operating in the same time-averaging period. Exposure from such higher-power transmitters would invalidate the underlying assumption that exposure from the lower-power transmitter is the only contributor to SAR in the relevant volume of tissue. 3. RF Exposure Evaluation Per the test report included herein, for 433.92MHz According to C63.10 Annex G EIRP = pt × gt =( E × d) 2 /30, so pt=( E × d) 2 /30* gt where pt is the transmitter output power in watts gt is the numeric gain of the transmitting antenna (dimensionless) E is the electric field strength in V/m d is the measurement distance in meters (m) transmitter output power for 433.92MHz Function Field strength (E): 85.41 (dBuV/m) = 0.02 (V/m) Measurement distance (D): 3 (m) Transmitter output power (TP): 0.00000695(W) Transmitter output power (TP): 0.00695(mW) Report No: 709502404395-00C EMC_SHA_F_R_02.06E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 2 of 2 Rev. 171.00 We used the maximum ERP/EIRP to perform RF exposure exemption evaluation. Evaluation method Exempt Limit (mW) Verdict ◼ Blanket 1 mW Blanket Exemption 1mW Yes  MPE-based Exemption (ERP) 7mW (ERP) N/A  SAR-based Exemption (Pth) 3060mW N/A So, the device is qualified for SAR test exemption, the exemption report is in lieu of the SAR report. - TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch Reviewed by: Prepared by: Tested by: _____________________ _____________________ ______________________ Hui TONG Yongqing ZHENG Tianji XU EMC Section Manager EMC Project Engineer EMC Test Engineer Date: June 26, 2024 Date: June 26, 2024 Date: June 26, 2024 -------------------------------------------------------End of Test Report--------------------------------------------------------------------

Coulisse B.V. Vonderweg 48, 7468 DC Enter, THE NETHERLANDS Antenna Information To whom it may concern, Product name: Transmitter Model: CM-49 FCC ID: ZY4CM49 The applicable FCC rule part of this product is § 15.231, radiated measurements are used to show compliance with FCC limits for fundamental and spurious emissions. The Antenna information as below for your reference. Antenna photo: Antenna transmission frequency: 433.92MHz Antenna type: PCB antenna Yours sincerely, Company Officer: Mr. Bas klein Tuente Telephone Number: +86 310547 855 831 Email: Antenna

Report Number: 709502404395-00B EMC_SHA_F_R_02.01E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 1 of 20 Rev. 23.00 FCC - TEST REPORT Report Number : 709502404395-00B Date of Issue: August 28, 2024 Model : CM-49 Product Type : Transmitter Applicant : Coulisse B.V. Address : Vonderweg 48, 7468 DC Enter, THE NETHERLANDS Production Facility : Ningbo Dooya Mechanic & Electronic Technology Co., Ltd. Address : No.168 Shengguang Road,Luotuo,Zhenhai 315202 Ningbo,Zhejiang province, : PEOPLE'S REPUBLIC OF CHINA Test Result : ◼ Positive  Negative Total pages including Appendices : 20 TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch is a subcontractor to TÜV SÜD Product Service GmbH according to the principles outlined in ISO 17025. TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch reports apply only to the specific samples tested under stated test conditions. Construction of the actual test samples has been documented. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. The manufacturer/importer is responsible to the Competent Authorities in Europe for any modifications made to the production units which result in non-compliance to the relevant regulations. TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch shall have no liability for any deductions, inferences or generalizations drawn by the client or others from TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch issued reports. This report is the confidential property of the client. As a mutual protection to our clients, the public and ourselves, extracts from the test report shall not be reproduced except in full without our written approval. Report Number: 709502404395-00B EMC_SHA_F_R_02.01E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 2 of 20 Rev. 23.00 1 Table of Contents 1 Table of Contents ..................................................................................................................................................2 2 Details about the Test Laboratory & Report Modification Record .........................................................................3 3 Description of the Equipment Under Test .............................................................................................................4 4 Summary of Test Standards .................................................................................................................................5 5 Summary of Test Results ......................................................................................................................................6 6 General Remarks ..................................................................................................................................................7 7 Test Setups ...........................................................................................................................................................8 8 Test Methodology ..................................................................................................................................................9 8.1 Conducted Emission .....................................................................................................................................9 8.2 Radiated Emission ..................................................................................................................................... 10 8.3 Bandwidth Measurement............................................................................................................................ 14 8.4 Deactivation Time ....................................................................................................................................... 15 9 Systems test configuration ................................................................................................................................. 16 10 Test Equipment List ............................................................................................................................................ 17 11 System Measurement Uncertainty ..................................................................................................................... 18 12 Photographs of Test Set-ups ......................................................................................................................... 19 13 Photographs of EUT ....................................................................................................................................... 20 Report Number: 709502404395-00B EMC_SHA_F_R_02.01E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 3 of 20 Rev. 23.00 2 Details about the Test Laboratory & Report Modification Record Details about the Test Laboratory Test Site 1 Company name: TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch No.16 Lane, 1951 Du Hui Road, Shanghai 201108, P.R. China Telephone: +86 21 6141 0123 Fax: +86 21 6140 8600 FCC Registration No.: 820234 FCC Designation Number: CN1183 Report Modification Record: Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. Report No. Description of Change Date of Issue 709502404395-00B First Issue 08/28/2024 Report Number: 709502404395-00B EMC_SHA_F_R_02.01E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 4 of 20 Rev. 23.0…

Text truncated - open the document above for the full version.

Applicant: Coulisse B.V. Product: Transmitter FCC ID: ZY4CM49 Model: CM-49 ©2024 Not to be reproduced, except in its entirety, Page 1 of 1 without the Permission of TÜ V SÜ D Certification and Testing (China) Co., Ltd. Shanghai Branch PHOTOGRAPHS OF TEST SET UP Field Strength and Harmonics Test Setup Radiated Emission Setup 30MHz ~ 1GHz 1GHz ~ 4.5GHz